Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Smart Entry and Start System)
RM3160E _58 Vehicle Interior _019705 DOOR LOCK _0098501 WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Smart Entry and Start System) J

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Smart Entry and Start System)  No Answer-Back  


DESCRIPTION

In some cases, wireless door lock control functions are normal but the hazard warning light and wireless door lock buzzer answer-back functions do not operate. In such cases, hazard warning light and wireless door lock buzzer signal outputs from the main body ECU (multiplex network body ECU) may be malfunctioning.

WIRING DIAGRAM

B365054
3.583,3.313 5.26,3.729 1.677,0.417 10 false Main Body ECU (Multiplex Network Body ECU) 2.125,2.396 3.802,2.813 1.677,0.417 10 false Instrument Panel Junction Block Assembly 5.75,3.167 6.917,3.667 1.167,0.5 10 false Combination Meter Assembly 0.823,2.302 1.74,2.719 0.917,0.417 10 false Wireless Door Lock Buzzer 0.938,4.135 2.948,4.385 2.01,0.25 10 false : CAN Communication Line 0.823,2.135 1.417,2.438 0.594,0.302 10 false A31 2.115,2.229 2.365,2.479 0.25,0.25 10 false 4F 3.583,3.135 3.833,3.385 0.25,0.25 10 false MB 3.813,1.677 4.229,2.01 0.417,0.333 10 false BZR 2.438,1.573 2.854,1.906 0.417,0.333 10 false 30 3.552,1.563 3.969,1.896 0.417,0.333 10 false 21 1.917,1.552 2.333,1.885 0.417,0.333 10 false 1 0.594,1.573 1.01,1.906 0.417,0.333 10 false 2 0.792,1.677 1.208,2.01 0.417,0.333 10 false E 1.719,1.677 2.135,2.01 0.417,0.333 10 false B

CAUTION / NOTICE / HINT

NOTICE:
·

The wireless door lock control system key and reminder warning system use the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the wireless door lock control system after confirming that the communication system is functioning properly.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Smart Entry and Start System)>HOW TO PROCEED WITH TROUBLESHOOTING

·

As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

*: for LHD




PROCEDURE

1.READ VALUE USING GTS (Hazard Answer Back, Wireless Buzzer Resp, Wireless Buzzer Vol)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Customize Setting / Wireless Door Lock.


e.

Select the setting by referring to the table below.

Wireless Door Lock
Tester Display Description Default Setting ECU
Hazard Answer Back Function that flashes the hazard warning lights once when the doors are locked by wireless operation and twice when the doors are unlocked by wireless operation. ON 0:OFF,1:ON Main body ECU (Multiplex network body ECU)
Wireless Buzzer Resp Wireless door lock buzzer response* ON 0:OFF,1:ON Main body ECU (Multiplex network body ECU)
Wireless Buzzer Vol Wireless door lock buzzer volume* Level5 0000:Level7,0001:Level6,0010:Level5,0011:Level4,0100:Level3,0101:Level2,0110:Level1,0111:Level0 Main body ECU (Multiplex network body ECU)
50006 1

*: w/ Wireless Door Lock Buzzer Answer-back Function



Result:
Result Proceed to
Both items are ON and except Level 0 A
Either item is OFF or Level 0 B



A

2.CHECK WIRELESS DOOR LOCK CONTROL FUNCTIONS

B

2.CHECK WIRELESS DOOR LOCK CONTROL FUNCTIONS
a.

Check the wireless door lock control function using the door control transmitter module set sub-assembly.


Result:
Result Proceed to
Wireless door lock/unlock operates properly A
Wireless door lock/unlock does not operate properly B



A

3.READ VALUE USING GTS (FR Door Lock Pos, FL Door Lock Pos, RR-Door Lock Pos SW, RL-Door Lock Pos SW)

B

3.READ VALUE USING GTS (FR Door Lock Pos, FL Door Lock Pos, RR-Door Lock Pos SW, RL-Door Lock Pos SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Door Lock Pos Front door RH unlock detection switch signal LOCK or UNLOCK LOCK: Front door RH locked
UNLOCK: Front door RH unlocked
-
FL Door Lock Pos Front door LH unlock detection switch signal LOCK or UNLOCK LOCK: Front door LH locked
UNLOCK: Front door LH unlocked
-
RR-Door Lock Pos SW Rear door RH unlock detection switch signal OFF or ON OFF: Rear door RH locked
ON: Rear door RH unlocked
-
RL-Door Lock Pos SW Rear door RH unlock detection switch signal OFF or ON OFF: Rear door LH locked
ON: Rear door LH unlocked
-
Body Electrical > Main Body > Data List
Tester Display
FR Door Lock Pos
FL Door Lock Pos
RR-Door Lock Pos SW
RL-Door Lock Pos SW
50003 123 196,198,51,52
OK:

The GTS display changes correctly in response to the lock/unlock operation.



Result:
Proceed to
OK
NG



OK

4.CHECK WIRELESS ANSWER-BACK OPERATION

NG

GO TO LIGHTING SYSTEM (Proceed to Door Unlock Detection Switch Circuit)

4.CHECK WIRELESS ANSWER-BACK OPERATION
a.

Check the wireless answer-back operation using the door control transmitter module set sub-assembly.


Result:
Result Proceed to
Only wireless door lock buzzer answer-back does not occur A
Only hazard warning light answer-back does not occur B



A

5.PERFORM ACTIVE TEST USING GTS (Wireless Buzzer)

B

10.CHECK HAZARD WARNING LIGHTS OPERATION
5.PERFORM ACTIVE TEST USING GTS (Wireless Buzzer)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Restrict Condition
Wireless Buzzer Wireless door lock buzzer OFF/ON -
Body Electrical > Main Body > Active Test
Tester Display
Wireless Buzzer
50004 123 12

Result:
Result Proceed to
Wireless door lock buzzer does not turn on/off A
Wireless door lock buzzer turns on/off B



A

6.CHECK HARNESS AND CONNECTOR (WIRELESS DOOR LOCK BUZZER - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

6.CHECK HARNESS AND CONNECTOR (WIRELESS DOOR LOCK BUZZER - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the A31 wireless door lock buzzer connector.


b.

Disconnect the 4F instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A31-1 (B) - 4F-30 Always Below 1 Ω
A31-2 (E) - Body ground Always Below 1 Ω
A31-1 (B) or 4F-30 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL

B364844C01
5.365,0.719 5.823,0.99 0.458,0.271 2.156,0.938 2.615,1.208 0.458,0.271 2.49,2.229 2.688,2.229 2.688,2.229 2.688,1.677 false 0.302,0.281 0.615,0.479 0.313,0.198 10 false *a 5.51,0.76 5.823,0.958 0.313,0.198 10 false 4F 2.271,0.979 2.583,1.177 0.313,0.198 10 false MB 2.156,2.156 2.531,2.365 0.375,0.208 10 false BZR
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -



b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4F-30 - MB-21 (BZR) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

8.REPLACE WIRELESS DOOR LOCK BUZZER

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

8.REPLACE WIRELESS DOOR LOCK BUZZER
a.

Temporarily replace the wireless door lock buzzer with a new one.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK BUZZER>REMOVAL


Result:
Proceed to
NEXT



NEXT

9.CHECK WIRELESS DOOR LOCK BUZZER OPERATION
9.CHECK WIRELESS DOOR LOCK BUZZER OPERATION
a.

Check the operation of the wireless answer-back function.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Smart Entry and Start System)>OPERATION CHECK

OK:

Wireless answer-back function operates normally.



Result:
Proceed to
OK
NG



OK

END (WIRELESS DOOR LOCK BUZZER WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

10.CHECK HAZARD WARNING LIGHTS OPERATION
a.

Check that the hazard warning lights blink when the hazard warning signal switch is pressed.

OK:

Hazard warning lights blink.



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

GO TO LIGHTING SYSTEM (Proceed to Hazard Warning Switch Circuit)