Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM › 2013.12–2016.11
RM3160E _59 Vehicle Exterior _019721 WIPER / WASHER _0097860 WIPER AND WASHER SYSTEM J

WIPER / WASHER  WIPER AND WASHER SYSTEM  IG Power Source Circuit  


DESCRIPTION

This circuit provides power to the headlight cleaner control relay.

WIRING DIAGRAM

E288751
4.938,2.354 6.917,2.646 1.979,0.292 10 false Headlight Cleaner Control Relay 4.958,2.219 5.292,2.396 0.333,0.177 10 false A41 5.26,1.188 5.458,1.385 0.198,0.198 10 false 3 5.458,1.792 5.656,1.99 0.198,0.198 10 false E 5.26,1.688 5.458,1.885 0.198,0.198 10 false 4 5.458,1.333 5.656,1.531 0.198,0.198 10 false IG 3.146,1.208 3.365,1.375 0.219,0.167 10 false 11 0.5,1.313 1.458,1.708 0.958,0.396 10 false from IG1 NO. 2 Relay 0.385,2.448 3.323,2.792 2.938,0.344 10 false Instrument Panel Junction Block Assembly 0.396,2.302 0.729,2.479 0.333,0.177 10 false 4F 2.208,1.458 2.76,1.677 0.552,0.219 10 false ECU-IG

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HEADLIGHT CLEANER CONTROL RELAY (IG POWER SOURCE CIRCUIT)
a.

Disconnect the A41 headlight cleaner control relay connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A41-3 (IG) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

2.CHECK HEADLIGHT CLEANER CONTROL RELAY (GROUND CIRCUIT)

NG

3.CHECK HARNESS AND CONNECTOR (HEADLIGHT CLEANER CONTROL RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
2.CHECK HEADLIGHT CLEANER CONTROL RELAY (GROUND CIRCUIT)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A41-4 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (HEADLIGHT CLEANER CONTROL RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 4F instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A41-3 (IG) - 4F-11 Always Below 1 Ω
A41-3 (IG) or 4F-11 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR