Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM
RM3160E _59 Vehicle Exterior _019721 WIPER / WASHER _0097860 WIPER AND WASHER SYSTEM J

WIPER / WASHER  WIPER AND WASHER SYSTEM  Wiper ECU Power Source Circuit  


DESCRIPTION

This circuit provides power to the windshield wiper relay assembly.

WIRING DIAGRAM

E289377E01
0.51,0.552 1.469,0.948 0.958,0.396 10 false from IG1 NO. 1 Relay 0.469,1.51 1.427,1.906 0.958,0.396 10 false from IG1 NO. 2 Relay 2.063,0.74 2.802,0.948 0.74,0.208 10 false WIPER FR 2.167,1.688 2.906,1.896 0.74,0.208 10 false ECU-IG 0.396,2.427 0.646,2.594 0.25,0.167 10 false 4A 3.156,0.427 3.406,0.594 0.25,0.167 10 false 10 3.177,1.396 3.427,1.563 0.25,0.167 10 false 29 5.24,0.448 5.385,0.615 0.146,0.167 10 false 2 5.438,0.583 5.656,0.76 0.219,0.177 10 false IG 5.448,1.5 5.813,1.698 0.365,0.198 10 false WIG 5.208,1.417 5.427,1.583 0.219,0.167 10 false 16 5.208,1.896 5.427,2.063 0.219,0.167 10 false 12 5.448,2 5.813,2.198 0.365,0.198 10 false E 0.396,2.583 3.188,2.865 2.792,0.281 10 false Instrument Panel Junction Block Assembly 5.031,2.448 6.51,2.771 1.479,0.323 10 false Windshield Wiper Relay Assembly 5.021,2.26 5.365,2.427 0.344,0.167 10 false F79

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK WINDSHIELD WIPER RELAY ASSEMBLY (IG POWER SOURCE CIRCUIT)
a.

Disconnect the F79 windshield wiper relay assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F79-2 (IG) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
F79-16 (WIG) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

2.CHECK WINDSHIELD WIPER RELAY ASSEMBLY (GROUND CIRCUIT)

NG

3.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
2.CHECK WINDSHIELD WIPER RELAY ASSEMBLY (GROUND CIRCUIT)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F79-12 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 4A instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F79-2 (IG) - 4A-10 Always Below 1 Ω
F79-16 (WIG) - 4A-29 Always Below 1 Ω
F79-2 (IG) or 4A-10 - Body ground Always 10 kΩ or higher
F79-16 (WIG) or 4A-29 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR