ECUS OR SENSORS WHICH COMMUNICATE THROUGH CAN COMMUNICATION SYSTEM
V Bus
ECM
Combination meter assembly
Skid control ECU (brake actuator assembly)
Power steering ECU assembly
Steering sensor
Airbag sensor assembly
Main body ECU (multiplex network body ECU)
Air conditioning amplifier assembly
4WD ECU assembly*1
Network gateway ECU*2
Certification ECU (smart key ECU assembly)*3
Navigation receiver assembly*4
Radio and display receiver assembly*5
Clearance warning ECU assembly*6
Headlight leveling ECU assembly*7
Sub Bus 1*8
Main body ECU (multiplex network body ECU)
Outer mirror control ECU assembly (for driver side)*9
Outer mirror control ECU assembly (for front passenger side)*9
Position control ECU and switch assembly*9
Multiplex network door ECU
Sub Bus 2*2
Network gateway ECU
Driving support ECU assembly*10
Blind spot monitor sensor LH*11
Lane departure warning camera*12
Television camera assembly*13
Sub Bus 13*10
Driving support ECU assembly
Millimeter wave radar sensor assembly
*1: for AWD
*2: w/ Blind Spot Monitor System or Parking Assist Monitor System
*3: w/ Smart Entry and Start System
*4: for Navigation Receiver Type
*5: for Radio and Display Type
*6: w/ Toyota Parking Assist-sensor System
*7: w/ Automatic Headlight Beam Level Control System
*8: w/ Power Back Door System
*9: w/ Seat Position Memory System
*10: w/ Pre-crash Safety System
*11: w/ Blind Spot Monitor System
*12: w/ Lane Departure Alert System
*13: w/ Parking Assist Monitor System
CHECK FOR INSTALLED SYSTEMS (ECUS AND SENSORS) THAT ADOPT CAN COMMUNICATION
The systems (ECUs and sensors) that adopt CAN communication vary depending on the vehicle and optional equipment. Check which systems (ECUs and sensors) are installed on the vehicle.
The names of ECUs and sensors shown on the GTS display may differ from those shown in the DTC Table by ECU section that follows.
| ECU/Sensor Name | GTS Display | Applicability |
|---|---|---|
| ECM | ECM (Engine) | Installed on all vehicles |
| Combination meter assembly | Combination Meter | Installed on all vehicles |
| Power steering ECU assembly | Power Steering (EPS) | Installed on all vehicles |
| Main body ECU (multiplex network body ECU) | Main Body | Installed on all vehicles |
| Steering sensor | Spiral cable (Steering Angle Sensor) | Installed on all vehicles |
| Airbag sensor assembly | Airbag | Installed on all vehicles |
| Skid control ECU (brake actuator assembly) | Skid Control (ABS/VSC/TRAC) | Installed on all vehicles |
| Air conditioning amplifier assembly | Air Conditioning Amplifier | Installed on all vehicles |
| Certification ECU (smart key ECU assembly) | Certification (Smart) | Vehicles with smart entry and start system |
| Headlight leveling ECU assembly | Headlight swivel (AFS) | Vehicles with automatic headlight beam level control system |
| Network gateway ECU | CAN Gateway1 | Vehicles with blind spot monitor system or parking assist monitor system |
| Navigation receiver assembly | Display and Navigation (AVN1) | Vehicles with navigation receiver type |
| Radio and display receiver assembly | Display and Navigation (AVN1) | Vehicles with radio and display type |
| Outer mirror control ECU assembly (for front passenger side) | ·
Front Door RH/R-Mirror (FR-Door2/R-Miror) (for LHD) ·
Front Door LH/L-Mirror (FL-Door2/L-Miror) (for RHD) |
Vehicles with seat position memory system |
| Outer mirror control ECU assembly (for driver side) | ·
Front Door LH/L-Mirror (FL-Door2/L-Miror) (for LHD) ·
Front Door RH/R-Mirror (FR-Door2/R-Miror) (for RHD) |
Vehicles with seat position memory system |
| Position control ECU and switch assembly | D-Seat | Vehicles with seat position memory system |
| Driving support ECU assembly | Driving Support (Cruise Control-ACC) | Vehicles with pre-crash safety system |
| 4WD ECU assembly | Four Wheel Drive Control | Vehicles with AWD |
| Clearance warning ECU assembly | Clearance Warning (Clearance Sonar1) | Vehicles with Toyota parking assist-sensor system |
| Lane departure warning camera | Front Camera Module | Vehicles with lane departure alert system |
| Blind spot monitor sensor LH | Blind Spot Monitor Master | Vehicles with blind spot monitor system |
| Multiplex network door ECU | Back Door | Vehicles with power back door system |
| Television camera assembly | Parking Assist Monitor System3 | Vehicles with parking assist monitor system |
| Millimeter wave radar sensor assembly | - | Vehicles with pre-crash safety system |
CAN BUS CHECK
The ECUs and sensors that are properly connected to the CAN communication system can be displayed using the GTS.
Using the GTS, select the CAN Bus Check screen.
It may be possible to select buses that do not have ECUs or sensors from the bus selection pull-down menu. This is not a malfunction. (This occurs when optional devices are not on a sub bus that is monitored by a gateway function equipped ECU.)
In the bus selection pull down menu, all buses applicable to the model are displayed (e.g. LIN communication buses are also displayed). Therefore, refer to the wiring diagrams to check the names of sub buses for CAN communication.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>SYSTEM DIAGRAM
Different connection statuses are indicated by the background color of ECUs and sensors that are displayed.
| Bus Type | Background Color | Connection Status |
|---|---|---|
| V Bus | White | Communication has been normal since the start of the CAN bus check. |
| Yellow | Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication). | |
| Red | Communication was established at least once since the start of the CAN bus check, but communication is currently not occurring (unstable communication). | |
| Not displayed | Communication stop has continued since the start of the CAN bus check.*1 | |
| Sub Bus
(gateway function equipped ECU that does not have history of connected ECUs)*2 |
White | Communication has been normal since the start of the CAN bus check. |
| Yellow | Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication). | |
| Red | Communication was established at least once since the start of the CAN bus check, but communication is currently not occurring (unstable communication). | |
| Not displayed | Communication stop has continued since the start of the CAN bus check.*1 | |
| Sub Bus
(gateway function equipped ECU that has history of connected ECUs)*3 |
White | Communication has been normal since the start of the CAN bus check. |
| Yellow | Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication). | |
| Red | Currently not communicating (either of the following):
·
Communication stop has continued since the start of the CAN bus check. ·
Communication was established at least once since the start of the CAN bus check, but communication is currently not occurring. |
|
| Not displayed | Either of the following:
·
If a gateway function equipped ECU cannot communicate, the sub bus and ECUs connected to the sub bus will not be displayed. ·
If no ECUs are connected to the sub bus, "There is no system found on the Communication Bus" will be displayed. |
Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
*1: ECUs that are present in the vehicle but are not displayed on the CAN Bus Check screen.
*2: Gateway function equipped ECU that does not memorize the sub bus ECUs that are connected to it.
*3: Gateway function equipped ECU that memorizes the sub bus ECUs that are connected to it.
If none of the connected ECUs are displayed, or there is no response from the vehicle to the GTS, check the DLC3 branch and the V bus main bus lines for a malfunction.
Observe the connection response screen for approximately 2 minutes to check for a change in connection status of the connected ECUs and sensors.
If an open occurs in one of the lines of a CAN branch (except DLC3), output from the other branch line (the line that is not open) will be unstable and it may interfere with the response (display) of other ECUs and sensors.
If the connection status changes during the inspection, repair the open in the branch line of the ECU or sensor that does not respond (is not detected) and then perform the CAN bus check again.
HOW TO INTERPRET CAN BUS CHECK SCREEN
When a communication stop is currently occurring, the probable malfunctioning part can be determined from the CAN bus check and by using the following methods.
The following CAN bus wiring diagram is provided only as an example. This wiring diagram is different from the actual wiring diagram for this vehicle.
When a communication stop is currently occurring, it is easier to determine the probable malfunctioning part from the CAN bus check rather than from communication DTCs.
Wait for approximately 2 minutes after turning the ignition switch on (IG) (or simulate the driving conditions that enable the malfunction to be reproduced) and select "CAN Bus Check". Then observe the communication status of each ECU on the screen.
If a communication error of only 1 ECU or sensor is indicated on the CAN Bus Check screen, a communication stop of the ECU or sensor is suspected.
Example: Open in both CAN branch lines of ECU B on the V bus
| *a | V Bus | *b | Sub Bus |
| *c | Terminating Resistor | *d | Location of Malfunction |
| *e | Not displayed or background color changes to red or yellow | *f | CAN Bus Check Screen |
When there are communication stops, ECUs are present in the vehicle even though they are not displayed on the CAN Bus Check screen.
| *a | Background color periodically changes to yellow or red |
| *b | Not displayed or background color is yellow or red |
| *c | Not displayed |
If communication errors for multiple ECUs or sensors are indicated on the CAN Bus Check screen, then a communication stop of the ECU or sensor that shows a more serious communication stop (an ECU or a sensor which is not displayed) is suspected.
Example: Open in a CAN branch line for ECU D on the V bus
| Bus Type | Background Color | Connection Status |
|---|---|---|
| V Bus | White | Communication has been normal since the start of the CAN bus check. |
| Yellow | Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication). | |
| Red | Communication was established at least once since the start of the CAN bus check, but communication is currently not occurring (unstable communication). | |
| Not displayed | Communication stop has continued since the start of the CAN bus check.*1 | |
| Sub Bus
(gateway function equipped ECU that does not have history of connected ECUs)*2 |
White | Communication has been normal since the start of the CAN bus check. |
| Yellow | Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication). | |
| Red | Communication was established at least once since the start of the CAN bus check, but communication is currently not occurring (unstable communication). | |
| Not displayed | Communication stop has continued since the start of the CAN bus check.*1 | |
| Sub Bus
(gateway function equipped ECU that has history of connected ECUs)*3 |
White | Communication has been normal since the start of the CAN bus check. |
| Yellow | Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication). | |
| Red | Currently not communicating (either of the following):
·
Communication stop has continued since the start of the CAN bus check. ·
Communication was established at least once since the start of the CAN bus check, but communication is currently not occurring. |
|
| Not displayed | Either of the following:
·
If a gateway function equipped ECU cannot communicate, sub bus and ECUs connected to the sub bus will not be displayed. ·
If no ECUs are connected to the sub bus, "There is no system found on the Communication Bus" will be displayed. |
Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
*1: ECUs that are present in the vehicle but are not displayed on the CAN Bus Check screen.
*2: Gateway function equipped ECU that does not memorize the sub bus ECUs that are connected to it.
*3: Gateway function equipped ECU that memorizes the sub bus ECUs that are connected to it.
The example of the CAN Bus Check screen in the illustration shows the result of electrical noise on the CAN bus which is caused by an open in a CAN branch line of ECU D (output from the other branch line is unstable) and the communication of ECU C is also unstable. In addition, in this example, ECU C is equipped with a gateway function. Therefore, communication is also unstable between the sub bus ECUs of ECU C and the V bus.
The example in the illustration shows that ECU D is not displayed on the CAN Bus Check screen. This indicates a more significant communication stop. In this case, a communication stop of ECU D is suspected.
| *a | Not displayed or background color changes to red |
If a communication error is indicated on both the V bus and sub bus on the CAN Bus Check screen, suspect any communication stop displayed for the V bus first.
Example: Open in both CAN branch lines of ECU C on the V bus
In the CAN bus check, it is possible to confirm the communication status of ECUs connected to the V bus after connecting the GTS to the DLC3. As for sub buses, it is possible to confirm which sub bus connected ECUs can communicate with a gateway function equipped ECU on the V bus.
If a gateway function equipped ECU has a communication error, ECUs connected to the gateway function equipped ECU are also affected, and communication stops will be indicated.
The CAN Bus Check screen in the illustration shows that ECU C has a gateway function and a communication stop in ECU C is suspected.
| *a | Background color changes to red |
If the CAN Bus Check screen indicates a communication stop only in the sub bus, a communication stop in the sub bus is suspected.
Example: Open in both CAN branch lines of ECU G on the sub bus
A communication error in a sub bus does not affect the V bus or other buses.
When a gateway function equipped ECU has memorized the ECUs that are connected to the sub bus, if any of the ECUs connected to the gateway function equipped ECU has a communication error, the background color changes to yellow or red. (The displayed name will not disappear.)
If both of the V bus main bus lines are open, ECUs or sensors that are located farther away from the DLC3 than the open part will be displayed as a communication stop on the CAN Bus Check screen.
(In this case, ECU A and B are not displayed or their background color changes to red.)
| *a | V Bus | *b | Sub Bus |
| *c | Terminating Resistor | *d | Location of Malfunction |
| *e | Not displayed or background color is red | *f | CAN Bus Check Screen |
If a communication error occurs in an ECU, it is not displayed on the CAN Bus Check screen even though the ECU is present.
If both of the sub bus main bus lines are open, ECUs that are located farther away from the gateway function equipped ECU than the open part will be displayed as a communication stop on the CAN Bus Check screen.
(In this case, ECU I and J are not displayed or their background color changes to red.)
| *a | V Bus | *b | Sub Bus |
| *c | Terminating Resistor | *d | Location of Malfunction |
| *e | Not displayed or background color is red | *f | CAN Bus Check Screen |
| *g | Gateway Function Equipped ECU | - | - |
| *a | When any of the following malfunctions occur on the V bus |
| *b | When any of the following malfunctions occur on a sub bus |
| *c | Not displayed |
When any of the following malfunctions occur, CAN communication cannot be established and almost all ECUs and sensors on the bus show a communication error on the CAN Bus Check screen.
| Short between CAN lines (CANH and CANL) |
| Short between a CAN line (CANH or CANL) and +B |
| Short between a CAN line (CANH or CANL) and ground |
| Open in a CAN main bus line |
When a malfunction occurs on the V bus, almost all ECUs and sensors on the V bus and sub bus indicate a communication error (almost all ECUs are not displayed). As communication with the gateway function equipped ECU that is connected to the V bus stops, communication from the ECUs connected to the sub bus that is monitored by the gateway function equipped ECU also stops (these ECUs are not displayed).
When a malfunction occurs in a sub bus, almost all ECUs connected to the sub bus indicate a communication error.
A communication error in a sub bus does not affect the V bus or other buses.
The malfunctioning part can be determined by checking for a short circuit between CAN bus lines or between a CAN bus line and ground or +B short using an electrical tester.
HOW TO INTERPRET COMMUNICATION DTCS (DTCS THAT START WITH U)
If a CAN communication error cannot be reproduced, determine the suspected malfunctioning part using the DTCs stored in ECUs that are connected to the CAN buses by following the procedure below.
Communication DTCs (DTCs that start with U) indicate a communication error between the ECU that stores the DTC and the ECU that is indicated by the DTC.
If multiple ECUs store a communication DTC for a particular ECU, a communication stop of the ECU is suspected.
| *a | Items to be Checked | - | - |
This DTC table is from another model, and is only used here to show an example of DTCs that are output when there is an open in a CAN branch line for the main body ECU. This table does not show DTCs applicable to this vehicle.
Even though a DTC title may indicate a communication error with a specific ECU, the ECU name used in the DTC name on the GTS may differ depending on the ECU that stores the DTC. (Regarding output DTCs, refer to step 6 and the DTC chart for each ECU.)
As multiple ECUs indicate a communication stop with the main body ECU, the possibility of a communication stop of the main body ECU is high.
If almost all of the communication DTCs of an ECU are stored, a communication stop of the ECU is suspected.
| *a | Items to be Checked | - | - |
This DTC table is from another model, and is only used here to show an example of DTCs that are output when there is an open in a CAN branch line for the main body ECU. This table does not show DTCs applicable to this vehicle.
If almost all of the DTCs of the main body ECU are stored, the possibility of a communication stop of the main body ECU is high.
When a CAN communication error occurs, many DTCs are output. DTCs other than communication error DTCs (such as DTCs that start with C or B) and communication DTCs for the ABS system are important DTCs, however it may be easier to determine the malfunctioning part by examining the overall situation without considering these DTCs.
To help determine the part of the sub bus that has a communication error, prioritize the communication stop DTCs stored in the gateway function equipped ECU.
| *a | Items to be Checked | *b | ECM |
| *c | Gateway Function Equipped ECU | *d | Location of Malfunction |
| *e | V Bus | *f | Sub Bus |
This DTC table is from another model, and is only used here to show the ECUs connected to both a V bus and a sub bus. It shows DTCs output when there is an open in the main bus lines for the ECM on the sub bus. This table does not show DTCs applicable to this vehicle.
As gateway function equipped ECUs (sub bus monitor ECU) monitor signals from all ECUs that are connected to sub buses, gateway function equipped ECUs can detect ECUs with a communication stop more accurately.
When there is a communication stop for the gateway function equipped ECU (gateway), communication with ECUs connected to other buses such as the V bus stops. Therefore, communication DTCs for ECUs connected to other buses are also stored.
When any of the following malfunctions occurs, many DTCs are likely to be output from many ECUs. Because of this, it may be difficult to determine the probable malfunctioning part.
Short between CAN lines (CANH and CANL)
Short between a CAN line (CANH or CANL) and ground
Short between a CAN line (CANH or CANL) and +B
Open in a CAN branch line (CANH or CANL) of an ECU or sensor
Open in a CAN main bus line (CANH or CANL) between 2 ECUs that have a terminating resistor
DTC TABLE BY ECU
In the CAN communication system, the CAN communication DTCs of each ECU can be displayed using the GTS.
If CAN communication system DTCs are output, the malfunction cannot be determined only by the DTCs. Perform troubleshooting according to How to Proceed with Troubleshooting.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
If the system function temporarily returns to normal, DTCs may not be output again even though the following DTC check procedures are used.
ECM (for 1AR-FE) / GTS Display "Engine and ECT"
This ECU uses the CAN communication system for DTC communication.
*1: Refer to (U760E) Automatic Transaxle System.
Click hereDrivetrain>U760E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>U0100
*2: Refer to SFI System.
Click hereEngine / Hybrid System>1AR-FE ENGINE CONTROL>SFI SYSTEM>U0101
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0100*1 | Lost Communication with ECM / PCM "A" | The TCM does not receive data from the ECM for 1.25 seconds or more. | Both conditions are met:
·
The ignition switch is ON. ·
The power source voltage of the ECM is 10.5 V or more. |
Turn the ignition switch to ON and wait at least 1.25 seconds. | MIL illuminates. | DTC is stored until it is cleared using the GTS. |
| U0101*2 | Lost Communication with TCM | The ECM does not receive data from the TCM for 1.25 seconds or more. | Both conditions are met:
·
The ignition switch is ON. ·
The power source voltage of the ECM is 10.5 V or more. |
Turn the ignition switch to ON and wait at least 1.25 seconds. | MIL illuminates. | DTC is stored until it is cleared using the GTS. |
ECM (for 2GR-FE) / GTS Display "Engine"
This ECU uses the CAN communication system for DTC communication.
*: Refer to SFI System.
Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>U0101
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0101* | Lost Communication with TCM | The ECM does not receive data from the TCM for 1.25 seconds or more. | Both conditions are met:
·
The ignition switch is ON. ·
The power source voltage of the ECM is 10.5 V or more. |
Turn the ignition switch to ON and wait at least 1.25 seconds. | MIL illuminates. | DTC is stored until it is cleared using the GTS. |
TCM (for 2GR-FE) / GTS Display "ECT"
This ECU uses the CAN communication system for DTC communication.
*: Refer to (U660E or U660F) Automatic Transaxle System.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0100* | Lost Communication with ECM / PCM "A" | The TCM does not receive data from the ECM for 1.25 seconds or more. | Both conditions are met:
·
The ignition switch is ON. ·
The power source voltage of the ECM is 10.5 V or more. |
Turn the ignition switch to ON and wait at least 1.25 seconds. | MIL illuminates. | DTC is stored until it is cleared using the GTS. |
Skid Control ECU (Brake Actuator Assembly) / GTS Display "ABS/VSC/TRC"
This ECU uses the CAN communication system for DTC communication.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0073 | Control Module Communication Bus OFF | One of the following conditions is met:
·
Delayed reception of data from the steering sensor and airbag sensor assembly continues for 1 second or more. ·
The following condition occurs 10 times or more within 60 seconds: -
Delayed reception of data from the steering sensor and airbag sensor assembly occurs once or more within 5 seconds. ·
The following condition occurs 10 times in succession: -
The skid control ECU (brake actuator assembly) cannot send/receive data (bus off) once or more within 0.1 seconds. |
Both conditions are met:
·
The ignition switch is ON for 1 second or more. ·
The power source voltage of the skid control ECU (brake actuator assembly) (IG1 terminal voltage) is between 10 and 17.4 V. |
Turn the ignition switch to ON and wait at least 60 seconds. | ·
ABS warning light illuminates. ·
Slip indicator light illuminates. ·
Brake warning light illuminates. |
DTC is stored until it is cleared using the GTS. |
| U0100 | Lost Communication with ECM / PCM | The skid control ECU (brake actuator assembly) does not receive data from the ECM for 2 seconds or more. | All conditions are met:
·
The ignition switch is ON for 1 second or more. ·
Vehicle speed is 15 km/h (9 mph) or more. ·
The power source voltage of the skid control ECU (brake actuator assembly) (IG1 terminal voltage) is between 10 and 17.4 V. |
Turn the ignition switch to ON and drive the vehicle at a speed of 15 km/h (9 mph) or more for 3 seconds or more. | Slip indicator light illuminates. | DTC is stored until it is cleared using the GTS. |
| U0124 | Lost Communication with Lateral Acceleration Sensor Module | Either of the following conditions is met:
·
The skid control ECU (brake actuator assembly) does not receive data from the airbag sensor assembly for 1 second or more. ·
The following condition occurs 10 times or more within 60 seconds: -
The skid control ECU (brake actuator assembly) does not receive data from the airbag sensor assembly once or more within 5 seconds. |
Both conditions are met:
·
The ignition switch is ON for 1 second or more. ·
The power source voltage of the skid control ECU (brake actuator assembly) (IG1 terminal voltage) is between 10 and 17.4 V. |
Turn the ignition switch to ON and wait at least 60 seconds. | ·
ABS warning light illuminates. ·
Slip indicator light illuminates. |
DTC is stored until it is cleared using the GTS. |
| U0126 | Lost Communication with Steering Angle Sensor Module | Either of the following conditions is met:
·
The skid control ECU (brake actuator assembly) does not receive data from the steering sensor for 1 second or more. ·
The following condition occurs 10 times or more within 60 seconds: -
The skid control ECU (brake actuator assembly) does not receive data from the steering sensor once or more within 5 seconds. |
Both conditions are met:
·
The ignition switch is ON for 1 second or more. ·
The power source voltage of the skid control ECU (brake actuator assembly) (IG1 terminal voltage) is between 10 and 17.4 V. |
Turn the ignition switch to ON and wait at least 60 seconds. | Slip indicator light illuminates. | DTC is stored until it is cleared using the GTS. |
Power Steering ECU Assembly / GTS Display "EMPS"
This ECU uses the CAN communication system for DTC communication.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0100 | Lost Communication with ECM / PCM "A" | The power steering ECU assembly does not receive data from the ECM for 5 seconds or more. | All conditions are met:
·
The ignition switch is ON for 1 seconds or more. ·
Vehicle speed is 20 km/h (12 mph) or more. ·
The power source voltage of the power steering ECU assembly is 9 V or more. |
Drive the vehicle at a speed of 20 km/h (12 mph) or more for 6 seconds or more. | EPS warning light illuminates. | DTC remains stored only while malfunction is occurring. |
| U0129 | Lost Communication with Brake System Control Module | The power steering ECU assembly cannot receive data from the skid control ECU (brake actuator assembly) for 2.34 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 2 seconds or more. ·
The power source voltage of the power steering ECU assembly is 9 V or more. |
Turn the ignition switch to ON and wait at least 4.34 seconds. | EPS warning light illuminates. | DTC remains stored only while malfunction is occurring. |
Network Gateway ECU / GTS Display "Gateway"
This ECU uses the CAN communication system for DTC communication.
"Gateway" stores DTCs when a communication error is detected in sub bus 2.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0104 | Lost Communication with Cruise Control Module | The network gateway ECU does not receive data from the driving support ECU assembly for 10 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 11 seconds or more. ·
The power source voltage of the network gateway ECU is between 9.5 and 10.5 V. |
Turn the ignition switch to ON and wait at least 21 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0233 | Lost Communication with Blind Spot Monitor Master Module | The network gateway ECU does not receive data from the blind spot monitor sensor LH for 10 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 11 seconds or more. ·
The power source voltage of the network gateway ECU is between 9.5 and 10.5 V. |
Turn the ignition switch to ON and wait at least 21 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U023A | Lost Communication with Front Camera Module | The network gateway ECU does not receive data from the lane departure warning camera for 10 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 11 seconds or more. ·
The power source voltage of the network gateway ECU is between 9.5 and 10.5 V. |
Turn the ignition switch to ON and wait at least 21 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0265 | Lost Communication with Parking Assist Monitor Module | The network gateway ECU does not receive data from the television camera assembly for 10 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 11 seconds or more. ·
The power source voltage of the network gateway ECU is between 9.5 and 10.5 V. |
Turn the ignition switch to ON and wait at least 21 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U1002 | Lost Communication with Gateway Module (Network Gateway ECU) | The network gateway ECU detects communication errors between itself and the driving support ECU assembly, blind spot monitor sensor LH, lane departure warning camera and television camera assembly. | Both conditions are met:
·
The ignition switch is ON for 11 seconds or more. ·
The power source voltage of the network gateway ECU is between 9.5 and 10.5 V. |
Turn the ignition switch to ON and wait at least 21 seconds. | - | DTC is stored until it is cleared using the GTS. |
Main Body ECU (Multiplex Network Body ECU) / GTS Display "Main Body"
This ECU uses the CAN communication system for DTC communication.
*1: for LHD
*2: for RHD
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0100 | Lost Communication with ECM / PCM "A" | The main body ECU (multiplex network body ECU) does not receive data from the ECM for 10 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more elapse. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or more. |
Turn the ignition switch to ON and wait at least 20 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0101 | Lost Communication with TCM | The main body ECU (multiplex network body ECU) does not receive data from the TCM for 10 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more elapse. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or more. |
Turn the ignition switch to ON and wait at least 20 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0120 | Lost Communication with Starter / Generator Control Module | The main body ECU (multiplex network body ECU) does not receive data from the certification ECU (smart key ECU assembly) for 10 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more elapse. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or more. |
Turn the ignition switch to ON and wait at least 20 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0151 | Lost Communication with Restraints Control Module | The main body ECU (multiplex network body ECU) does not receive data from the airbag sensor assembly for 10 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more elapse. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or more. |
Turn the ignition switch to ON and wait at least 20 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0155 | Lost Communication with Instrument Panel Cluster (IPC) Control Module | The main body ECU (multiplex network body ECU) does not receive data from the combination meter assembly for 10 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more elapse. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or more. |
Turn the ignition switch to ON and wait at least 20 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0199 | Lost Communication with ''Door Control Module A'' | ·
The main body ECU (multiplex network body ECU) does not receive data from the outer mirror control ECU assembly (for front passenger side) for 10 seconds or more. *1 ·
The main body ECU (multiplex network body ECU) does not receive data from the outer mirror control ECU assembly (for driver side) for 10 seconds or more.*2 |
Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more elapse. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or more. |
Turn the ignition switch to ON and wait at least 20 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0200 | Lost Communication with ''Door Control Module B'' | ·
The main body ECU (multiplex network body ECU) does not receive data from the outer mirror control ECU assembly (for driver side) for 10 seconds or more.*1 ·
The main body ECU (multiplex network body ECU) does not receive data from the outer mirror control ECU assembly (for front passenger side) for 10 seconds or more. *2 |
Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more elapse. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or more. |
Turn the ignition switch to ON and wait at least 20 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0208 | Lost Communication with ''Seat Control Module A'' | The main body ECU (multiplex network body ECU) does not receive data from the position control ECU and switch assembly for 10 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more elapse. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or more. |
Turn the ignition switch to ON and wait at least 20 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0230 | Lost Communication with Rear Gate Module | The main body ECU (multiplex network body ECU) does not receive data from the multiplex network door ECU for 10 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more elapse. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or more. |
Turn the ignition switch to ON and wait at least 20 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U023A | Lost Communication with Image Processing Module "A" | The main body ECU (multiplex network body ECU) does not receive data from the lane departure warning camera for 10 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more elapse. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or more. |
Turn the ignition switch to ON and wait at least 20 seconds. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0327 | Software Incompatibility with Vehicle Security Control Module | The main body ECU (multiplex network body ECU) does not receive data from the certification ECU (smart key ECU assembly) for 10 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more elapse. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or more. |
Turn the ignition switch to ON and wait at least 20 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U1002 | Lost Communication with Gateway Module (Main body) | The main body ECU (multiplex network body ECU) detects communication errors between itself and the position control ECU and switch assembly, outer mirror control ECU assembly (for front passenger side), outer mirror control ECU assembly (for driver side) and multiplex network door ECU. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more elapse. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or more. |
Turn the ignition switch to ON and wait at least 20 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U1126 | Lost Communication with Parking Assist Monitor Module | The main body ECU (multiplex network body ECU) does not receive data from the television camera assembly for 10 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more elapse. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or more. |
Turn the ignition switch to ON and wait at least 20 seconds. | - | DTC is stored until it is cleared using the GTS. |
Certification ECU (Smart Key ECU Assembly) / GTS Display "Entry&Start"
This ECU uses the CAN communication system for DTC communication.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0100 | Lost Communication with ECM / PCM | The certification ECU (smart key ECU assembly) does not receive data from the ECM for 10 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more elapse. ·
The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or more. |
Turn the ignition switch to ON and wait at least 20 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0142 | Lost Communication with Main Body ECU | The certification ECU (smart key ECU assembly) does not receive data from the main body ECU (multiplex network body ECU) for 10 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more elapse. ·
The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or more. |
Turn the ignition switch to ON and wait at least 20 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0155 | Lost Communication with Combination Meter | The certification ECU (smart key ECU assembly) does not receive data from the combination meter assembly for 10 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more elapse. ·
The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or more. |
Turn the ignition switch to ON and wait at least 20 seconds. | - | DTC is stored until it is cleared using the GTS. |
Certification ECU (Smart Key ECU Assembly) / GTS Display "Power Source Control"
This ECU uses the CAN communication system for DTC communication.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0100 | Lost Communication with ECM / PCM | The certification ECU (smart key ECU assembly) does not receive data from the ECM for 3.1 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 1 second or more. ·
The power source voltage of the certification ECU (smart key ECU assembly) is 9.5 V or more. |
Turn the ignition switch to ON and wait at least 4.1 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0140 | Lost Communication with Main Body ECU | The certification ECU (smart key ECU assembly) does not receive data from the main body ECU (multiplex network body ECU) for 3 seconds or more. | Both conditions are met:
·
The ignition switch is ON. ·
The power source voltage of the certification ECU (smart key ECU assembly) is 9.5 V or more. |
Turn the ignition switch to ON and wait at least 3 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0155 | Lost Communication with Combination Meter | The certification ECU (smart key ECU assembly) does not receive data from the combination meter assembly for 3.1 seconds or more. | Both conditions are met:
·
The ignition switch is ON. ·
The power source voltage of the certification ECU (smart key ECU assembly) is 9.5 V or more. |
Turn the ignition switch to ON and wait at least 3.1 seconds. | - | DTC is stored until it is cleared using the GTS. |
Certification ECU (Smart Key ECU Assembly) / GTS Display "Starting Control"
This ECU uses the CAN communication system for DTC communication.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0100 | Lost Communication with ECM / PCM | The certification ECU (smart key ECU assembly) does not receive data from the ECM for 2 seconds or more. | Both conditions are met:
·
The ignition switch is ON. ·
The power source voltage of the certification ECU (smart key ECU assembly) is 10.5 V or more. |
Turn the ignition switch to ON and wait at least 2 seconds. | - | DTC remains stored only while malfunction is occurring. |
Headlight Leveling ECU Assembly / GTS Display "HL AutoLeveling"
This ECU uses the CAN communication system for DTC communication.
*: The headlight leveling ECU assembly stores this DTC if an internal error related to the CAN communication system is detected.
Click hereVehicle Exterior>LIGHTING (EXT)>AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM>U1000
This ECU uses the CAN communication system for DTC communication.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0100 | Lost Communication with ECM / PCM "A" | The headlight leveling ECU assembly does not receive data from the ECM for 10 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 3 seconds or more. ·
The power source voltage of the headlight leveling ECU assembly is 9.5 V or more. |
Turn the ignition switch to ON and wait at least 13 seconds. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0129 | Lost Communication with Brake System Control Module | The headlight leveling ECU assembly does not receive data from the skid control ECU (brake actuator assembly) for 10 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 3 seconds or more. ·
The power source voltage of the headlight leveling ECU assembly is 9.5 V or more. |
Turn the ignition switch to ON and wait at least 13 seconds. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0142 | Lost Communication with Body Control Module "B" | The headlight leveling ECU assembly does not receive data from the main body ECU (multiplex network body ECU) for 10 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 3 seconds or more. ·
The power source voltage of the headlight leveling ECU assembly is 9.5 V or more. |
Turn the ignition switch to ON and wait at least 13 seconds. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U1000* | CAN Communication Failure (Message Registry) | When the ignition switch is turned on (IG), a CAN communication malfunction is detected. | The ignition switch is ON. | Turn the ignition switch to ON. | Displays messages on the multi-information display. | DTC remains stored only while malfunction is occurring. |
Television Camera Assembly / GTS Display "IPA/Parking Assist Monitor"
This ECU uses the CAN communication system for DTC communication.
*1: The television camera assembly stores this DTC if an internal error related to the CAN communication system is detected.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>U1000
*2: for Navigation Receiver Type
*3: for Radio and Display Type
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0100 | Lost Communication with ECM / PCM "A" | The television camera assembly does not receive data from the ECM for 11 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 3 seconds or more. ·
The power source voltage of the television camera assembly is 5.5 V or more. |
Turn the ignition switch to ON and wait at least 14 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0126 | Lost Communication with Steering Angle Sensor Module | The television camera assembly does not receive data from the steering sensor for 11 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 3 seconds or more. ·
The power source voltage of the television camera assembly is 5.5 V or more. |
Turn the ignition switch to ON and wait at least 14 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0129 | Lost Communication with Brake System Control Module | The television camera assembly does not receive data from the skid control ECU (brake actuator assembly) for 11 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 3 seconds or more. ·
The power source voltage of the television camera assembly is 5.5 V or more. |
Turn the ignition switch to ON and wait at least 14 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0131 | Lost Communication with Power Steering Control Module | The television camera assembly does not receive data from the power steering ECU assembly for 11 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 3 seconds or more. ·
The power source voltage of the television camera assembly is 5.5 V or more. |
Turn the ignition switch to ON and wait at least 14 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0140 | Lost Communication with Body Control Module | The television camera assembly does not receive data from the main body ECU (multiplex network body ECU) for 11 seconds or more. | Both conditions are met:
·
The ignition switch is ACC for 3 seconds or more. ·
The power source voltage of the television camera assembly is 5.5 V or more. |
Turn the ignition switch to ON and wait at least 14 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0163 | Lost Communication with Navigation Control Module | ·
The television camera assembly does not receive data from the navigation receiver assembly for 11 seconds or more.*2 ·
The television camera assembly does not receive data from the radio and display receiver assembly for 11 seconds or more.*3 |
Both conditions are met:
·
The ignition switch is ACC for 3 seconds or more. ·
The power source voltage of the television camera assembly is 5.5 V or more. |
Turn the ignition switch to ON and wait at least 14 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U1000*1 | CAN Communication Failure (Message Registry) | When the ignition switch is turned on (IG), a CAN communication malfunction is detected. | The ignition switch is ON. | Turn the ignition switch to ON. | - | DTC remains stored only while malfunction is occurring. |
| U1110 | Lost Communication with Clearance Sonar Module | The television camera assembly does not receive data from the clearance warning ECU assembly for 11 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 3 seconds or more. ·
The power source voltage of the television camera assembly is 5.5 V or more. |
Turn the ignition switch to ON and wait at least 14 seconds. | - | DTC is stored until it is cleared using the GTS. |
Air Conditioning Amplifier Assembly / GTS Display "Air Conditioner"
This ECU uses the CAN communication system for DTC communication.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0100 | Lost Communication with ECM | The air conditioning amplifier assembly does not receive data from the ECM for 5 seconds or more. | Both conditions are met:
·
The ignition switch is ON. ·
The power source voltage of the air conditioning amplifier assembly is 10 V or more. |
Turn the ignition switch to ON and wait at least 5 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0131 | Lost Communication with Electric Power Steering ECU | The air conditioning amplifier assembly does not receive data from the power steering ECU assembly for 5 seconds or more. | Both conditions are met:
·
The ignition switch is ON. ·
The power source voltage of the air conditioning amplifier assembly is 10 V or more. |
Turn the ignition switch to ON and wait at least 5 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0142 | Lost Communication with Main Body ECU | The air conditioning amplifier assembly does not receive data from the main body ECU (multiplex network body ECU) for 5 seconds or more. | Both conditions are met:
·
The ignition switch is ON. ·
The power source voltage of the air conditioning amplifier assembly is 10 V or more. |
Turn the ignition switch to ON and wait at least 5 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0155 | Lost Communication with Combination Meter | The air conditioning amplifier assembly does not receive data from the combination meter assembly for 5 seconds or more. | Both conditions are met:
·
The ignition switch is ON. ·
The power source voltage of the air conditioning amplifier assembly is 10 V or more. |
Turn the ignition switch to ON and wait at least 5 seconds. | - | DTC is stored until it is cleared using the GTS. |
Navigation Receiver Assembly / GTS Display "Navigation System"
This ECU uses the CAN communication system for DTC communication.
*1: w/ Toyota Parking Assist-sensor System
*2: w/o Toyota Parking Assist-sensor System
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0073 | Sending Malfunction (Navigation to APGS) | The navigation receiver assembly does not send/receive data for 5 seconds or more. | Both conditions are met:
·
The ignition switch is ON. ·
The power source voltage of the navigation receiver assembly is 9.5 V or more. |
Turn the ignition switch to ON and wait at least 6 seconds. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0100 | Engine ECU Communication | Either of the following conditions is met:
·
The navigation receiver assembly does not receive data from the ECM for 12 seconds or more.*1 ·
The navigation receiver assembly does not receive data from the ECM for 4 seconds or more.*2 |
Both conditions are met:
·
The ignition switch is ON for 1 second or more. ·
The power source voltage of the navigation receiver assembly is 9.5 V or more. |
·
Turn the ignition switch to ON and wait at least 13 seconds.*1 ·
Turn the ignition switch to ON and wait at least 5 seconds.*2 |
- | DTC is stored until it is cleared using the GTS. |
| U0140 | Lost Communication with Body Control Module | The navigation receiver assembly does not receive data from the main body ECU (multiplex network body ECU) for 10 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 1 second or more. ·
The power source voltage of the navigation receiver assembly is 9.5 V or more. |
Turn the ignition switch to ON and wait at least 11 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0155 | Meter ECU Communication | The navigation receiver assembly does not receive data from the combination meter assembly for 30 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 1 second or more. ·
The power source voltage of the navigation receiver assembly is 9.5 V or more. |
Turn the ignition switch to ON and wait at least 31 seconds. | - | DTC is stored until it is cleared using the GTS. |
Radio and Display Receiver Assembly / GTS Display "Navigation System"
This ECU uses the CAN communication system for DTC communication.
*1: w/ Toyota Parking Assist-sensor System
*2: w/o Toyota Parking Assist-sensor System
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0073 | Sending Malfunction (Navigation to APGS) | The radio and display receiver assembly does not send/receive data for 5 seconds or more. | Both conditions are met:
·
The ignition switch is ON. ·
The power source voltage of the radio and display receiver assembly is 9.5 V or more. |
Turn the ignition switch to ON and wait at least 6 seconds. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0100 | Engine ECU Communication | Either of the following conditions is met:
·
The radio and display receiver assembly does not receive data from the ECM for 12 seconds or more.*1 ·
The radio and display receiver assembly does not receive data from the ECM for 4 seconds or more.*2 |
Both conditions are met:
·
The ignition switch is ON for 1 second or more. ·
The power source voltage of the radio and display receiver assembly is 9.5 V or more. |
·
Turn the ignition switch to ON and wait at least 13 seconds.*1 ·
Turn the ignition switch to ON and wait at least 5 seconds.*2 |
- | DTC is stored until it is cleared using the GTS. |
| U0140 | Lost Communication with Body Control Module | The radio and display receiver assembly does not receive data from the main body ECU (multiplex network body ECU) for 10 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 1 second or more. ·
The power source voltage of the radio and display receiver assembly is 9.5 V or more. |
Turn the ignition switch to ON and wait at least 11 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0155 | Meter ECU Communication | The radio and display receiver assembly does not receive data from the combination meter assembly for 30 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 1 second or more. ·
The power source voltage of the radio and display receiver assembly is 9.5 V or more. |
Turn the ignition switch to ON and wait at least 31 seconds. | - | DTC is stored until it is cleared using the GTS. |
Combination Meter Assembly / GTS Display "Combination Meter"
This ECU uses the CAN communication system for DTC communication.
*1: for Navigation Receiver Type
*2: for Radio and Display Type
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0100 | Lost Communication with ECM / PCM "A" | The combination meter assembly does not receive data from the ECM for 3 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 1 second or more. ·
The power source voltage of the combination meter assembly is 11.5 V or more. |
Turn the ignition switch to ON and wait at least 4 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0129 | Lost Communication with Brake System Control Module | The combination meter assembly does not receive data from the skid control ECU (brake actuator assembly) for 3 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 1 second or more. ·
The power source voltage of the combination meter assembly is 11.5 V or more. |
Turn the ignition switch to ON and wait at least 4 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0131 | Lost Communication with Power Steering Control Module | The combination meter assembly does not receive data from the power steering ECU assembly for 3 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 1 second or more. ·
The power source voltage of the combination meter assembly is 11.5 V or more. |
Turn the ignition switch to ON and wait at least 4 seconds. | EPS warning light illuminates. | DTC is stored until it is cleared using the GTS. |
| U0142 | Lost Communication with Body Control Module "B" | The combination meter assembly does not receive data from the main body ECU (multiplex network body ECU) for 10 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 1 second or more. ·
The power source voltage of the combination meter assembly is 11.5 V or more. |
Turn the ignition switch to ON and wait at least 11 seconds. | Tire pressure warning light illuminates. | DTC is stored until it is cleared using the GTS. |
| U0151 | Lost Communication with Restraints Control Module | The combination meter assembly does not receive data from the airbag sensor assembly for 10 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 1 second or more. ·
The power source voltage of the combination meter assembly is 11.5 V or more. |
Turn the ignition switch to ON and wait at least 11 seconds. | ·
SRS warning light illuminates. ·
Displays messages on the multi-information display. |
DTC is stored until it is cleared using the GTS. |
| U0163 | Lost Communication with Navigation Control Module | ·
The combination meter assembly does not receive data from the navigation receiver assembly for 3 seconds or more.*1 ·
The combination meter assembly does not receive data from the radio and display receiver assembly for 3 seconds or more.*2 |
Both conditions are met:
·
The ignition switch is ON for 1 second or more. ·
The power source voltage of the combination meter assembly is 11.5 V or more. |
Turn the ignition switch to ON and wait at least 4 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0182 | Lost Communication with Lighting Control Module Front | The combination meter assembly does not receive data from the headlight leveling ECU assembly for 10 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 1 second or more. ·
The power source voltage of the combination meter assembly is 11.5 V or more. |
Turn the ignition switch to ON and wait at least 11 seconds. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U023A | Lost Communication with Front Camera Module | The combination meter assembly does not receive data from the lane departure warning camera for 10 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 1 second or more. ·
The power source voltage of the combination meter assembly is 11.5 V or more. |
Turn the ignition switch to ON and wait at least 11 seconds. | ·
Lane departure alert indicator light illuminates. ·
Displays messages on the multi-information display. |
DTC is stored until it is cleared using the GTS. |
| U1104 | Lost Communication with Driving Support ECU | The combination meter assembly does not receive data from the driving support ECU assembly for 10 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 1 second or more. ·
The power source voltage of the combination meter assembly is 11.5 V or more. |
Turn the ignition switch to ON and wait at least 11 seconds. | ·
PCS warning light flashes. ·
Displays messages on the multi-information display. |
DTC is stored until it is cleared using the GTS. |
Outer Mirror Control ECU Assembly (for Front Passenger Side) / GTS Display "Mirror R" (for LHD), "Mirror L" (for RHD)
This ECU uses the CAN communication system for DTC communication.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0142 | Lost Communication with Body Control Module ''B'' | The outer mirror control ECU assembly (for front passenger side) does not receive data from the main body ECU (multiplex network body ECU) for 10 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected. ·
The power source voltage of the outer mirror control ECU assembly (for front passenger side) is 10 V or more. |
Turn the ignition switch to ON and wait at least 10 seconds. | - | DTC is stored until it is cleared using the GTS. |
Outer Mirror Control ECU Assembly (for Driver Side) / GTS Display "Mirror L" (for LHD), "Mirror R" (for RHD)
This ECU uses the CAN communication system for DTC communication.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0142 | Lost Communication with Body Control Module ''B'' | The outer mirror control ECU assembly (for driver side) does not receive data from the main body ECU (multiplex network body ECU) for 10 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected. ·
The power source voltage of the outer mirror control ECU assembly (for driver side) is 10 V or more. |
Turn the ignition switch to ON and wait at least 10 seconds. | - | DTC is stored until it is cleared using the GTS. |
Multiplex Network Door ECU / GTS Display "Back Door"
This ECU uses the CAN communication system for DTC communication.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0101 | Lost Communication with TCM | The multiplex network door ECU does not receive data from the ECM for 10 seconds or more. | Both conditions are met:
·
The ignition switch is ON. ·
The power source voltage of the multiplex network door ECU is 10.5 V or more. |
Turn the ignition switch to ON and wait at least 10 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0122 | Lost Communication with Vehicle Dynamics Control Module | The multiplex network door ECU does not receive data from the skid control ECU (brake actuator assembly) for 10 seconds or more. | Both conditions are met:
·
The ignition switch is ON. ·
The power source voltage of the multiplex network door ECU is 10.5 V or more. |
Turn the ignition switch to ON and wait at least 10 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0142 | Lost Communication with Body Control Module "B" | The multiplex network door ECU does not receive data from the main body ECU (multiplex network body ECU) for 10 seconds or more. | Both conditions are met:
·
The ignition switch is ON. ·
The power source voltage of the multiplex network door ECU is 10.5 V or more. |
Turn the ignition switch to ON and wait at least 10 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0155 | Lost Communication with Instrument Panel Cluster (IPC) Control Module | The multiplex network door ECU does not receive data from the combination meter assembly for 10 seconds or more. | Both conditions are met:
·
The ignition switch is ON. ·
The power source voltage of the multiplex network door ECU is 10.5 V or more. |
Turn the ignition switch to ON and wait at least 10 seconds. | - | DTC is stored until it is cleared using the GTS. |
ECM / GTS Display "Radar Cruise"
This ECU uses the CAN communication system for DTC communication.
*1: Dynamic radar cruise control system DTC
*2: If U0235 or U1102 is output alone, the CAN communication is normal (Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>U0235 for U0235, Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>U1102 for U1102).
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0100*1 | Lost Communication with ECM / PCM "A" | Either condition is met:
·
The ECM detects a communication error signal (from the ECM to the driving support ECU assembly) for 4 seconds or more. ·
The ECM detects a communication error signal (from the ECM to the skid control ECU (brake actuator assembly) for 2 seconds or more. |
The radar cruise control system (vehicle control mode) is operating. | Allow the radar cruise control system (vehicle control mode) to operate for 4 seconds or more. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0122*1 | Lost Communication with Vehicle Dynamics Control Module | Either condition is met:
·
The ECM detects a communication error signal (from the skid control ECU (brake actuator assembly) to the driving support ECU assembly) for 4 seconds or more. ·
The ECM does not receive data from the skid control ECU (brake actuator assembly) for 3 seconds or more. |
The radar cruise control system (vehicle control mode) is operating. | Allow the radar cruise control system (vehicle control mode) to operate for 4 seconds or more. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0123*1 | Lost Communication with Yaw Rate Sensor Module | The ECM detects a communication error signal (from the airbag sensor assembly to the driving support ECU assembly) for 1 second or more. | The radar cruise control system (vehicle control mode) is operating. | Allow the radar cruise control system (vehicle control mode) to operate for 1 second or more. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0126*1 | Lost Communication with Steering Angle Sensor Module | The ECM detects a communication error signal (from the steering sensor to the driving support ECU assembly) for 4 seconds or more. | The radar cruise control system (vehicle control mode) is operating. | Allow the radar cruise control system (vehicle control mode) to operate for 4 seconds or more. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0235*2 | Lost Communication with Cruise Control Front Distance Range Sensor | The ECM detects a communication error signal (from the millimeter wave radar sensor assembly to the driving support ECU assembly) for 1 second or more. | The radar cruise control system (vehicle control mode) is operating. | Allow the radar cruise control system (vehicle control mode) to operate for 1 second or more. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U1102*2 | Lost Communication with Radar Sensor | The ECM detects a communication error signal (from the driving support ECU assembly to the millimeter wave radar sensor) for 1 second or more. | The radar cruise control system (vehicle control mode) is operating. | Allow the radar cruise control system (vehicle control mode) to operate for 1 second or more. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U1104*1 | Lost Communication with Driving Support ECU | The ECM does not receive data from the driving support ECU assembly for 1 second or more. | The radar cruise control system (vehicle control mode) is operating. | Allow the radar cruise control system (vehicle control mode) to operate for 1 second or more. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
Driving Support ECU Assembly / GTS Display "Pre-Crash 2"
This ECU uses the CAN communication system for DTC communication.
*: Refer to Pre-crash Safety System.
Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>U0235
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0125 | Lost Communication with Yaw Rate Sensor Module | The driving support ECU assembly does not receive data from the airbag sensor assembly for 0.772 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 3 seconds or more. ·
The power source voltage of the driving support ECU assembly is 10 V or more. |
Turn the ignition switch to ON and wait at least 3.772 seconds. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0126 | Lost Communication with Steering Angle Sensor Module | The driving support ECU assembly does not receive data from the steering sensor for 3.76 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 1 second or more. ·
The power source voltage of the driving support ECU assembly is 10 V or more. |
Turn the ignition switch to ON and wait at least 4.76 seconds. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0129 | Lost Communication with Brake System Control Module | The driving support ECU assembly does not receive data from the skid control ECU (brake actuator assembly) for 5.24 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 2 seconds or more. ·
The power source voltage of the driving support ECU assembly is 10 V or more. |
Turn the ignition switch to ON and wait at least 7.24 seconds. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0142 | Lost Communication with Body Control Module "B" | The driving support ECU assembly does not receive data from the main body ECU (multiplex network body ECU) for 14.2 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 1 second or more. ·
The power source voltage of the driving support ECU assembly is 10 V or more. |
Turn the ignition switch to ON and wait at least 15.2 seconds. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0235* | Lost Communication with Cruise Control Front Distance Range Sensor | The driving support ECU assembly does not receive data from the millimeter wave radar sensor assembly for 0.65 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 1 second or more. ·
The power source voltage of the driving support ECU assembly is 10 V or more. |
Turn the ignition switch to ON and wait at least 1.65 seconds. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U1002 | Lost Communication with Gateway Module | The driving support ECU assembly does not receive data from ECU with a sub bus 13 connection record for 0.5 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 1 second or more. ·
The power source voltage of the driving support ECU assembly is 10 V or more. |
Turn the ignition switch to ON and wait at least 1.5 seconds. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U1104* | Lost Communication with Driving Support ECU | The ECM, skid control ECU (brake actuator assembly) or millimeter wave radar sensor assembly does not receive data from the driving support ECU assembly for 4.5 seconds or more. | The engine switch is on (IG) for 2 seconds or more. | Turn the ignition switch to ON and wait at least 6.5 seconds. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
Clearance Warning ECU Assembly / GTS Display "Clearance Sonar"
This ECU uses the CAN communication system for DTC communication.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0101 | Lost Communication with TCM | The clearance warning ECU assembly does not receive data from the ECM for 5 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 5 seconds or more. ·
The power source voltage of the clearance warning ECU assembly is 10.2 V or more. |
Turn the ignition switch to ON and wait at least 10 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0155 | Lost Communication with Instrument Panel Cluster (IPC) Control Module | The clearance warning ECU assembly does not receive data from the combination meter assembly for 5 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 5 seconds or more. ·
The power source voltage of the clearance warning ECU assembly is 10.2 V or more. |
Turn the ignition switch to ON and wait at least 10 seconds. | - | DTC is stored until it is cleared using the GTS. |
4WD ECU Assembly / GTS Display "Four Wheel Drive"
This ECU uses the CAN communication system for DTC communication.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0073 | Control Module Communication Bus Off | The 4WD ECU assembly keeps sending data to an ECU or a sensor for 5 seconds or more because a receive completion signal is not received. | Both conditions are met:
·
The ignition switch is ON for 1 second or more. ·
The power source voltage of the 4WD ECU assembly is 10 V or more. |
Turn the ignition switch to ON and wait at least 6 seconds. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0100 | Lost Communication with ECM / PCM "A" | The 4WD ECU assembly does not receive data from the ECM for 3.5 seconds or more. | All conditions are met:
·
The ignition switch is ON for 1 second or more. ·
Vehicle speed is 60 km/h (37 mph) or more. ·
The power source voltage of the 4WD ECU assembly is 10 V or more. |
Drive the vehicle at a speed of 60 km/h (37 mph) or more for 4.5 seconds or more. | - | DTC is stored until it is cleared using the GTS. |
| U0126 | Lost Communication with Steering Angle Sensor Module | Either of the following conditions is met:
·
The 4WD ECU assembly does not receive data from the steering sensor for 1 second or more. ·
condition occurs 10 times or more within 60 seconds: -
The 4WD ECU assembly does not receive data from the steering sensor once or more within 5 seconds. |
Both conditions are met:
·
The ignition switch is ON for 1 second or more. ·
The power source voltage of the 4WD ECU assembly is 10 V or more. |
Turn the ignition switch to ON and wait at least 60 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0129 | Lost Communication with Brake System Control Module | The 4WD ECU assembly does not receive data from the skid control ECU (brake actuator assembly) for 8 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 2 seconds or more. ·
The power source voltage of the 4WD ECU assembly is 10 V or more. |
Turn the ignition switch to ON and wait at least 10 seconds. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
Blind Spot Monitor Sensor LH / GTS Display "Blind Spot Monitor Master"
This ECU uses the CAN communication system for DTC communication.
*: If U0232 or U1331 is output alone, the CAN communication is normal (Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>U0232 for U0232, Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>U1331 for U1331)
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0100 | Lost Communication with ECM / PCM "A" | The blind spot monitor sensor LH does not receive data from the ECM for 10.84 seconds or more. | All conditions are met:
·
The ignition switch is ON for 1 second or more. ·
Blind spot monitor main switch is on. ·
The power source voltage of the blind spot monitor sensor LH is 10 V or more. |
Turn the ignition switch to ON, turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch) and wait at least 11.84 seconds. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0126 | Lost Communication with Steering Angle Sensor Module | The blind spot monitor sensor LH does not receive data from the steering sensor for 10.68 seconds or more. | All conditions are met:
·
The ignition switch is ON for 1 second or more. ·
Blind spot monitor main switch is on. ·
The power source voltage of the blind spot monitor sensor LH is 10 V or more. |
Turn the ignition switch to ON, turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch) and wait at least 11.68 seconds. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0129 | Lost Communication with Brake System Control Module | The blind spot monitor sensor LH does not receive data from the skid control ECU (brake actuator assembly) for 2.334 seconds or more. | All conditions are met:
·
The ignition switch is ON for 1 second or more. ·
Blind spot monitor main switch is on. ·
The power source voltage of the blind spot monitor sensor LH is 10 V or more. |
Turn the ignition switch to ON, turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch) and wait at least 3.334 seconds. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0142 | Lost Communication with Body Control Module "B" | The blind spot monitor sensor LH does not receive data from the main body ECU (multiplex network body ECU) for 10.6 seconds or more. | All conditions are met:
·
The ignition switch is ON for 1 second or more. ·
Blind spot monitor main switch is on. ·
The power source voltage of the blind spot monitor sensor LH is 10 V or more. |
Turn the ignition switch to ON, turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch) and wait at least 11.6 seconds. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0232* | Lost Communication with Blind Spot Monitor Slave Module | The blind spot monitor sensor LH does not receive data from the blind spot monitor sensor RH for 10.6 seconds or more. | All conditions are met:
·
The ignition switch is ON for 1 second or more. ·
Blind spot monitor main switch is on. ·
The power source voltage of the blind spot monitor sensor LH is 10 V or more. |
Turn the ignition switch to ON, turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch) and wait at least 11.6 seconds. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U1331* | Software Incompatibility with Body Control Module "B" | Destination information of the main body ECU (multiplex network body ECU) and blind spot monitor sensor do not match. | All conditions are met:
·
The ignition switch is ON for 1 second or more. ·
Blind spot monitor main switch is on. ·
The power source voltage of the blind spot monitor sensor LH is 10 V or more. |
Turn the ignition switch to ON, turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch) and wait at least 1 second. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
Lane Departure Warning Camera / GTS Display "Lane Departure Alert"
This ECU uses the CAN communication system for DTC communication.
*: The lane departure warning camera monitors its internal condition, when an internal malfunction is detected, the lane departure warning camera stores U1000 and cancels lane departure alert system control.
Click hereEngine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM>U1000
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0101 | Lost Communication with TCM | The lane departure warning camera does not receive data from the ECM for 5 seconds or more. | All conditions are met:
·
The ignition switch is ON for 2 seconds or more. ·
Vehicle speed is 1 km/h (1 mph) or more. ·
The power source voltage of the lane departure warning camera is 10 V or more. |
Drive the vehicle at a speed of 1 km/h (1 mph) or more for 7 seconds or more. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0123 | Lost Communication with Yaw Rate Sensor Module | The lane departure warning camera does not receive data from the airbag sensor assembly for 5 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 2 seconds or more. ·
Vehicle speed is 1 km/h (1 mph) or more. ·
The power source voltage of the lane departure warning camera is 10 V or more. |
Drive the vehicle at a speed of 1 km/h (1 mph) or more for 7 seconds or more. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0129 | Lost Communication with Brake System Control Module | The lane departure warning camera does not receive data from the skid control ECU (brake actuator assembly) for 5 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 2 seconds or more. ·
The power source voltage of the lane departure warning camera is 10 V or more. |
Turn the ignition switch to ON and wait at least 7 seconds. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0142 | Lost Communication with Body Control Module "B" | The lane departure warning camera does not receive data from the main body ECU (multiplex network body ECU) for 5 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 2 seconds or more. ·
The power source voltage of the lane departure warning camera is 10 V or more. |
Turn the ignition switch to ON and wait at least 7 seconds. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0155 | Lost Communication with Instrument Panel Cluster (IPC) Control Module | The lane departure warning camera does not receive data from the combination meter assembly for 50 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 2 seconds or more. ·
The power source voltage of the lane departure warning camera is 10 V or more. |
Turn the ignition switch to ON and wait at least 52 seconds. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U1000* | CAN Communication Failure (Message Registry) | When the ignition switch is turned on (IG), a CAN communication malfunction is detected. | The ignition switch is ON. | Turn the ignition switch to ON. | Displays messages on the multi-information display. | DTC remains stored only while malfunction is occurring. |
Steering Sensor
The steering sensor is connected to the CAN communication system, but the steering sensor does not store or output CAN communication DTCs.
Position Control ECU and Switch Assembly
The position control ECU and switch assembly is connected to the CAN communication system, but the position control ECU and switch assembly does not store or output CAN communication DTCs.
Airbag Sensor Assembly
The airbag sensor assembly is connected to the CAN communication system, but the airbag sensor assembly does not store or output CAN communication DTCs.
Millimeter Wave Radar Sensor Assembly
The millimeter wave radar sensor assembly is connected to the CAN communication system, but the millimeter wave radar sensor assembly does not store or output CAN communication DTCs.
DTC COMBINATION TABLE (OPEN IN CAN BRANCH OF V BUS, PAST COMMUNICATION ERROR)
Regarding a past communication error of an ECU and sensor connected to the V bus (in this case, normal is displayed when performing the CAN bus check, but communication DTCs are output), the probable CAN branch that had a malfunction can be determined based on the following DTC combination table.
Based on the table below and DTCs output from ECUs connected via CAN communication, the probable part for which communication stop occurred can be determined.
Regarding an open in a CAN branch and a communication stop that is currently occurring, the malfunctioning part can be confirmed easily by performing the CAN bus check using the GTS because the ECU or sensor connected to the CAN branch does not respond (the ECU or sensor name will not be displayed on the screen).
If an open in a CAN main bus line, a short between the CAN bus lines (CANH and CANL) or a +B or ground short in the CAN bus occurs, DTCs of almost all ECUs (or sensors) on the CAN bus may be output, or a message indicating a communication error may be displayed on the GTS screen. In this case, check the resistance of the CAN bus (steps 7 to 9) first.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
If an open occurs in just one of the lines of a CAN branch, DTCs which are not related to malfunctioning parts may be output (DTCs may be displayed randomly), or a message indicating a communication error may be displayed.
X: DTC is likely to be output.
▲: DTC is unlikely to be output.
-: DTC is not output.
*1: DTC U0073 may be stored when communication is lost.
*2: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
○: DTC is output.
-: DTC is not output.
*1: DTC U0073 may be stored when communication is lost.
*2: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
X: DTC is likely to be output.
▲: DTC is unlikely to be output.
-: DTC is not output.
*1: DTC U0073 may be stored when communication is lost.
*2: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
○: DTC is output.
-: DTC is not output.
*1: DTC U0073 may be stored when communication is lost.
*2: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
| - | Trouble Mode (CAN Bus Lines Short Circuit or Short to GND) | ||||
|---|---|---|---|---|---|
| V Bus | |||||
| Output ECU | Output DTC | CANH to CANL | CANH to Ground Short | CANL to Ground Short | |
| V Bus | Airbag Sensor Assembly | - | - | - | - |
| Air Conditioning Amplifier Assembly | U0100 | ○ | ○ | ○ | |
| U0131 | ○ | ○ | ○ | ||
| U0142 | ○ | ○ | ○ | ||
| U0155 | ○ | ○ | ○ | ||
| Headlight Leveling ECU Assembly | U0100 | ○ | ○ | ○ | |
| U0129 | ○ | ○ | ○ | ||
| U0142 | ○ | ○ | ○ | ||
| Radio and Display Receiver Assembly*1 | U0100 | ○ | ○ | ○ | |
| U0140 | ○ | ○ | ○ | ||
| U0155 | ○ | ○ | ○ | ||
| Main Body ECU (Multiplex Network Body ECU)*2 | U0100 | ○ | ○ | ○ | |
| U0101 | ○ | ○ | ○ | ||
| U0120 | ○ | ○ | ○ | ||
| U0151 | ○ | ○ | ○ | ||
| U0155 | ○ | ○ | ○ | ||
| U023A | ○ | ○ | ○ | ||
| U0327 | ○ | ○ | ○ | ||
| U1126 | ○ | ○ | ○ | ||
| Network Gateway ECU*2 | - | - | - | - | |
| ECM (for 1AR-FE) | - | - | - | - | |
| ECM (for 2GR-FE) | - | - | - | - | |
| V Bus | Power Steering ECU Assembly | U0100 | ○ | ○ | ○ |
| U0129 | ○ | ○ | ○ | ||
| 4WD ECU Assembly*1 | U0100 | ○ | ○ | ○ | |
| U0126 | ○ | ○ | ○ | ||
| U0129 | ○ | ○ | ○ | ||
| Certification ECU (Smart Key ECU Assembly)
(Entry function) |
U0100 | ○ | ○ | ○ | |
| U0142 | ○ | ○ | ○ | ||
| U0155 | ○ | ○ | ○ | ||
| Certification ECU (Smart Key ECU Assembly)
(Power source switching function) |
U0100 | ○ | ○ | ○ | |
| U0140 | ○ | ○ | ○ | ||
| U0155 | ○ | ○ | ○ | ||
| Certification ECU (Smart Key ECU Assembly)
(Start function) |
U0100 | ○ | ○ | ○ | |
| Combination Meter Assembly | U0100 | ○ | ○ | ○ | |
| U0129 | ○ | ○ | ○ | ||
| U0131 | ○ | ○ | ○ | ||
| U0142 | ○ | ○ | ○ | ||
| U0151 | ○ | ○ | ○ | ||
| U0163 | ○ | ○ | ○ | ||
| U0182 | ○ | ○ | ○ | ||
| U023A | ○ | ○ | ○ | ||
| U1104 | ○ | ○ | ○ | ||
| Steering Sensor | - | - | - | - | |
| Skid Control ECU (Brake Actuator Assembly) | U0073 | ○ | ○ | ○ | |
| U0100 | ○ | ○ | ○ | ||
| U0124 | ○ | ○ | ○ | ||
| U0126 | ○ | ○ | ○ | ||
| Sub Bus 2 | Blind Spot Monitor Sensor LH | U0100 | ○ | ○ | ○ |
| U0126 | ○ | ○ | ○ | ||
| U0129 | ○ | ○ | ○ | ||
| U0142 | ○ | ○ | ○ | ||
| Television Camera Assembly | U0100 | ○ | ○ | ○ | |
| U0126 | ○ | ○ | ○ | ||
| U0129 | ○ | ○ | ○ | ||
| U0131 | ○ | ○ | ○ | ||
| U0140 | ○ | ○ | ○ | ||
| U0163 | ○ | ○ | ○ | ||
| Network Gateway ECU*2 | U0233 | - | - | - | |
| U023A | - | - | - | ||
| U0265 | - | - | - | ||
| U1002 | - | - | - | ||
| Lane Departure Warning Camera*1 | U0101 | ○ | ○ | ○ | |
| U0123 | ○ | ○ | ○ | ||
| U0129 | ○ | ○ | ○ | ||
| U0142 | ○ | ○ | ○ | ||
| U0155 | ○ | ○ | ○ | ||
| Sub Bus 1 | Main Body ECU (Multiplex Network Body ECU)*2 | U0199 | - | - | - |
| U0200 | - | - | - | ||
| U0208 | - | - | - | ||
| U0230 | - | - | - | ||
| U1002 | - | - | - | ||
| Multiplex Network Door ECU | U0101 | ○ | ○ | ○ | |
| U0122 | ○ | ○ | ○ | ||
| U0142 | - | - | - | ||
| U0155 | ○ | ○ | ○ | ||
| Outer Mirror Control ECU Assembly (for Driver Side) | U0142 | - | - | - | |
| Outer Mirror Control ECU Assembly (for Front Passenger Side) | U0142 | - | - | - | |
| Position Control ECU and Switch Assembly | - | - | - | - | |
○: DTC is output.
-: DTC is not output.
*1: DTC U0073 may be stored when communication is lost.
*2: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
X: DTC is likely to be output.
▲: DTC is unlikely to be output.
-: DTC is not output.
*1: DTC U0073 may be stored when communication is lost.
*2: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
○: DTC is output.
▲: DTC is unlikely to be output.
-: DTC is not output.
*1: DTC U0073 may be stored when communication is lost.
*2: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
X: DTC is likely to be output.
▲: DTC is unlikely to be output.
-: DTC is not output.
*1: DTC U0073 may be stored when communication is lost.
*2: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
○: DTC is output.
-: DTC is not output.
*1: DTC U0073 may be stored when communication is lost.
*2: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
| - | Trouble Mode (CAN Bus Lines Short Circuit or Short to GND) | ||||
|---|---|---|---|---|---|
| V Bus | |||||
| Output ECU | Output DTC | CANH to CANL | CANH to Ground Short | CANL to Ground Short | |
| V Bus | Airbag Sensor Assembly | - | - | - | - |
| Air Conditioning Amplifier Assembly | U0100 | ○ | ○ | ○ | |
| U0131 | ○ | ○ | ○ | ||
| U0142 | ○ | ○ | ○ | ||
| U0155 | ○ | ○ | ○ | ||
| Headlight Leveling ECU Assembly | U0100 | ○ | ○ | ○ | |
| U0129 | ○ | ○ | ○ | ||
| U0142 | ○ | ○ | ○ | ||
| Navigation Receiver Assembly*1 | U0100 | ○ | ○ | ○ | |
| U0140 | ○ | ○ | ○ | ||
| U0155 | ○ | ○ | ○ | ||
| Radio and Display Receiver Assembly*1 | U0100 | ○ | ○ | ○ | |
| U0140 | ○ | ○ | ○ | ||
| U0155 | ○ | ○ | ○ | ||
| Main Body ECU (Multiplex Network Body ECU)*2 | U0100 | ○ | ○ | ○ | |
| U0101 | ○ | ○ | ○ | ||
| U0120 | ○ | ○ | ○ | ||
| U0151 | ○ | ○ | ○ | ||
| U0155 | ○ | ○ | ○ | ||
| U023A | ○ | ○ | ○ | ||
| U0327 | ○ | ○ | ○ | ||
| U1126 | ○ | ○ | ○ | ||
| Clearance Warning ECU Assembly | U0101 | ○ | ○ | ○ | |
| U0155 | ○ | ○ | ○ | ||
| Network Gateway ECU*2 | - | - | - | - | |
| ECM (for 1AR-FE) | - | - | - | - | |
| ECM (for 2GR-FE) | - | - | - | - | |
| V Bus | ECM
(Radar cruise function) |
U0100 | ○ | ○ | ○ |
| U0122 | ○ | ○ | ○ | ||
| U0123 | ○ | ○ | ○ | ||
| U0126 | ○ | ○ | ○ | ||
| U1104 | ○ | ○ | ○ | ||
| Power Steering ECU Assembly | U0100 | ○ | ○ | ○ | |
| U0129 | ○ | ○ | ○ | ||
| 4WD ECU Assembly*1 | U0100 | ○ | ○ | ○ | |
| U0126 | ○ | ○ | ○ | ||
| U0129 | ○ | ○ | ○ | ||
| Certification ECU (Smart Key ECU Assembly)
(Entry function) |
U0100 | ○ | ○ | ○ | |
| U0142 | ○ | ○ | ○ | ||
| U0155 | ○ | ○ | ○ | ||
| Certification ECU (Smart Key ECU Assembly)
(Power source switching function) |
U0100 | ○ | ○ | ○ | |
| U0140 | ○ | ○ | ○ | ||
| U0155 | ○ | ○ | ○ | ||
| Certification ECU (Smart Key ECU Assembly)
(Start function) |
U0100 | ○ | ○ | ○ | |
| Combination Meter Assembly | U0100 | ○ | ○ | ○ | |
| U0129 | ○ | ○ | ○ | ||
| U0131 | ○ | ○ | ○ | ||
| U0142 | ○ | ○ | ○ | ||
| U0151 | ○ | ○ | ○ | ||
| U0163 | ○ | ○ | ○ | ||
| U0182 | ○ | ○ | ○ | ||
| U023A | ○ | ○ | ○ | ||
| U1104 | ○ | ○ | ○ | ||
| Steering Sensor | - | - | - | - | |
| Skid Control ECU (Brake Actuator Assembly) | U0073 | ○ | ○ | ○ | |
| U0100 | ○ | ○ | ○ | ||
| U0124 | ○ | ○ | ○ | ||
| U0126 | ○ | ○ | ○ | ||
| Sub Bus 2 | Blind Spot Monitor Sensor LH | U0100 | ○ | ○ | ○ |
| U0126 | ○ | ○ | ○ | ||
| U0129 | ○ | ○ | ○ | ||
| U0142 | ○ | ○ | ○ | ||
| Television Camera Assembly | U0100 | ○ | ○ | ○ | |
| U0126 | ○ | ○ | ○ | ||
| U0129 | ○ | ○ | ○ | ||
| U0131 | ○ | ○ | ○ | ||
| U0140 | ○ | ○ | ○ | ||
| U0163 | ○ | ○ | ○ | ||
| U1110 | ○ | ○ | ○ | ||
| Network Gateway ECU*2 | U0104 | - | - | - | |
| U0233 | - | - | - | ||
| U023A | - | - | - | ||
| U0265 | - | - | - | ||
| U1002 | - | - | - | ||
| Sub Bus 2 | Driving Support ECU Assembly
(Pre-crash Safety System) |
U0125 | ○ | ○ | ○ |
| U0126 | ○ | ○ | ○ | ||
| U0129 | ○ | ○ | ○ | ||
| U0142 | ○ | ○ | ○ | ||
| Lane Departure Warning Camera*1 | U0101 | ○ | ○ | ○ | |
| U0123 | ○ | ○ | ○ | ||
| U0129 | ○ | ○ | ○ | ||
| U0142 | ○ | ○ | ○ | ||
| U0155 | ○ | ○ | ○ | ||
| Sub Bus 1 | Main Body ECU (Multiplex Network Body ECU)*2 | U0199 | - | - | - |
| U0200 | - | - | - | ||
| U0208 | - | - | - | ||
| U0230 | - | - | - | ||
| U1002 | - | - | - | ||
| Multiplex Network Door ECU | U0101 | ○ | ○ | ○ | |
| U0122 | ○ | ○ | ○ | ||
| U0142 | ○ | ○ | ○ | ||
| U0155 | ○ | ○ | ○ | ||
| Outer Mirror Control ECU Assembly (for Front Passenger Side) | U0142 | - | - | - | |
| Outer Mirror Control ECU Assembly (for Driver Side) | U0142 | - | - | - | |
| Position Control ECU and Switch Assembly | - | - | - | - | |
○: DTC is output.
-: DTC is not output.
*1: DTC U0073 may be stored when communication is lost.
*2: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
DTC COMBINATION TABLE (OPEN IN CAN BRANCH OF SUB BUS 1, PAST COMMUNICATION ERROR)
Regarding a past communication error of an ECU and sensor connected to sub bus 1 (in this case, normal is displayed when performing the CAN bus check, but communication DTCs are output), determine the part that had a malfunction based on DTCs output from the main body ECU (multiplex network body ECU).
As gateway function equipped ECUs (sub bus monitor ECUs) monitor signals from all ECUs that are connected to sub buses, gateway function equipped ECUs can detect ECUs with a communication stop more accurately.
DTCs output from ECUs other than the main body ECU (multiplex network body ECU) (gateway function equipped ECU) are shown only as a reference.
Regarding a communication stop that is currently occurring in sub bus 1, the malfunctioning part can be confirmed easily by performing the CAN bus check using the GTS.
If an open occurs in just one of the lines of a CAN branch, DTCs which are not related to malfunctioning parts may be output (DTCs may be displayed randomly), or a message indicating a communication error may be displayed.
X: DTC is likely to be output.
▲: DTC is unlikely to be output.
-: DTC is not output.
*1: DTC U0073 may be stored when communication is lost.
*2: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
○: DTC is output.
-: DTC is not output.
*1: DTC U0073 may be stored when communication is lost.
*2: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
X: DTC is likely to be output.
▲: DTC is unlikely to be output.
-: DTC is not output.
*1: DTC U0073 may be stored when communication is lost.
*2: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
○: DTC is output.
-: DTC is not output.
*1: DTC U0073 may be stored when communication is lost.
*2: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
| - | Trouble Mode (CAN Bus Lines Short Circuit or Short to GND) | ||||
|---|---|---|---|---|---|
| Sub Bus 1 | |||||
| Output ECU | Output DTC | CANH to CANL | CANH to Ground Short | CANL to Ground Short | |
| V Bus | Airbag Sensor Assembly | - | - | - | - |
| Air Conditioning Amplifier Assembly | U0100 | - | - | - | |
| U0131 | - | - | - | ||
| U0142 | - | - | - | ||
| U0155 | - | - | - | ||
| Headlight Leveling ECU Assembly | U0100 | - | - | - | |
| U0129 | - | - | - | ||
| U0142 | - | - | - | ||
| Radio and Display Receiver Assembly*1 | U0100 | - | - | - | |
| U0140 | - | - | - | ||
| U0155 | - | - | - | ||
| Main Body ECU (Multiplex Network Body ECU)*2 | U0100 | - | - | - | |
| U0101 | - | - | - | ||
| U0120 | - | - | - | ||
| U0151 | - | - | - | ||
| U0155 | - | - | - | ||
| U023A | - | - | - | ||
| U0327 | - | - | - | ||
| U1126 | - | - | - | ||
| Network Gateway ECU*2 | - | - | - | - | |
| ECM (for 1AR-FE) | - | - | - | - | |
| ECM (for 2GR-FE) | - | - | - | - | |
| Power Steering ECU Assembly | U0100 | - | - | - | |
| U0129 | - | - | - | ||
| 4WD ECU Assembly*1 | U0100 | - | - | - | |
| U0126 | - | - | - | ||
| U0129 | - | - | - | ||
| Certification ECU (Smart Key ECU Assembly)
(Entry function) |
U0100 | - | - | - | |
| U0142 | - | - | - | ||
| U0155 | - | - | - | ||
| V Bus | Certification ECU (Smart Key ECU Assembly)
(Power source switching function) |
U0100 | - | - | - |
| U0140 | - | - | - | ||
| U0155 | - | - | - | ||
| Certification ECU (Smart Key ECU Assembly)
(Start function) |
U0100 | - | - | - | |
| Combination Meter Assembly | U0100 | - | - | - | |
| U0129 | - | - | - | ||
| U0131 | - | - | - | ||
| U0142 | - | - | - | ||
| U0151 | - | - | - | ||
| U0163 | - | - | - | ||
| U0182 | - | - | - | ||
| U023A | - | - | - | ||
| U1104 | - | - | - | ||
| Steering Sensor | - | - | - | - | |
| Skid Control ECU (Brake Actuator Assembly) | U0073 | - | - | - | |
| U0100 | - | - | - | ||
| U0124 | - | - | - | ||
| U0126 | - | - | - | ||
| Sub Bus 2 | Blind Spot Monitor Sensor LH | U0100 | - | - | - |
| U0126 | - | - | - | ||
| U0129 | - | - | - | ||
| U0142 | - | - | - | ||
| Television Camera Assembly | U0100 | - | - | - | |
| U0126 | - | - | - | ||
| U0129 | - | - | - | ||
| U0131 | - | - | - | ||
| U0140 | - | - | - | ||
| U0163 | - | - | - | ||
| Network Gateway ECU*2 | U0233 | - | - | - | |
| U023A | - | - | - | ||
| U0265 | - | - | - | ||
| U1002 | - | - | - | ||
| Lane Departure Warning Camera*1 | U0101 | - | - | - | |
| U0123 | - | - | - | ||
| U0129 | - | - | - | ||
| U0142 | - | - | - | ||
| U0155 | - | - | - | ||
| Sub Bus 1 | Main Body ECU (Multiplex Network Body ECU)*2 | U0199 | ○ | ○ | ○ |
| U0200 | ○ | ○ | ○ | ||
| U0208 | ○ | ○ | ○ | ||
| U0230 | ○ | ○ | ○ | ||
| U1002 | ○ | ○ | ○ | ||
| Multiplex Network Door ECU | U0101 | ○ | ○ | ○ | |
| U0122 | ○ | ○ | ○ | ||
| U0142 | ○ | ○ | ○ | ||
| U0155 | ○ | ○ | ○ | ||
| Sub Bus 1 | Outer Mirror Control ECU Assembly (for Driver Side) | U0142 | ○ | ○ | ○ |
| Outer Mirror Control ECU Assembly (for Front Passenger Side) | U0142 | ○ | ○ | ○ | |
| Position Control ECU and Switch Assembly | - | - | - | - | |
○: DTC is output.
-: DTC is not output.
*1: DTC U0073 may be stored when communication is lost.
*2: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
X: DTC is likely to be output.
▲: DTC is unlikely to be output.
-: DTC is not output.
*1: DTC U0073 may be stored when communication is lost.
*2: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
○: DTC is output.
-: DTC is not output.
*1: DTC U0073 may be stored when communication is lost.
*2: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
X: DTC is likely to be output.
▲: DTC is unlikely to be output.
-: DTC is not output.
*1: DTC U0073 may be stored when communication is lost.
*2: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
○: DTC is output.
-: DTC is not output.
*1: DTC U0073 may be stored when communication is lost.
*2: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
| - | Trouble Mode (CAN Bus Lines Short Circuit or Short to GND) | ||||
|---|---|---|---|---|---|
| Sub Bus 1 | |||||
| Output ECU | Output DTC | CANH to CANL | CANH to Ground Short | CANL to Ground Short | |
| V Bus | Airbag Sensor Assembly | - | - | - | - |
| Air Conditioning Amplifier Assembly | U0100 | - | - | - | |
| U0131 | - | - | - | ||
| U0142 | - | - | - | ||
| U0155 | - | - | - | ||
| Headlight Leveling ECU Assembly | U0100 | - | - | - | |
| U0129 | - | - | - | ||
| U0142 | - | - | - | ||
| Navigation Receiver Assembly*1 | U0100 | - | - | - | |
| U0140 | - | - | - | ||
| U0155 | - | - | - | ||
| Radio and Display Receiver Assembly*1 | U0100 | - | - | - | |
| U0140 | - | - | - | ||
| U0155 | - | - | - | ||
| Main Body ECU (Multiplex Network Body ECU)*2 | U0100 | - | - | - | |
| U0101 | - | - | - | ||
| U0120 | - | - | - | ||
| U0151 | - | - | - | ||
| U0155 | - | - | - | ||
| U023A | - | - | - | ||
| U0327 | - | - | - | ||
| U1126 | - | - | - | ||
| Clearance Warning ECU Assembly | U0101 | - | - | - | |
| U0155 | - | - | - | ||
| Network Gateway ECU*2 | - | - | - | - | |
| ECM (for 1AR-FE) | - | - | - | - | |
| ECM (for 2GR-FE) | - | - | - | - | |
| ECM
(Radar cruise function) |
U0100 | - | - | - | |
| U0122 | - | - | - | ||
| U0123 | - | - | - | ||
| U0126 | - | - | - | ||
| U1104 | - | - | - | ||
| Power Steering ECU Assembly | U0100 | - | - | - | |
| U0129 | - | - | - | ||
| 4WD ECU Assembly*1 | U0100 | - | - | - | |
| U0126 | - | - | - | ||
| U0129 | - | - | - | ||
| V Bus | Certification ECU (Smart Key ECU Assembly)
(Entry function) |
U0100 | - | - | - |
| U0142 | - | - | - | ||
| U0155 | - | - | - | ||
| Certification ECU (Smart Key ECU Assembly)
(Power source switching function) |
U0100 | - | - | - | |
| U0140 | - | - | - | ||
| U0155 | - | - | - | ||
| Certification ECU (Smart Key ECU Assembly)
(Start function) |
U0100 | - | - | - | |
| Combination Meter Assembly | U0100 | - | - | - | |
| U0129 | - | - | - | ||
| U0131 | - | - | - | ||
| U0142 | - | - | - | ||
| U0151 | - | - | - | ||
| U0163 | - | - | - | ||
| U0182 | - | - | - | ||
| U023A | - | - | - | ||
| U1104 | - | - | - | ||
| Steering Sensor | - | - | - | - | |
| Skid Control ECU (Brake Actuator Assembly) | U0073 | - | - | - | |
| U0100 | - | - | - | ||
| U0124 | - | - | - | ||
| U0126 | - | - | - | ||
| Sub Bus 2 | Blind Spot Monitor Sensor LH | U0100 | - | - | - |
| U0126 | - | - | - | ||
| U0129 | - | - | - | ||
| U0142 | - | - | - | ||
| Television Camera Assembly | U0100 | - | - | - | |
| U0126 | - | - | - | ||
| U0129 | - | - | - | ||
| U0131 | - | - | - | ||
| U0140 | - | - | - | ||
| U0163 | - | - | - | ||
| U1110 | - | - | - | ||
| Network Gateway ECU*2 | U0104 | - | - | - | |
| U0233 | - | - | - | ||
| U023A | - | - | - | ||
| U0265 | - | - | - | ||
| U1002 | - | - | - | ||
| Driving Support ECU Assembly
(Pre-crash Safety System) |
U0125 | - | - | - | |
| U0126 | - | - | - | ||
| U0129 | - | - | - | ||
| U0142 | - | - | - | ||
| Lane Departure Warning Camera*1 | U0101 | - | - | - | |
| U0123 | - | - | - | ||
| U0129 | - | - | - | ||
| U0142 | - | - | - | ||
| U0155 | - | - | - | ||
| Sub Bus 1 | Main Body ECU (Multiplex Network Body ECU)*2 | U0199 | ○ | ○ | ○ |
| U0200 | ○ | ○ | ○ | ||
| U0208 | ○ | ○ | ○ | ||
| U0230 | ○ | ○ | ○ | ||
| U1002 | ○ | ○ | ○ | ||
| Multiplex Network Door ECU | U0101 | ○ | ○ | ○ | |
| U0122 | ○ | ○ | ○ | ||
| U0142 | ○ | ○ | ○ | ||
| U0155 | ○ | ○ | ○ | ||
| Outer Mirror Control ECU Assembly (for Front Passenger Side) | U0142 | ○ | ○ | ○ | |
| Outer Mirror Control ECU Assembly (for Driver Side) | U0142 | ○ | ○ | ○ | |
| Position Control ECU and Switch Assembly | - | - | - | - | |
○: DTC is output.
-: DTC is not output.
*1: DTC U0073 may be stored when communication is lost.
*2: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
DTC COMBINATION TABLE (OPEN IN CAN BRANCH OF SUB BUS 2, PAST COMMUNICATION ERROR)
Regarding a past communication error of an ECU and sensor connected to sub bus 2 (in this case, normal is displayed when performing the CAN bus check, but communication DTCs are output), determine the part that had a malfunction based on DTCs output from the network gateway ECU.
As gateway function equipped ECUs (sub bus monitor ECUs) monitor signals from all ECUs that are connected to sub buses, gateway function equipped ECUs can detect ECUs with a communication stop more accurately.
DTCs output from ECUs other than the network gateway ECU (gateway function equipped ECU) are shown only as a reference.
Regarding a communication stop that is currently occurring in sub bus 2, the malfunctioning part can be confirmed easily by performing the CAN bus check using the GTS.
If an open occurs in just one of the lines of a CAN branch, DTCs which are not related to malfunctioning parts may be output (DTCs may be displayed randomly), or a message indicating a communication error may be displayed.
X: DTC is likely to be output.
▲: DTC is unlikely to be output.
-: DTC is not output.
*1: DTC U0073 may be stored when communication is lost.
*2: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
○: DTC is output.
-: DTC is not output.
*1: DTC U0073 may be stored when communication is lost.
*2: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
X: DTC is likely to be output.
▲: DTC is unlikely to be output.
-: DTC is not output.
*1: DTC U0073 may be stored when communication is lost.
*2: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
○: DTC is output.
-: DTC is not output.
*1: DTC U0073 may be stored when communication is lost.
*2: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
| - | Trouble Mode (CAN Bus Lines Short Circuit or Short to GND) | ||||
|---|---|---|---|---|---|
| Sub Bus 2 | |||||
| Output ECU | Output DTC | CANH to CANL | CANH to Ground Short | CANL to Ground Short | |
| V Bus | Airbag Sensor Assembly | - | - | - | - |
| Air Conditioning Amplifier Assembly | U0100 | - | - | - | |
| U0131 | - | - | - | ||
| U0142 | - | - | - | ||
| U0155 | - | - | - | ||
| Headlight Leveling ECU Assembly | U0100 | - | - | - | |
| U0129 | - | - | - | ||
| U0142 | - | - | - | ||
| Radio and Display Receiver Assembly*1 | U0100 | - | - | - | |
| U0140 | - | - | - | ||
| U0155 | - | - | - | ||
| Main Body ECU (Multiplex Network Body ECU)*2 | U0100 | - | - | - | |
| U0101 | - | - | - | ||
| U0120 | - | - | - | ||
| U0151 | - | - | - | ||
| U0155 | - | - | - | ||
| U023A | ○ | ○ | ○ | ||
| U0327 | - | - | - | ||
| U1126 | ○ | ○ | ○ | ||
| Network Gateway ECU*2 | - | - | - | - | |
| ECM (for 1AR-FE) | - | - | - | - | |
| ECM (for 2GR-FE) | - | - | - | - | |
| Power Steering ECU Assembly | U0100 | - | - | - | |
| U0129 | - | - | - | ||
| 4WD ECU Assembly*1 | U0100 | - | - | - | |
| U0126 | - | - | - | ||
| U0129 | - | - | - | ||
| Certification ECU (Smart Key ECU Assembly)
(Entry function) |
U0100 | - | - | - | |
| U0142 | - | - | - | ||
| U0155 | - | - | - | ||
| V Bus | Certification ECU (Smart Key ECU Assembly)
(Power source switching function) |
U0100 | - | - | - |
| U0140 | - | - | - | ||
| U0155 | - | - | - | ||
| Certification ECU (Smart Key ECU Assembly)
(Start function) |
U0100 | - | - | - | |
| Combination Meter Assembly | U0100 | - | - | - | |
| U0129 | - | - | - | ||
| U0131 | - | - | - | ||
| U0142 | - | - | - | ||
| U0151 | - | - | - | ||
| U0163 | - | - | - | ||
| U0182 | - | - | - | ||
| U023A | ○ | ○ | ○ | ||
| U1104 | ○ | ○ | ○ | ||
| Steering Sensor | - | - | - | - | |
| Skid Control ECU (Brake Actuator Assembly) | U0073 | - | - | - | |
| U0100 | - | - | - | ||
| U0124 | - | - | - | ||
| U0126 | - | - | - | ||
| Sub Bus 2 | Blind Spot Monitor Sensor LH | U0100 | ○ | ○ | ○ |
| U0126 | ○ | ○ | ○ | ||
| U0129 | ○ | ○ | ○ | ||
| U0142 | ○ | ○ | ○ | ||
| Television Camera Assembly | U0100 | ○ | ○ | ○ | |
| U0126 | ○ | ○ | ○ | ||
| U0129 | ○ | ○ | ○ | ||
| U0131 | ○ | ○ | ○ | ||
| U0140 | ○ | ○ | ○ | ||
| U0163 | ○ | ○ | ○ | ||
| Network Gateway ECU*2 | U0233 | ○ | ○ | ○ | |
| U023A | ○ | ○ | ○ | ||
| U0265 | ○ | ○ | ○ | ||
| U1002 | ○ | ○ | ○ | ||
| Lane Departure Warning Camera*1 | U0101 | ○ | ○ | ○ | |
| U0123 | ○ | ○ | ○ | ||
| U0129 | ○ | ○ | ○ | ||
| U0142 | ○ | ○ | ○ | ||
| U0155 | ○ | ○ | ○ | ||
| Sub Bus 1 | Main Body ECU (Multiplex Network Body ECU)*2 | U0199 | - | - | - |
| U0200 | - | - | - | ||
| U0208 | - | - | - | ||
| U0230 | - | - | - | ||
| U1002 | - | - | - | ||
| Multiplex Network Door ECU | U0101 | - | - | - | |
| U0122 | - | - | - | ||
| U0142 | - | - | - | ||
| U0155 | - | - | - | ||
| Sub Bus 1 | Outer Mirror Control ECU Assembly (for Driver Side) | U0142 | - | - | - |
| Outer Mirror Control ECU Assembly (for Front Passenger Side) | U0142 | - | - | - | |
| Position Control ECU and Switch Assembly | - | - | - | - | |
○: DTC is output.
-: DTC is not output.
*1: DTC U0073 may be stored when communication is lost.
*2: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
X: DTC is likely to be output.
▲: DTC is unlikely to be output.
-: DTC is not output.
*1: DTC U0073 may be stored when communication is lost.
*2: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
○: DTC is output.
-: DTC is not output.
*1: DTC U0073 may be stored when communication is lost.
*2: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
X: DTC is likely to be output.
▲: DTC is unlikely to be output.
-: DTC is not output.
*1: DTC U0073 may be stored when communication is lost.
*2: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
○: DTC is output.
-: DTC is not output.
*1: DTC U0073 may be stored when communication is lost.
*2: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
| - | Trouble Mode (CAN Bus Lines Short Circuit or Short to GND) | ||||
|---|---|---|---|---|---|
| Sub Bus 2 | |||||
| Output ECU | Output DTC | CANH to CANL | CANH to Ground Short | CANL to Ground Short | |
| V Bus | Airbag Sensor Assembly | - | - | - | - |
| Air Conditioning Amplifier Assembly | U0100 | - | - | - | |
| U0131 | - | - | - | ||
| U0142 | - | - | - | ||
| U0155 | - | - | - | ||
| Headlight Leveling ECU Assembly | U0100 | - | - | - | |
| U0129 | - | - | - | ||
| U0142 | - | - | - | ||
| Navigation Receiver Assembly*1 | U0100 | - | - | - | |
| U0140 | - | - | - | ||
| U0155 | - | - | - | ||
| Radio and Display Receiver Assembly*1 | U0100 | - | - | - | |
| U0140 | - | - | - | ||
| U0155 | - | - | - | ||
| Main Body ECU (Multiplex Network Body ECU)*2 | U0100 | - | - | - | |
| U0101 | - | - | - | ||
| U0120 | - | - | - | ||
| U0151 | - | - | - | ||
| U0155 | - | - | - | ||
| U023A | ○ | ○ | ○ | ||
| U0327 | - | - | - | ||
| U1126 | ○ | ○ | ○ | ||
| Clearance Warning ECU Assembly | U0101 | - | - | - | |
| U0155 | - | - | - | ||
| Network Gateway ECU*2 | - | - | - | - | |
| ECM (for 1AR-FE) | - | - | - | - | |
| ECM (for 2GR-FE) | - | - | - | - | |
| ECM
(Radar cruise function) |
U0100 | - | - | - | |
| U0122 | - | - | - | ||
| U0123 | - | - | - | ||
| U0126 | - | - | - | ||
| U1104 | ○ | ○ | ○ | ||
| Power Steering ECU Assembly | U0100 | - | - | - | |
| U0129 | - | - | - | ||
| 4WD ECU Assembly*1 | U0100 | - | - | - | |
| U0126 | - | - | - | ||
| U0129 | - | - | - | ||
| V Bus | Certification ECU (Smart Key ECU Assembly)
(Entry function) |
U0100 | - | - | - |
| U0142 | - | - | - | ||
| U0155 | - | - | - | ||
| Certification ECU (Smart Key ECU Assembly)
(Power source switching function) |
U0100 | - | - | - | |
| U0140 | - | - | - | ||
| U0155 | - | - | - | ||
| Certification ECU (Smart Key ECU Assembly)
(Start function) |
U0100 | - | - | - | |
| Combination Meter Assembly | U0100 | - | - | - | |
| U0129 | - | - | - | ||
| U0131 | - | - | - | ||
| U0142 | - | - | - | ||
| U0151 | - | - | - | ||
| U0163 | - | - | - | ||
| U0182 | - | - | - | ||
| U023A | ○ | ○ | ○ | ||
| U1104 | ○ | ○ | ○ | ||
| Steering Sensor | - | - | - | - | |
| Skid Control ECU (Brake Actuator Assembly) | U0073 | - | - | - | |
| U0100 | - | - | - | ||
| U0124 | - | - | - | ||
| U0126 | - | - | - | ||
| Sub Bus 2 | Blind Spot Monitor Sensor LH | U0100 | - | - | - |
| U0126 | - | - | - | ||
| U0129 | - | - | - | ||
| U0142 | - | - | - | ||
| Television Camera Assembly | U0100 | ○ | ○ | ○ | |
| U0126 | ○ | ○ | ○ | ||
| U0129 | ○ | ○ | ○ | ||
| U0131 | ○ | ○ | ○ | ||
| U0140 | ○ | ○ | ○ | ||
| U0163 | ○ | ○ | ○ | ||
| U1110 | ○ | ○ | ○ | ||
| Network Gateway ECU*2 | U0104 | ○ | ○ | ○ | |
| U0233 | ○ | ○ | ○ | ||
| U023A | ○ | ○ | ○ | ||
| U0265 | ○ | ○ | ○ | ||
| U1002 | ○ | ○ | ○ | ||
| Driving Support ECU Assembly
(Pre-crash Safety System) |
U0125 | ○ | ○ | ○ | |
| U0126 | ○ | ○ | ○ | ||
| U0129 | ○ | ○ | ○ | ||
| U0142 | ○ | ○ | ○ | ||
| Lane Departure Warning Camera*1 | U0101 | ○ | ○ | ○ | |
| U0123 | ○ | ○ | ○ | ||
| U0129 | ○ | ○ | ○ | ||
| U0142 | ○ | ○ | ○ | ||
| U0155 | ○ | ○ | ○ | ||
| Sub Bus 1 | Main Body ECU (Multiplex Network Body ECU)*2 | U0199 | - | - | - |
| U0200 | - | - | - | ||
| U0208 | - | - | - | ||
| U0230 | - | - | - | ||
| U1002 | - | - | - | ||
| Multiplex Network Door ECU | U0101 | - | - | - | |
| U0122 | - | - | - | ||
| U0142 | - | - | - | ||
| U0155 | - | - | - | ||
| Outer Mirror Control ECU Assembly (for Front Passenger Side) | U0142 | - | - | - | |
| Outer Mirror Control ECU Assembly (for Driver Side) | U0142 | - | - | - | |
| Position Control ECU and Switch Assembly | - | - | - | - | |
○: DTC is output.
-: DTC is not output.
*1: DTC U0073 may be stored when communication is lost.
*2: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
CAN BUS WAVEFORMS
This waveform is measured between terminals CANH and GND, and terminals CANL and GND of the DLC3. (Use this as a reference for diagnosis of CAN communication lines.)
When malfunctions in multiple ECUs are suspected based on the CAN bus check and DTCs checked using the GTS, check the resistance of the CAN bus using an ohmmeter first. If no problems are found, check the following waveforms.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
If a waveform is not similar to one of the following 3 patterns (Group 1), then an open in a CAN main bus line, an open in a CAN branch line, or a short between a CAN line (CANH or CANL) and ground is suspected (Group 2).
Wiggle the connector and wire harness to check if the waveform changes.
CAN bus waveforms (Group 1)
Normal waveform
Open in both of the lines (CANH and CANL) of a CAN branch
Waveforms (waveforms shown using dotted lines) are not present from an ECU or sensor connected to a CAN branch with an open circuit in both lines. (Waveforms from other ECUs or sensors are normal.)
Because this waveform is similar to a normal waveform, instead of using the waveform, the malfunctioning part can be narrowed down by performing a CAN bus check.
Short between the CAN bus lines (CANH and CANL)
Waveforms disappear.
If the malfunction is in an ECU, disconnecting the ECU will change the waveform. If the waveform does not change, a malfunction in the wire harness is suspected.
CAN bus waveforms (reference) (Group 2)
The following CAN bus waveforms can be used only as reference. The actual measured waveform may differ significantly depending on the location of the open or short circuit.
Open in a CAN branch line (CANH)
An abnormal waveform is output from an ECU with an open in one of its CAN branch lines. Because this abnormal output interferes with the signals from other ECUs, the output of other ECUs will also appear abnormal.
Narrow down the malfunctioning part by checking DTCs or performing a CAN bus check, or by checking waveform changes when ECUs or sensors are disconnected. The waveform will change to one for an open in both sides of a CAN branch when the ECU or sensor with an open CAN branch line is disconnected.
Open in a CAN branch line (CANL)
An abnormal waveform is output from an ECU with an open in one of its CAN branch lines. Because this abnormal output interferes with the signals from other ECUs, the output of other ECUs will also appear abnormal.
Narrow down the malfunctioning part by checking DTCs or performing a CAN bus check, or by checking waveform changes when ECUs or sensors are disconnected. The waveform will change to one for an open in both sides of a CAN branch when the ECU or sensor with an open CAN branch line is disconnected.
Open in a CAN main bus line (CANH)
Waveforms of ECUs or sensors that are closer to the DLC3 than the open part are almost normal.
Waveforms of ECUs or sensors that are on the opposite side of the DLC3 from the open part are abnormal.
An open in a CAN main bus line can be confirmed by measuring the resistance between the CANH and CANL terminals of any CAN branch.
Short between a CAN bus line (CANH) and ground
Narrow down the shorted part by checking for waveform changes when disconnecting connectors from the CAN junction connectors or when disconnecting ECUs or sensors.
A short to ground in the CANH line can be confirmed by measuring the resistance between CANH and ground using an ohmmeter.
Short between a CAN bus line (CANL) and ground
Narrow down the shorted part by checking for waveform changes when disconnecting connectors from the CAN junction connectors or when disconnecting ECUs or sensors.
A short to ground in the CANL line can be confirmed by measuring the resistance between CANL and ground using an ohmmeter.
DATA SENDING/RECEIVING TABLE
Data sending/receiving table
If Data List items related to sent/received data are not displayed properly, the part for which communication is interrupted can be determined using the table below.
| Data content | Data Detected and Sent by | Data Received by
(Can be Checked in Data List) |
Data Received by
(Cannot be Checked in Data List) |
Relevant Data List Item
[Selected System] |
|---|---|---|---|---|
| Accelerator position | ECM | Skid control ECU (brake actuator assembly) | ·
Power steering ECU assembly ·
4WD ECU assembly |
·
Accelerator Position [Engine] ·
Accelerator Opening Angle % [ABS/VSC/TRC] |
| Engine speed | ECM | ·
Skid control ECU (brake actuator assembly) ·
Power steering ECU assembly ·
Combination meter assembly ·
Certification ECU (smart key ECU assembly) |
·
4WD ECU assembly ·
Main body ECU (multiplex network body ECU) ·
Air conditioning amplifier assembly ·
Airbag sensor assembly ·
Navigation receiver assembly ·
Radio and display receiver assembly |
·
Engine Speed [Engine] ·
Engine Revolutions [ABS/VSC/TRC] ·
Engine Revolution [EMPS] ·
Engine Rpm [Combination Meter] ·
Engine Condition [Power Source Control] ·
Engine Speed [Starting Control] |
| Engine coolant temperature | ECM | ·
Combination meter assembly ·
4WD ECU assembly ·
Air conditioning amplifier assembly |
·
Navigation receiver assembly ·
Radio and display receiver assembly |
·
Coolant Temp [Engine] ·
Coolant Temperature [Combination Meter] ·
Engine Coolant Temperature [Four Wheel Drive] ·
Engine Coolant Temp [Air Conditioner] |
| Vehicle speed | Skid control ECU (brake actuator assembly) | ·
ECM ·
Power steering ECU assembly ·
Combination meter assembly*3 ·
Navigation receiver assembly ·
Radio and display receiver assembly ·
Blind spot monitor sensor LH ·
Television camera assembly |
·
Airbag sensor assembly ·
Driving support ECU assembly |
·
Vehicle Speed [Engine] ·
Vehicle Speed [ABS/VSC/TRC] ·
Meter Vehicle Velocity [EMPS] ·
Vehicle Speed Meter [Combination Meter] ·
Vehicle Speed [Navigation System] ·
Vehicle Speed [Blind Spot Monitor Master] ·
CCS Vehicle Spd [Radar Cruise] ·
Wheel Speed Sensor (4wheel) [IPA/Parking Assist Monitor] |
| Combination meter assembly*3 | ·
Certification ECU (smart key ECU assembly) ·
Clearance warning ECU assembly ·
Position control ECU and switch assembly |
·
Main body ECU (multiplex network body ECU) ·
Air conditioning amplifier assembly ·
Multiplex network door ECU ·
Option connector (bus buffer ECU) |
·
Vehicle Speed Meter [Combination Meter] ·
Vehicle Speed Signal [Power Source Control] ·
Vehicle Speed Info [Clearance Sonar] ·
Vehicle Speed [Driver Seat] |
|
| Wheel speed | Skid control ECU (brake actuator assembly) | ·
4WD ECU assembly ·
Headlight leveling ECU assembly |
·
ECM ·
Power steering ECU assembly ·
Airbag sensor assembly ·
Blind spot monitor sensor LH ·
Lane departure warning camera ·
Driving support ECU assembly |
·
FR Wheel Speed [ABS/VSC/TRC] ·
FL Wheel Speed [ABS/VSC/TRC] ·
RR Wheel Speed [ABS/VSC/TRC] ·
RL Wheel Speed [ABS/VSC/TRC] ·
FR Wheel Speed [Four Wheel Drive] ·
FL Wheel Speed [Four Wheel Drive] ·
RR Wheel Speed [Four Wheel Drive] ·
RL Wheel Speed [Four Wheel Drive] ·
Front Right Wheel Speed Value [HL AutoLeveling] ·
Front Left Wheel Speed Value [HL AutoLeveling] |
| Shift position | ECM | ·
Navigation receiver assembly ·
Radio and display receiver assembly ·
Certification ECU (smart key ECU assembly) ·
Clearance warning ECU assembly ·
Blind spot monitor sensor LH ·
Position control ECU and switch assembly |
·
Combination meter assembly*2 ·
Main body ECU (multiplex network body ECU) ·
Airbag sensor assembly ·
Driving support ECU assembly ·
Lane departure warning camera ·
Television camera assembly ·
Multiplex network door ECU ·
Option connector (bus buffer ECU) |
·
Neutral Position SW Signal [Engine] ·
Reverse Signal [Navigation System] ·
Shift P Signal [Power Source Control] ·
Parking Signal [Clearance Sonar] ·
Reverse Signal [Clearance Sonar] ·
Reverse (Only for AT/CVT) [Blind Spot Monitor Master] ·
P Switch [Driver Seat] |
| Ambient temperature | Air conditioning amplifier assembly | ·
ECM*5 ·
Combination meter assembly ·
4WD ECU assembly |
·
Navigation receiver assembly ·
Radio and display receiver assembly ·
Driving support ECU assembly ·
Option connector (bus buffer ECU) |
·
Ambient Temp for A/C [Engine] ·
Ambient Temp Sensor [Air Conditioner] ·
Ambient Temperature [Combination Meter] ·
Ambient Temperature [Four Wheel Drive] |
| Driver door courtesy switch | Main body ECU (multiplex network body ECU) | - | ·
Combination meter assembly*2 ·
Certification ECU (smart key ECU assembly) ·
Navigation receiver assembly ·
Radio and display receiver assembly ·
Option connector (bus buffer ECU) |
·
FL Door Courtesy SW [Main Body] ·
FR Door Courtesy SW [Main Body] |
| Steering angle sensor | Steering sensor | ·
Skid control ECU (brake actuator assembly) ·
Power steering ECU assembly ·
4WD ECU assembly ·
Blind spot monitor sensor LH |
·
Navigation receiver assembly ·
Radio and display receiver assembly ·
Airbag sensor assembly ·
Driving support ECU assembly ·
Television camera assembly |
·
Steering Angle Sensor [ABS/VSC/TRC] ·
Steering Angle Velocity [EMPS] ·
Steering Angle Value [Four Wheel Drive] ·
Steering Angle [Blind Spot Monitor Master] |
| Yaw rate sensor | Airbag sensor assembly | ·
Skid control ECU (brake actuator assembly) ·
4WD ECU assembly |
·
Driving support ECU assembly ·
Lane departure warning camera |
·
Yaw Rate Sensor [ABS/VSC/TRC] ·
Yaw Rate Value [Four Wheel Drive] |
| Deceleration Sensor | Airbag sensor assembly | ·
Skid control ECU (brake actuator assembly) ·
4WD ECU assembly |
ECM | ·
Deceleration Sensor [ABS/VSC/TRC] ·
Deceleration Sensor2 [ABS/VSC/TRC] ·
Lateral G [Four Wheel Drive] ·
Forward and Rearward G [Four Wheel Drive] |
| Ignition switch condition | Main body ECU (multiplex network body ECU) | ·
Position control ECU and switch assembly ·
Multiplex network door ECU |
·
Certification ECU (smart key ECU assembly) ·
Outer mirror control ECU assembly (for driver side) ·
Outer mirror control ECU assembly (for front passenger side) ·
Television camera assembly ·
Option connector (bus buffer ECU) |
·
IG SW [Main Body] ·
Ignition Switch [Driver Seat] ·
IG SW [Back Door] |
| Driver side buckle switch signal | Airbag sensor assembly | - | Main body ECU (multiplex network body ECU) | ·
Left side Buckle SW [SRS Airbag]*6 ·
Right side Buckle SW [SRS Airbag]*7 |
| Main body ECU (multiplex network body ECU)*4 | - | Combination meter assembly*2 | - | |
| Passenger side buckle switch signal | Airbag sensor assembly | Combination meter assembly | - | ·
P-Seatbelt Buckle SW [Combination Meter] ·
Right side Buckle SW [SRS Airbag]*6 |
| Headlight switch | Main body ECU (multiplex network body ECU) | ·
Combination meter assembly ·
Headlight leveling ECU assembly ·
Lane departure warning camera |
·
ECM ·
Air conditioning amplifier assembly ·
Blind spot monitor sensor LH ·
Driving support ECU assembly ·
Combination meter assembly |
·
Dimmer SW [Main Body] ·
Head Light SW (Head) [Main Body] ·
Head Light SW (Tail) [Main Body] ·
Tail Relay SW [Combination Meter] ·
Headlight Low Beam State [HL AutoLeveling] ·
Headlight High Beam State [HL AutoLeveling] ·
Head Light (High Beam) [Lane Departure Alert] |
| Side turn signal | Combination meter assembly*2 | ·
Blind spot monitor sensor LH ·
Lane departure warning camera |
Driving support ECU assembly | ·
Turn Switch State [Blind spot monitor Master] ·
Turn Signal Switch (Right) [Lane Departure Alert] ·
Turn Signal Switch (Left) [Lane Departure Alert] |
| ECM power source voltage*1 | ECM | - | - | Battery Voltage [Engine] |
| Combination meter assembly power source voltage*1 | Combination meter assembly | - | - | +B Voltage Value [Combination Meter] |
| Skid control ECU (brake actuator assembly) power source voltage*1 | Skid control ECU (brake actuator assembly) | - | - | IG1 Voltage Value [ABS/VSC/TRC] |
| Power steering ECU assembly power source voltage*1 | Power steering ECU assembly | - | - | IG Power Supply [EMPS] |
| Navigation receiver assembly power source voltage*1 | Navigation receiver assembly | - | - | Battery Voltage [Navigation System] |
| Radio and display receiver assembly power source voltage*1 | Radio and display receiver assembly | - | - | Battery Voltage [Navigation System] |
| Headlight leveling ECU assembly power source voltage*1 | Headlight leveling ECU assembly | - | - | +B [HL AutoLeveling] |
| Solar sensor*1 | Air conditioning amplifier assembly | - | - | Solar Sensor (D side) [Air Conditioner] |
| Driver door touch sensor*1 | Certification ECU (smart key ECU assembly) | - | - | D-Door Touch Sensor [Entry&Start] |
| Clearance sonar main switch condition*1 | Clearance warning ECU assembly | - | - | Main Switch [Clearance Sonar] |
| Transfer control solenoid current*1 | 4WD ECU assembly | - | - | SLC Solenoid Current [Four Wheel Drive] |
| Blind spot monitor sensor LH power source voltage*1 | Blind spot monitor sensor LH | - | - | Power Supply Voltage [Blind Spot Monitor Master] |
| Outer mirror control ECU assembly (for driver side) power source voltage*1 | Outer mirror control ECU assembly (for driver side) | - | - | ·
+B Voltage Input Value [Mirror L]*6 ·
+B Voltage Input Value [Mirror R]*7 |
| Outer mirror control ECU assembly (for front passenger side) power source voltage*1 | Outer mirror control ECU assembly (for front passenger side) | - | - | ·
+B Voltage Input Value [Mirror R]*6 ·
+B Voltage Input Value [Mirror L]*7 |
| Position control ECU and switch assembly power source voltage*1 | Position control ECU and switch assembly | - | - | Power Voltage [Driver Seat] |
| Wiper operation status*1 | Driving support ECU assembly | - | - | Wiper Information [Pre-Crash 2] |
*1: Whether the ECU that sends data is functioning or not can be judged by using the GTS to check items such as switches or sensors that send signals to the ECU via direct lines.
*2: Although the received contents cannot be checked in the Data List, whether or not the data is received normally can be checked by observing the combination meter assembly.
*3: The combination meter assembly receives a vehicle speed signal from the skid control ECU (brake actuator assembly) and sends the signal to other ECUs.
*4: The main body ECU (multiplex network body ECU) receives a driver seat buckle switch signal from the airbag ECU assembly and sends the signal to other ECUs.
*5: for 1AR-FE
*6: for LHD
*7: for RHD
Details of relevant Data List items (Selected system: Engine) (for 1AR-FE)
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Normal Condition: If no conditions are specifically stated for "idling", the shift lever should be in N or P, the A/C switch should be off and all accessory switches should be off.
Warm up the engine.
Turn the A/C switch off.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
According to the display on the GTS, read the "Data List".
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Vehicle Speed | Vehicle speed | Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) | Actual vehicle speed | ·
This is the current vehicle speed. ·
The vehicle speed is detected using the wheel speed sensors. -
Vehicle speed data is delayed when it is displayed. Therefore, even if the vehicle speed listed in the freeze frame data is 0 km/h (0 mph), this does not always mean that the malfunction occurred when the vehicle was stopped. |
| Engine Speed | Engine speed | Min.: 0 rpm, Max.: 16383 rpm | 610 to 710 rpm: Idling | When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed. |
| Coolant Temp | Coolant temperature | Min.: -40°C (-40°F), Max.: 140°C (284°F) | 75 to 100°C (167 to 212°F): After warming up | This is the engine coolant temperature.
|
| Battery Voltage | Battery voltage | Min.: 0 V, Max.: 65.535 V | 11 to 14 V: Idling | If 11 V or less, characteristics of some electrical components may change. |
| Accelerator Position | Accelerator pedal position | Min.: 0%, Max.: 399.9% | Actual accelerator pedal position | This is the accelerator pedal position defined using the learned fully released position (sensor output) of No. 1 accelerator pedal position sensor as 0% and the fully depressed position as 100%. |
| Neutral Position SW Signal | Neutral Position switch signal status | ON or OFF | ON: Shift lever in P or N | - |
| Ambient Temp for A/C | Ambient temperature for A/C | Min.: -40°C (-40°F), Max.: 215°C (419°F) | - | - |
Details of relevant Data List items (Selected system: Engine) (for 2GR-FE)
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Normal Condition: If no conditions are specifically stated for "idling", the shift lever should be in N or P, the A/C switch should be off and all accessory switches should be off.
Warm up the engine.
Turn the A/C switch off.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List.
According to the display on the GTS, read the "Data List".
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Vehicle Speed | Vehicle speed | Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) | Actual vehicle speed | ·
This is the current vehicle speed. ·
The vehicle speed is detected using the wheel speed sensors. -
Vehicle speed data is delayed when it is displayed. Therefore, even if the vehicle speed listed in the freeze frame data is 0 km/h (0 mph), this does not always mean that the malfunction occurred when the vehicle was stopped. |
| Engine Speed | Engine speed | Min.: 0 rpm, Max.: 16383 rpm | 600 to 700 rpm: Idling | When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed. |
| Coolant Temp | Coolant temperature | Min.: -40°C (-40°F), Max.: 140°C (284°F) | 75 to 100°C (167 to 212°F): After warming up | This is the engine coolant temperature.
|
| Battery Voltage | Battery voltage | Min.: 0 V, Max.: 65.535 V | 11 to 14 V: Idling | If 11 V or less, characteristics of some electrical components may change. |
| Accelerator Position | Accelerator pedal position | Min.: 0%, Max.: 399.9% | Actual accelerator pedal position | This is the accelerator pedal position defined using the learned fully released position (sensor output) of No. 1 accelerator pedal position sensor as 0% and the fully depressed position as 100%. |
| Neutral Position SW Signal | Neutral Position switch signal status | ON or OFF | ON: Shift lever in P or N | - |
| Ambient Temp for A/C | Ambient temperature for A/C | Min.: -40°C (-40°F), Max.: 215°C (419°F) | - | - |
Details of relevant Data List items (Selected system: ABS/VSC/TRC)
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
According to the display on the GTS, read the "Data List".
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Deceleration Sensor | Acceleration sensor reading | Min.: -18.525 m/s2, Max.: 18.387 m/s2 | - | During deceleration/acceleration: Changes continuously |
| Deceleration Sensor2 | Acceleration sensor 2 reading | Min.: -18.525 m/s2, Max.: 18.387 m/s2 | - | During deceleration/acceleration: Changes continuously |
| Yaw Rate Sensor | Yaw rate sensor | Min.: -128°/s, Max.: 127°/s | Vehicle stopped: 0°/s
Turning right: -128 to 0°/s Turning left: 0 to 127°/s |
- |
| Steering Angle Sensor | Steering angle sensor | Min.: -3276.8°, Max.: 3276.7° | Turning left: Increases
Turning right: Decreases |
- |
| FR Wheel Speed | Front wheel speed sensor RH reading | Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| FL Wheel Speed | Front wheel speed sensor LH reading | Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| RR Wheel Speed | Rear wheel speed sensor RH reading | Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| RL Wheel Speed | Rear wheel speed sensor LH reading | Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| Vehicle Speed | Maximum wheel speed sensor reading | Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| Engine Revolutions | Engine speed | Min.: 0 rpm, Max.: 65535 rpm | Engine stopped:
0 rpm |
When engine speed is constant:
No large fluctuations |
| Accelerator Opening Angle % | Percentage of accelerator pedal opening angle | Min.: 0.0%, Max.: 128.0% | Accelerator pedal released: 0.0% | During accelerator pedal operation: Changes in proportion with the pedal movement |
| IG1 Voltage Value | IG1 voltage value | Min.: 0.00 V, Max.: 20.00 V | Ignition switch ON: 11.00 to 14.00 V | Changes in proportion to battery voltage |
Details of relevant Data List items (Selected system: EMPS)
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / EMPS / Data List.
According to the display on the GTS, read the "Data List".
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Meter Vehicle Velocity | Vehicle speed from speedometer | Min.: 0.0 km/h (0.0 MPH)
Max.: 300.0 km/h (186.4 MPH) |
·
0 km/h (0 MPH): Engine running and vehicle stopped ·
No significant fluctuation: Engine running and vehicle driven at a constant speed |
- |
| Engine Revolution | Engine speed | Min.: 0 rpm
Max.: 12800 rpm |
No significant fluctuation | Engine running at a constant speed |
| Steering Angle Velocity | Steering angle speed | Min.: -32768 deg/s
Max.: 32767 deg/s |
Value changes in proportion to steering speed
- The value increases when turning left and decreases when turning right |
Engine running and steering wheel being turned |
| IG Power Supply | IG power source voltage | Min.: 0.0000 V
Max.: 20.1531 V |
9 to 16 V | Ignition switch ON |
Details of relevant Data List items (Selected system: Combination Meter)
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Combination Meter / Data List.
According to the display on the GTS, read the "Data List".
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Tail Relay SW | Tail relay | OFF or ON | OFF: Tail relay off
ON: Tail relay on |
- |
| P-Seatbelt Buckle SW | Front passenger seat belt buckle switch | OFF or ON | OFF: Front passenger seat belt fastened (seat belt warning light off)
ON: Front passenger seat belt unfastened (seat belt warning light on) |
- |
| Vehicle Speed Meter | Vehicle speed | Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) | Almost the same as actual vehicle speed | - |
| Engine Rpm | Engine speed | Min.: 0 rpm, Max.: 12750 rpm | Almost the same as actual tachometer | - |
| Coolant Temperature | Engine coolant temperature | Min.: 0°C (32°F), Max.: 127.5°C (261.5°F) | 75 to 100°C (167 to 212°F): After warming up engine | - |
| +B Voltage Value | Battery voltage | Min.: 0 V, Max.: 25.5 V | 11 to 14 V | - |
| Ambient Temperature | Outside temperature | Min.: -40°C (-40°F), Max.: 87.5°C (189.5°F) | Almost the same as actual outside temperature | The temperature displayed on the multi-information display is -40 to 50°C (-40 to 122°F) |
Details of relevant Data List items (Selected system: Power Source Control)
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Power Source Control / Data List.
According to the display on the GTS, read the "Data List".
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Shift P Signal | Shift position P | OFF or ON | OFF: Shift lever not in P
ON: Shift lever in P |
Use this item to determine whether the shift lever position switch (P) is malfunctioning. |
| Engine Condition | Engine state | Stop or Run | Stop: Engine stopped
Run: Engine running |
- |
| Vehicle Speed Signal | Vehicle being driven or stopped | Stop or Run | Stop: Vehicle stopped
Run: Vehicle being driven at 5 km/h (3 mph) or more |
- |
Details of relevant Data List items (Selected system: Starting Control)
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Starting Control / Data List.
According to the display on the GTS, read the "Data List".
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Shift Position P or N | Park/Neutral position switch status | OFF or ON | OFF: Shift lever not in P
ON: Shift lever in P |
When malfunctioning, the engine will not crank. |
| Engine Speed | Engine speed | 0 to 16383 rpm | Fluctuates in accordance with engine speed | - |
Details of relevant Data List items (Selected system: Air Conditioner)
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Air Conditioner / Data List.
According to the display on the GTS, read the "Data List".
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Ambient Temp Sensor | Thermistor assembly | Min.: -23.30°C (-9.94°F)
Max.: 65.95°C (150.71°F) |
Actual ambient temperature displayed | - |
| Solar Sensor (D Side) | Driver side automatic light control sensor | Min.: 0
Max.: 255 |
Driver side automatic light control sensor value increases as brightness increases | * |
| Engine Coolant Temp | Engine coolant temperature sensor | Min.: 1.30°C (34.34°F)
Max.: 90.55°C (194.99°F) |
Actual engine coolant temperature displayed | - |
*: for Automatic Air Conditioning System
Details of relevant Data List items (Selected system: Back Door)
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Back Door / Data List.
According to the display on the GTS, read the "Data List".
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| IG SW | Ignition switch signal | ON or OFF | ON: Ignition switch ON
OFF: Ignition switch off |
"OFF" is also displayed for this item when the ignition switch is ACC. |
Details of relevant Data List items (Selected system: Navigation System)
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Navigation System / Data List.
According to the display on the GTS, read the "Data List".
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Battery Voltage | Battery voltage | Min.: 0 V, Max.: 24 V | 11 to 14 V | - |
| Reverse Signal | Reverse signal | ON or OFF | ON: Shift lever in R
OFF: Shift lever in any position other than R |
- |
| Vehicle Speed | Maximum wheel speed sensor reading | Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
Details of relevant Data List items (Selected system: Blind Spot Monitor Master)
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Blind Spot Monitor Master / Data List.
According to the display on the GTS, read the "Data List".
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Turn Switch State | State of the turn signal switch | Left ON, Right ON or OFF | Left ON: Left side of turn signal switch on
Right ON: Right side of turn signal switch on OFF: Turn signal switch off |
- |
| Reverse (Only for AT/CVT) | State of the shift position R signal | OFF or ON | OFF: Shift lever in any position except R
ON: Shift lever in R |
- |
| Vehicle Speed | Vehicle speed signal | Min.: -327.68 km/h (-204 mph), Max.: 327.67 km/h (204 mph) | Vehicle stopped: 0 km/h (0 mph) | - |
| Steering Angle | Steering angle sensor | Min.: -3072 deg, Max.: 3070.5 deg | Left turn: Increases
Right turn: Decreases |
- |
| Power Supply Voltage | Power supply voltage | Min.: 0 V, Max.: 49.951 V | Engine switch on (IG): 11 to 14 V | - |
Details of relevant Data List items (Selected system: Radar Cruise)
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Radar Cruise / Data List.
According to the display on the GTS, read the "Data List".
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| CCS Vehicle Spd | Vehicle speed | min.: 0 km/h (0 mph), max.: 255 km/h (158 mph) | Actual vehicle speed | - |
Details of relevant Data List items (Selected system: Clearance Sonar)
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Clearance Sonar / Data List.
According to the display on the GTS, read the "Data List".
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Main Switch | Back sonar or clearance sonar switch assembly | OFF or ON | OFF: Back sonar or clearance sonar switch assembly off
ON: Back sonar or clearance sonar switch assembly on |
- |
| Parking Signal | Parking signal | OFF or ON | OFF: Shift lever in any position except P
ON: Shift lever in P |
- |
| Reverse Signal | Reverse signal | OFF or ON | OFF: Shift lever in any position except R
ON: Shift lever in R |
- |
| Vehicle Speed Info | Vehicle speed signal | Snr Stop or Snr Work | Snr Stop: Vehicle speed 15 km/h (9 mph) or more (when accelerating) or 10 km/h (6 mph) or more (when decelerating)
Snr Work: Vehicle speed less than 15 km/h (9 mph) (when accelerating) or less than 10 km/h (6 mph) (when decelerating) |
- |
Details of relevant Data List items (Selected system: Four Wheel Drive)
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / Four Wheel Drive / Data List.
According to the display on the GTS, read the "Data List".
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Lateral G | Lateral G | Min.: -25.10 m/s2
max.: 24.90 m/s2 |
- | Changes in proportion with acceleration during turning. |
| Forward and Rearward G | Forward and Rearward G | Min.: -25.10 m/s2
Max.: 24.90 m/s2 |
Approximately 0 +/-0.13 m/s2 while stationary | Changes in proportion with acceleration/deceleration. |
| Yaw Rate Value | Yaw rate value | Min.: -128°/s
Max.: 127°/s |
- | Changes in proportion with yaw during turning. |
| Steering Angle Value | Steering angle value | Min.: -3276.8°
Max.: 3276.7° |
Left turn: Increases
Right turn: Decreases |
Changes in proportion with the amount of steering wheel rotation during steering operation. |
| FR Wheel Speed | Front wheel speed sensor RH reading | Min.: 0 km/h (0 mph)
Max.: 326 km/h (202 mph) |
Vehicle stopped: 0 km/h (0 mph) | No large fluctuations when driving at a constant speed. |
| FL Wheel Speed | Front wheel speed sensor LH reading | Min.: 0 km/h (0 mph)
Max.: 326 km/h (202 mph) |
Vehicle stopped: 0 km/h (0 mph) | No large fluctuations when driving at a constant speed. |
| RR Wheel Speed | Rear wheel speed sensor RH reading | Min.: 0 km/h (0 mph)
Max.: 326 km/h (202 mph) |
Vehicle stopped: 0 km/h (0 mph) | No large fluctuations when driving at a constant speed. |
| RL Wheel Speed | Rear wheel speed sensor LH reading | Min.: 0 km/h (0 mph)
Max.: 326 km/h (202 mph) |
Vehicle stopped: 0 km/h (0 mph) | No large fluctuations when driving at a constant speed. |
| Engine Coolant Temperature | Engine coolant temperature | Min.: 0°C (32°F)
Max.: 127.5°C (261.5°F) |
Actual engine coolant temperature is displayed | - |
| Ambient Temperature | Vehicle ambient temperature | Min.: -128°C (-198.4°F)
Max.: 127°C (260.6°F) |
Actual ambient temperature is displayed | - |
| SLC Solenoid Current | SLC solenoid (4WD linear solenoid) current | Min.: 0 A
Max.: 3 A |
0 to 3 A | - |
Details of relevant Data List items (Selected system: Driver Seat)
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Driver Seat / Data List.
According to the display on the GTS, read the "Data List".
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Ignition Switch | Communication state of engine switch signal | ON or OFF | ON: Engine switch on (IG)
OFF: Engine switch off or on (ACC) |
- |
| P Switch | Park state signal | ON or OFF | ON: Shift lever in P
OFF: Shift lever in a position other than P |
- |
| Vehicle Speed | Vehicle speed data | Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) | Actual vehicle speed | - |
| Power Voltage | Power supply for front power seat switch (driver seat) | Min: 0.95 V, Max: 20.84 V | Within range from 11 to 14 V | - |
Details of relevant Data List items (Selected system: IPA/Parking Assist Monitor)
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / IPA/Parking Assist Monitor / Data List.
According to the display on the GTS, read the "Data List".
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Wheel Speed Sensor (4wheel) | Vehicle speed signal from speed sensor | OK or NG | OK: Speed signal normal
NG: Speed signal abnormal |
- |
Details of relevant Data List items (Selected system: HL AutoLeveling)
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / HL AutoLeveling / Data List.
According to the display on the GTS, read the "Data List".
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Headlight Low Beam State | Low beam headlight state | ON or OFF | ON: Low beam headlights on
OFF: Low beam headlights off |
- |
| Headlight High Beam State | High beam headlight state | ON or OFF | ON: High beam headlights on
OFF: High beam headlights off |
- |
| +B | IG power supply voltage value | 0.00 to 19.75 V | 11 to 14 V | - |
| Front Right Wheel Speed Value | Front right wheel speed | 0.00 to 260.00 km/h (162.00 mph) | Condition can be displayed | - |
| Front Left Wheel Speed Value | Front left wheel speed | 0.00 to 260.00 km/h (162.00 mph) | Condition can be displayed | - |
Details of relevant Data List items (Selected system: Main Body)
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Data List.
According to the display on the GTS, read the "Data List".
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| IG SW | Ignition switch ON signal | ON or OFF | ON: Ignition switch ON
OFF: Ignition switch off |
"OFF" is also displayed for this item when the ignition switch is ACC. |
| FR Door Courtesy SW | Front door courtesy light switch assembly RH signal | ON or OFF | ON: Front door RH open
OFF: Front door RH closed |
- |
| FL Door Courtesy SW | Front door courtesy light switch assembly LH signal | ON or OFF | ON: Front door LH open
OFF: Front door LH closed |
- |
| Dimmer SW | Dimmer switch high position signal | ON or OFF | ON: Dimmer switch in high or high flash position
OFF: Dimmer switch in low position |
- |
| Head Light SW (Head) | Light control switch head position signal | ON or OFF | ON: Light control switch in head position
OFF: Light control switch not in head position |
- |
| Head Light SW (Tail) | Light control switch tail position signal | ON or OFF | ON: Light control switch in tail or head position
OFF: Light control switch in neither tail nor head position |
- |
Details of relevant Data List items (Selected system: Lane Departure Alert)
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / Lane Departure Alert / Data List.
According to the display on the GTS, read the "Data List".
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Head Light (High Beam) | Status of the head light (high beam) | OFF or ON | ON: Headlight dimmer switch HI
OFF: Headlight dimmer switch except HI |
- |
| Turn Signal Switch (Right) | Status of turn signal light switch (right) | OFF or ON | ON: Turn signal light switch on (right)
OFF: Turn signal light switch off |
- |
| Turn Signal Switch (Left) | Status of turn signal light switch (left) | OFF or ON | ON: Turn signal light switch on (left)
OFF: Turn signal light switch off |
- |
Details of relevant Data List items (Selected system: Entry&Start)
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
When using the GTS with the ignition switch off to troubleshoot:
Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Entry&Start / Data List.
According to the display on the GTS, read the "Data List".
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| D-Door Touch Sensor | Driver door touch sensor (unlock sensor) | ON or OFF | ON: Driver door touch sensor (unlock sensor) touched
OFF: Driver door touch sensor (unlock sensor) not touched |
·
Displays whether the unlock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily). ·
Use this Data List item to help determine if there is an unlock sensor malfunction when the entry unlock function does not operate. |
Details of relevant Data List items (Selected system: Mirror R)
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Mirror R / Data List.
According to the display on the GTS, read the "Data List".
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| +B Voltage Input Value | Power supply for outer mirror control ECU assembly | MIN: 0 V, MAX: 25.5 V | 11 to 14 V | - |
Details of relevant Data List items (Selected system: Mirror L)
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Mirror L / Data List.
According to the display on the GTS, read the "Data List".
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| +B Voltage Input Value | Power supply for outer mirror control ECU assembly | MIN: 0 V, MAX: 25.5 V | 11 to 14 V | - |
Details of relevant Data List items (Selected system: Pre-Crash 2)
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Pre-Crash 2 / Data List.
According to the display on the GTS, read the "Data List".
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Wiper Information | Wiper operational status | Unoperat, Oil off, Mist, Washer, Unknown, Intermi, Lo or Hi | The respective operational status displayed | - |
Details of relevant Data List items (Selected system: SRS Airbag)
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / SRS Airbag / Data List.
According to the display on the GTS, read the "Data List".
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Left side Buckle SW | Front LH Buckle Switch | Unset: Seat belt is not fastened
Set: Seat belt is fastened NG: Data is not determined |
Unset/Set | for LHD |
| Right side Buckle SW | Front RH Buckle Switch | Unset: Seat belt is not fastened
Set: Seat belt is fastened NG: Data is not determined |
Unset/Set | - |