Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2013.12–2016.11
RM3160E _57 Power Source / Network _019704 NETWORKING _0095663 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  AFS ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
AFS ECU Communication Stop Mode Either condition is met:
·

"Headlight swivel (AFS)" is not displayed on the CAN Bus Check screen of the GTS

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "AFS ECU Communication Stop Mode" in "DTC Combination Table" are output

Click here(Click here)


·

Headlight leveling ECU assembly branch line or connector

·

Power source circuit of headlight leveling ECU assembly

·

Headlight leveling ECU assembly ground circuit

·

Headlight leveling ECU assembly



WIRING DIAGRAM

C286873
2.135,1.281 1.646,0.656 1.646,0.656 1.51,0.656 false 4.792,1.281 5.354,0.594 5.354,0.594 5.469,0.594 false 0.052,0.021 1.969,0.292 1.917,0.271 12 false V Bus (for LHD): 2.281,0.51 2.896,0.708 0.615,0.198 10 false DLC3 1.844,3.781 2.896,4.115 1.052,0.333 10 false DSS-IG 0.719,2.198 1.49,2.396 0.771,0.198 10 false 120 Ω 6.135,2.167 6.906,2.365 0.771,0.198 10 false 120 Ω 2.594,3.531 2.75,3.729 0.156,0.198 10 false 1 2.76,3.656 3.073,3.854 0.313,0.198 10 false IG 2.99,3.281 3.604,3.479 0.615,0.198 10 false CANH 3.115,3.094 3.271,3.292 0.156,0.198 10 false 6 3.688,3.094 3.844,3.292 0.156,0.198 10 false 7 3.51,3.281 4.125,3.479 0.615,0.198 10 false CANL 3.927,3.667 4.24,3.865 0.313,0.198 10 false E1 4.177,3.563 4.333,3.76 0.156,0.198 10 false 9 2.365,4.219 2.823,4.417 0.458,0.198 10 false A67 2.729,4.219 4.188,4.604 1.458,0.385 10 false Headlight Leveling ECU Assembly 0.688,3.865 2.521,4.063 1.833,0.198 10 false Trouble Area 1.115,4.99 3.208,5.208 2.094,0.219 10 false : CAN Main Bus Line (CANH) 1.115,5.396 5.094,5.594 3.979,0.198 10 false : CAN Main Bus Line (CANL) 4.26,4.99 6.073,5.24 1.813,0.25 10 false : CAN Branch Line (CANH) 4.26,5.406 6.146,5.708 1.885,0.302 10 false : CAN Branch Line (CANL) 0.677,2.813 1.135,3.01 0.458,0.198 10 false ECM 5.552,0.5 6.781,0.99 1.229,0.49 10 false No. 4 CAN Junction Connector 0.25,0.552 1.479,1.01 1.229,0.458 10 false No. 3 CAN Junction Connector 5.792,2.792 6.99,3.438 1.198,0.646 10 false Combination Meter Assembly

C295747
4.802,1.281 4.208,0.281 4.208,0.281 4.094,0.281 false 2.802,1.281 2.417,0.708 2.417,0.708 2.333,0.708 false 0.073,0.042 2.573,0.458 2.5,0.417 12 false V Bus (for RHD): 4.938,0.552 5.552,0.75 0.615,0.198 10 false DLC3 2.854,0.177 4.094,0.979 1.24,0.802 10 false No. 4 CAN Junction Connector 1.083,0.604 2.323,1.406 1.24,0.802 10 false No. 3 CAN Junction Connector 0.698,2.177 1.469,2.375 0.771,0.198 10 false 120 Ω 6.115,2.177 6.885,2.375 0.771,0.198 10 false 120 Ω 5.792,2.792 6.99,3.406 1.198,0.615 10 false Combination Meter Assembly 0.656,2.802 1.115,3 0.458,0.198 10 false ECM 1.125,4.99 5.104,5.188 3.979,0.198 10 false : CAN Main Bus Line (CANH) 1.125,5.396 5.104,5.594 3.979,0.198 10 false : CAN Main Bus Line (CANL) 4.271,4.99 6.063,5.292 1.792,0.302 10 false : CAN Branch Line (CANH) 4.271,5.396 6.021,5.646 1.75,0.25 10 false : CAN Branch Line (CANL) 3.104,3.042 3.26,3.24 0.156,0.198 10 false 6 3.688,3.042 3.844,3.24 0.156,0.198 10 false 7 4.177,3.531 4.333,3.729 0.156,0.198 10 false 9 2.583,3.531 2.74,3.729 0.156,0.198 10 false 1 2.938,3.271 3.552,3.469 0.615,0.198 10 false CANH 3.5,3.271 4.115,3.469 0.615,0.198 10 false CANL 2.76,3.646 3.073,3.844 0.313,0.198 10 false IG 3.917,3.646 4.229,3.844 0.313,0.198 10 false E1 2.396,4.219 2.854,4.417 0.458,0.198 10 false A67 2.74,4.208 4.188,4.854 1.448,0.646 10 false Headlight Leveling ECU Assembly 1.875,3.781 3.708,3.979 1.833,0.198 10 false DSS-IG 0.667,3.865 2.5,4.063 1.833,0.198 10 false Trouble Area

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON and wait at least 13 seconds.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (HEADLIGHT LEVELING ECU ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C281157C14
1.417,0.375 1.969,0.625 0.552,0.25 2.198,1.219 2.25,0.177 2.25,0.177 2.469,0.177 true 2.354,1.24 2.542,0.531 2.542,0.531 2.792,0.531 true 0.156,0.115 0.469,0.313 0.313,0.198 10 false *a 2.844,0.438 3.365,0.635 0.521,0.198 10 false CANL 2.51,0.094 3.125,0.292 0.615,0.198 10 false CANH 1.583,0.406 1.896,0.604 0.313,0.198 10 false A67
*a Front view of wire harness connector
(to Headlight Leveling ECU Assembly)


Disconnect the A67 headlight leveling ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A67-6 (CANH) - A67-7 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (HEADLIGHT LEVELING ECU ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C281157C15
1.448,0.313 1.958,0.563 0.51,0.25 2.615,1.24 2.656,0.438 2.656,0.438 2.844,0.438 true 0.135,0.094 0.448,0.292 0.313,0.198 10 false *a 2.906,0.365 3.219,0.563 0.313,0.198 10 false E1 1.573,0.354 1.885,0.552 0.313,0.198 10 false A67
*a Front view of wire harness connector
(to Headlight Leveling ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A67-9 (E1) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.


c.
C281157C16
1.448,0.313 1.958,0.563 0.51,0.25 0.698,1.24 0.76,0.542 0.76,0.542 0.917,0.542 true 0.125,0.104 0.438,0.302 0.313,0.198 10 false *a 0.979,0.448 1.292,0.646 0.313,0.198 10 false IG 1.583,0.354 1.896,0.552 0.313,0.198 10 false A67
*a Front view of wire harness connector
(to Headlight Leveling ECU Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A67-1 (IG) - Body ground Ignition switch ON 11 to 14 V



Result:
Result
OK
NG



OK

REPLACE HEADLIGHT LEVELING ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)