Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM3160E _57 Power Source / Network _019704 NETWORKING _0095663 CAN COMMUNICATION SYSTEM C

NETWORKING  CAN COMMUNICATION SYSTEM  U0208  Lost Communication with "Seat Control Module A"  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Note
U0208 Lost Communication with "Seat Control Module A" No communication from the position control ECU and switch assembly continues.
·

Position control ECU and switch assembly branch line or connector

·

Power source circuit of position control ECU and switch assembly

·

Position control ECU and switch assembly ground circuit

·

Position control ECU and switch assembly


HINT:

Main body ECU (multiplex network body ECU) stores DTCs when it detects a communication stop or network communication error for ECUs connected to sub bus 1.



HINT:

This diagnosis procedure is for when DTC U0208 is output by the main body ECU (multiplex network body ECU) (GTS display: Main Body).


WIRING DIAGRAM

C294980E01
1.708,1.125 2.208,0.198 2.208,0.198 2.344,0.198 false 4.688,1.125 5.188,0.198 5.188,0.198 5.323,0.198 false 0.031,0.031 1.865,0.271 1.833,0.24 12 false Sub Bus 1 (for LHD): 2.406,0.104 3.646,0.74 1.24,0.635 10 false No. 5 CAN Junction Connector 5.396,0.104 6.635,0.74 1.24,0.635 10 false No. 6 CAN Junction Connector 0.708,2.01 1.479,2.208 0.771,0.198 10 false 120 Ω 6.156,2.01 6.927,2.208 0.771,0.198 10 false 120 Ω 0.302,2.635 1.427,3.125 1.125,0.49 10 false Multiplex Network Door ECU 5.5,2.646 7.146,3.802 1.646,1.156 10 false Main Body ECU (Multiplex Network Body ECU) 3.031,4.156 4.635,4.729 1.604,0.573 10 false Position Control ECU and Switch Assembly 1.125,5.063 5.104,5.26 3.979,0.198 10 false : CAN Main Bus Line (CANH) 4.26,5.063 6.052,5.313 1.792,0.25 10 false : CAN Branch Line (CANH) 1.01,3.656 2.844,3.854 1.833,0.198 10 false Trouble Area 1.125,5.396 5.104,5.594 3.979,0.198 10 false : CAN Main Bus Line (CANL) 4.26,5.396 6.073,5.708 1.813,0.313 10 false : CAN Branch Line (CANL) 1.979,4.115 2.76,4.323 0.781,0.208 10 false IG1 NO. 3 1.927,3.708 3.458,3.906 1.531,0.198 10 false MPX-B NO. 1 1.958,3.302 3.49,3.5 1.531,0.198 10 false P/SEAT F/L 3.385,3.125 4,3.323 0.615,0.198 10 false CANP 3.833,3.125 4.448,3.323 0.615,0.198 10 false CANN 4.177,3.26 4.635,3.458 0.458,0.198 10 false GND 3.104,3.156 3.417,3.354 0.313,0.198 10 false +B 3.094,3.563 3.708,3.76 0.615,0.198 10 false SYSB 3.104,3.948 3.417,4.146 0.313,0.198 10 false IG 2.813,3.167 3.271,3.365 0.458,0.198 10 false e6 3.521,2.927 3.979,3.125 0.458,0.198 10 false e7 3.906,2.927 4.365,3.125 0.458,0.198 10 false e7 4.594,3.25 5.052,3.448 0.458,0.198 10 false e6 2.823,3.552 3.281,3.75 0.458,0.198 10 false e7 2.823,3.938 3.281,4.135 0.458,0.198 10 false e7 3.479,2.74 3.635,2.938 0.156,0.198 10 false 8 4.031,2.75 4.188,2.948 0.156,0.198 10 false 7 4.646,3.052 4.802,3.25 0.156,0.198 10 false 2 2.875,2.958 3.031,3.156 0.156,0.198 10 false 7 2.823,3.354 3.135,3.552 0.313,0.198 10 false 12 2.865,3.75 3.021,3.948 0.156,0.198 10 false 3

C294980E05
1.708,1.125 2.208,0.198 2.208,0.198 2.344,0.198 false 4.688,1.125 5.188,0.198 5.188,0.198 5.323,0.198 false 0.031,0.031 1.865,0.271 1.833,0.24 12 false Sub Bus 1 (for RHD): 5.385,0.104 6.625,0.74 1.24,0.635 10 false No. 5 CAN Junction Connector 2.396,0.094 3.635,0.729 1.24,0.635 10 false No. 6 CAN Junction Connector 0.708,2.01 1.479,2.208 0.771,0.198 10 false 120 Ω 6.156,2.01 6.927,2.208 0.771,0.198 10 false 120 Ω 5.833,2.635 6.958,3.063 1.125,0.427 10 false Multiplex Network Door ECU 0.198,2.635 1.844,3.792 1.646,1.156 10 false Main Body ECU (Multiplex Network Body ECU) 2.969,4.156 4.573,4.594 1.604,0.438 10 false Position Control ECU and Switch Assembly 1.125,5.063 5.104,5.26 3.979,0.198 10 false : CAN Main Bus Line (CANH) 4.26,5.063 6.052,5.313 1.792,0.25 10 false : CAN Branch Line (CANH) 1.01,3.656 2.844,3.854 1.833,0.198 10 false Trouble Area 1.125,5.396 5.104,5.594 3.979,0.198 10 false : CAN Main Bus Line (CANL) 4.26,5.396 6.073,5.708 1.813,0.313 10 false : CAN Branch Line (CANL) 1.969,4.115 3.552,4.302 1.583,0.188 10 false IG1 NO. 3 1.927,3.708 3.458,3.906 1.531,0.198 10 false MPX-B NO. 1 1.958,3.302 3.49,3.5 1.531,0.198 10 false P/SEAT F/R 3.385,3.125 4,3.323 0.615,0.198 10 false CANP 3.833,3.125 4.448,3.323 0.615,0.198 10 false CANN 4.177,3.26 4.635,3.458 0.458,0.198 10 false GND 3.104,3.156 3.417,3.354 0.313,0.198 10 false +B 3.094,3.563 3.708,3.76 0.615,0.198 10 false SYSB 3.104,3.948 3.417,4.146 0.313,0.198 10 false IG 2.813,3.167 3.271,3.365 0.458,0.198 10 false d6 3.51,2.927 3.969,3.125 0.458,0.198 10 false d7 3.917,2.927 4.375,3.125 0.458,0.198 10 false d7 4.615,3.25 5.073,3.448 0.458,0.198 10 false d6 2.823,3.552 3.281,3.75 0.458,0.198 10 false d7 2.833,3.938 3.292,4.135 0.458,0.198 10 false d7 3.479,2.729 3.635,2.927 0.156,0.198 10 false 8 4.031,2.729 4.188,2.927 0.156,0.198 10 false 7 4.646,3.073 4.802,3.271 0.156,0.198 10 false 2 2.875,2.948 3.031,3.146 0.156,0.198 10 false 7 2.823,3.365 3.135,3.563 0.313,0.198 10 false 12 2.865,3.75 3.021,3.948 0.156,0.198 10 false 3

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON and wait at least 20 seconds.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.RECONFIRM DTC OUTPUT
Body Electrical > Main Body > Trouble Codes
50001 123
a.

Reconfirm DTCs.

HINT:

If DTC U1002 is output from Main Body of the main body ECU (multiplex network body ECU), this indicates a sub bus 1 malfunction. Troubleshoot for DTC U1002 and check for malfunctions in sub bus 1.



Result:
Result Proceed to
DTC U1002 is not output from main body ECU (multiplex network body ECU) (GTS display: Main Body) A
DTC U1002 is output from main body ECU (multiplex network body ECU) (GTS display: Main Body) B



A

2.CHECK FOR OPEN IN SUB BUS 1 LINES (POSITION CONTROL ECU AND SWITCH ASSEMBLY BRANCH LINE)

B

GO TO DIAGNOSIS PROCEDURE INDICATED BY OUTPUT DTC

2.CHECK FOR OPEN IN SUB BUS 1 LINES (POSITION CONTROL ECU AND SWITCH ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the d7 or e7 position control ECU and switch assembly connector.


c.
C285244C42
0.365,0.74 0.771,0.979 0.406,0.24 0.365,1.115 0.771,1.354 0.406,0.24 0.833,1.885 1.063,1.885 1.063,1.885 1.333,1.458 true 1.917,1.875 1.698,1.875 1.698,1.875 1.51,1.458 true 0.198,0.125 0.51,0.281 0.313,0.156 10 false *a 1.969,1.781 2.583,1.979 0.615,0.198 10 false CANP 0.427,1.792 1.042,1.99 0.615,0.198 10 false CANN 0.5,0.76 1.115,0.958 0.615,0.198 10 false e7 0.5,1.135 0.813,1.333 0.313,0.198 10 false d7 0.844,0.75 1.219,0.99 0.375,0.24 12 false *A 0.844,1.125 1.219,1.365 0.375,0.24 12 false *B
*A for LHD
*B for RHD
*a Front view of wire harness connector
(to Position Control ECU and Switch Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
e7-8 (CANP) - e7-7 (CANN) Cable disconnected from negative (-) battery terminal 54 to 69 Ω

for RHD
Tester Connection Condition Specified Condition
d7-8 (CANP) - d7-7 (CANN) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY)

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Disconnect the d6 or e6 position control ECU and switch assembly connector.


b.
C287154C07
0.302,0.719 0.677,0.99 0.375,0.271 0.302,1.073 0.677,1.344 0.375,0.271 1.344,0.948 1.521,0.469 1.521,0.469 1.615,0.469 true 0.094,0.073 0.406,0.271 0.313,0.198 10 false *a 0.417,0.74 0.875,0.938 0.458,0.198 10 false e6 1.708,0.375 2.167,0.573 0.458,0.198 10 false GND 0.417,1.104 0.729,1.302 0.313,0.198 10 false d6 0.719,0.729 1.094,0.969 0.375,0.24 12 false *A 0.729,1.073 1.104,1.313 0.375,0.24 12 false *B
*A for LHD
*B for RHD
*a Front view of wire harness connector
(to Position Control ECU and Switch Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
e6-2 (GND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
d6-2 (GND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



c.

Reconnect the cable to the negative (-) battery terminal.


d.
C285280C12
0.271,0.417 0.667,0.708 0.396,0.292 0.323,2.083 0.708,2.375 0.385,0.292 0.323,2.438 0.708,2.729 0.385,0.292 0.271,0.792 0.667,1.083 0.396,0.292 1.073,2.969 1.208,2.969 1.208,2.969 1.385,2.604 true 2.479,1.51 2.354,1.51 2.354,1.51 2.125,1.188 true 1.635,0.813 2.427,0.438 2.427,0.438 2.583,0.438 true 0.396,0.438 0.854,0.635 0.458,0.198 10 false e7 0.438,2.115 0.896,2.313 0.458,0.198 10 false e6 0.094,0.083 0.406,0.281 0.313,0.198 10 false *a 0.865,2.875 1.177,3.073 0.313,0.198 10 false +B 2.531,1.417 3.146,1.615 0.615,0.198 10 false SYSB 2.635,0.344 2.948,0.542 0.313,0.198 10 false IG 0.406,0.833 0.865,1.031 0.458,0.198 10 false d7 0.438,2.469 0.896,2.667 0.458,0.198 10 false d6 0.75,0.417 1.125,0.656 0.375,0.24 12 false *A 0.75,2.104 1.125,2.344 0.375,0.24 12 false *A 0.75,0.802 1.125,1.042 0.375,0.24 12 false *B 0.75,2.448 1.125,2.688 0.375,0.24 12 false *B
*A for LHD
*B for RHD
*a Front view of wire harness connector
(to Position Control ECU and Switch Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Condition Specified Condition
e6-7 (+B) - Body ground Always 11 to 14 V
e7-3 (IG) - Body ground Ignition switch ON 11 to 14 V
e7-12 (SYSB) - Body ground Always 11 to 14 V

for RHD
Tester Connection Condition Specified Condition
d6-7 (+B) - Body ground Always 11 to 14 V
d7-3 (IG) - Body ground Ignition switch ON 11 to 14 V
d7-12 (SYSB) - Body ground Always 11 to 14 V



Result:
Result
OK
NG



OK

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)