Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM3160E _57 Power Source / Network _019704 NETWORKING _0095663 CAN COMMUNICATION SYSTEM C

NETWORKING  CAN COMMUNICATION SYSTEM  U0199  Lost Communication with "Door Control Module A"  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Note
U0199 Lost Communication with "Door Control Module A" No communication from the outer mirror control ECU assembly continues.
·

Outer mirror control ECU assembly branch line or connector

·

Power source circuit of outer mirror control ECU assembly

·

Outer mirror control ECU assembly ground circuit

·

Outer mirror control ECU assembly


HINT:

Main body ECU (multiplex network body ECU) stores DTCs when it detects a communication stop or network communication error for ECUs connected to sub bus 1.



HINT:

This diagnosis procedure is for when DTC U0199 is output by the main body ECU (multiplex network body ECU) (GTS display: Main Body).


WIRING DIAGRAM

C294979E01
1.729,1.125 2.354,0.146 2.354,0.146 2.469,0.146 false 4.698,1.125 5.323,0.146 5.323,0.146 5.438,0.146 false 0.042,0.042 1.875,0.281 1.833,0.24 12 false Sub Bus 1 (for LHD): 0.719,2.01 1.49,2.208 0.771,0.198 10 false 120 Ω 6.135,2 6.906,2.198 0.771,0.198 10 false 120 Ω 2.542,0.052 3.771,0.698 1.229,0.646 10 false No. 6 CAN Junction Connector 5.521,0.063 6.75,0.708 1.229,0.646 10 false No. 5 CAN Junction Connector 0.115,2.656 1.771,3.583 1.656,0.927 10 false Main Body ECU (Multiplex Network Body ECU) 5.833,2.635 6.938,3.083 1.104,0.448 10 false Multiplex Network Door ECU 3.104,3.583 3.563,3.781 0.458,0.198 10 false SIG 3.094,3.208 3.708,3.406 0.615,0.198 10 false CPUB 1.958,3.365 3.49,3.563 1.531,0.198 10 false MPX-B NO. 1 1.958,3.729 3.792,3.927 1.833,0.198 10 false IG1 NO. 3 2.917,3.979 5.115,5.219 2.198,1.24 10 false Outer Mirror Control ECU Assembly (for Front Passenger Side) 2.677,3.979 2.99,4.177 0.313,0.198 10 false H2 3.417,2.958 4.031,3.156 0.615,0.198 10 false CANP 3.865,2.969 4.479,3.167 0.615,0.198 10 false CANN 4.177,3.26 4.635,3.458 0.458,0.198 10 false GND 4.542,3.135 4.698,3.333 0.156,0.198 10 false 7 4.031,2.771 4.188,2.969 0.156,0.198 10 false 8 3.458,2.781 3.615,2.979 0.156,0.198 10 false 9 2.927,3.104 3.083,3.302 0.156,0.198 10 false 6 2.938,3.49 3.094,3.688 0.156,0.198 10 false 5 3.333,4.625 5.167,4.823 1.833,0.198 10 false Trouble Area 1.125,5.063 5.104,5.26 3.979,0.198 10 false : CAN Main Bus Line (CANH) 1.125,5.396 5.104,5.594 3.979,0.198 10 false : CAN Main Bus Line (CANL) 4.26,5.063 5.948,5.333 1.688,0.271 10 false : CAN Branch Line (CANH) 4.26,5.396 5.979,5.667 1.719,0.271 10 false : CAN Branch Line (CANL)

C294979E03
1.729,1.125 2.354,0.146 2.354,0.146 2.469,0.146 false 4.698,1.125 5.323,0.146 5.323,0.146 5.438,0.146 false 0.042,0.042 1.875,0.281 1.833,0.24 12 false Sub Bus 1 (for RHD): 0.719,2.01 1.49,2.208 0.771,0.198 10 false 120 Ω 6.135,2 6.906,2.198 0.771,0.198 10 false 120 Ω 2.542,0.052 3.771,0.698 1.229,0.646 10 false No. 6 CAN Junction Connector 5.521,0.063 6.75,0.708 1.229,0.646 10 false No. 5 CAN Junction Connector 0.115,2.656 1.771,3.583 1.656,0.927 10 false Main Body ECU (Multiplex Network Body ECU) 5.833,2.635 6.958,3.104 1.125,0.469 10 false Multiplex Network Door ECU 3.104,3.573 3.563,3.771 0.458,0.198 10 false SIG 3.104,3.219 3.719,3.417 0.615,0.198 10 false CPUB 1.958,3.365 3.49,3.563 1.531,0.198 10 false MPX-B NO. 1 1.938,3.729 3.771,3.927 1.833,0.198 10 false IG1 NO. 3 2.917,3.979 5.115,5.219 2.198,1.24 10 false Outer Mirror Control ECU Assembly (for Driver Side) 2.677,3.979 2.99,4.177 0.313,0.198 10 false H2 3.417,2.958 4.031,3.156 0.615,0.198 10 false CANP 3.865,2.969 4.479,3.167 0.615,0.198 10 false CANN 4.177,3.26 4.635,3.458 0.458,0.198 10 false GND 4.542,3.135 4.698,3.333 0.156,0.198 10 false 7 4.031,2.771 4.188,2.969 0.156,0.198 10 false 8 3.458,2.781 3.615,2.979 0.156,0.198 10 false 9 2.927,3.115 3.083,3.313 0.156,0.198 10 false 6 2.917,3.479 3.073,3.677 0.156,0.198 10 false 5 3.333,4.625 5.167,4.823 1.833,0.198 10 false Trouble Area 1.125,5.063 5.104,5.26 3.979,0.198 10 false : CAN Main Bus Line (CANH) 1.125,5.396 5.104,5.594 3.979,0.198 10 false : CAN Main Bus Line (CANL) 4.26,5.063 5.948,5.333 1.688,0.271 10 false : CAN Branch Line (CANH) 4.26,5.396 5.979,5.667 1.719,0.271 10 false : CAN Branch Line (CANL)

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON and wait at least 20 seconds.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.RECONFIRM DTC OUTPUT
Body Electrical > Main Body > Trouble Codes
50001 123
a.

Reconfirm DTCs.

HINT:

If DTC U1002 is output from Main Body of the main body ECU (multiplex network body ECU), this indicates a sub bus 1 malfunction. Troubleshoot for DTC U1002 and check for malfunctions in sub bus 1.



Result:
Result Proceed to
DTC U1002 is not output from main body ECU (multiplex network body ECU) (GTS display: Main Body) A
DTC U1002 is output from main body ECU (multiplex network body ECU) (GTS display: Main Body) B



A

2.CHECK FOR OPEN IN SUB BUS 1 LINES (OUTER MIRROR CONTROL ECU ASSEMBLY BRANCH LINE)

B

GO TO DIAGNOSIS PROCEDURE INDICATED BY OUTPUT DTC

2.CHECK FOR OPEN IN SUB BUS 1 LINES (OUTER MIRROR CONTROL ECU ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the H2 outer mirror control ECU assembly connector.


c.
C285247C18
1.5,0.125 1.865,0.375 0.365,0.25 1.885,1.958 1.625,1.958 1.625,1.958 1.396,1.354 true 0.656,1.969 0.885,1.969 0.885,1.969 1.24,1.365 true 0.094,0.094 0.406,0.25 0.313,0.156 10 false *a 1.604,0.156 2.063,0.354 0.458,0.198 10 false H2 0.24,1.875 0.698,2.073 0.458,0.198 10 false CANN 1.938,1.865 2.396,2.063 0.458,0.198 10 false CANP
*a Front view of wire harness connector
(to Outer Mirror Control ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H2-9 (CANP) - H2-8 (CANN) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (OUTER MIRROR CONTROL ECU ASSEMBLY)

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C285247C20
1.5,0.115 1.865,0.365 0.365,0.25 2.896,0.854 2.76,0.854 2.76,0.854 2.25,1.052 true 0.104,0.094 0.417,0.25 0.313,0.156 10 false *a 1.604,0.156 2.063,0.354 0.458,0.198 10 false H2 2.948,0.771 3.406,0.969 0.458,0.198 10 false GND
*a Front view of wire harness connector
(to Outer Mirror Control ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H2-7 (GND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.


c.
C285247C19
1.5,0.115 1.865,0.365 0.365,0.25 2.906,0.583 2.792,0.583 2.792,0.583 2.063,1.063 true 2.813,0.313 2.552,0.313 2.552,0.313 1.896,1.063 true 0.104,0.094 0.417,0.25 0.313,0.156 10 false *a 1.604,0.146 2.063,0.344 0.458,0.198 10 false H2 2.948,0.49 3.406,0.688 0.458,0.198 10 false CPUB 2.854,0.219 3.313,0.417 0.458,0.198 10 false SIG
*a Front view of wire harness connector
(to Outer Mirror Control ECU Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H2-5 (SIG) - Body ground Ignition switch ON 11 to 14 V
H2-6 (CPUB) - Body ground Always 11 to 14 V



Result:
Result
OK
NG



OK

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)