Home › Power Source / Network › POWER DISTRIBUTION › MAIN BODY ECU
RM3160E _57 Power Source / Network _019703 POWER DISTRIBUTION _0100762 MAIN BODY ECU A

POWER DISTRIBUTION  MAIN BODY ECU  INSTALLATION  


PROCEDURE

Hide 1. PRECAUTION (w/ Smart Entry and Start System)

NOTICE:

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.


Hide 89221 2.INSTALL MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NOTICE:
·

Make sure that no foreign matter gets on the connecting surfaces.

·

Do not touch the main body ECU (multiplex network body ECU) connector.



a.

Set the main body ECU (multiplex network body ECU) to the position where the guide of the main body ECU (multiplex network body ECU) contacts the housing sidewall of the instrument panel junction block assembly as shown in the illustration.

B322925C01
1.49,1.125 1,0.823 true 4.833,0.906 4.354,0.656 true 0.49,0.198 0.885,0.406 0.396,0.208 12 false *A 3.823,0.219 4.208,0.469 0.385,0.25 12 false *B 0.729,1.875 1.042,2.031 0.313,0.156 10 false *a 0.802,0.719 1.115,0.875 0.313,0.156 10 false *b 4.063,1.656 4.375,1.813 0.313,0.156 10 false *a 4.177,0.563 4.49,0.719 0.313,0.156 10 false *b
*A for LHD *B for RHD
*a 20° or more *b Housing Sidewall


HINT:

Make sure to keep the angle at 20° or more as shown in the illustration.



b.

Slide the main body ECU (multiplex network body ECU) along the housing sidewall as shown in the illustration and engage the 2 guides.

B322926C01
0.76,0.896 1.417,1.104 true 3.885,0.708 4.542,0.917 true 0.594,0.25 1.01,0.573 0.417,0.323 12 false *A 3.865,0.25 4.292,0.5 0.427,0.25 12 false *B 0.573,0.792 0.885,0.948 0.313,0.156 10 false *a 3.688,0.594 4,0.75 0.313,0.156 10 false *a
*A for LHD *B for RHD
*a Housing Sidewall - -



c.

While keeping the main body ECU (multiplex network body ECU) in contact with side A of the instrument panel junction block assembly (axis of rotation), lower it as shown in the illustration.

B322927C01
2.365,0.646 3.073,0.542 true 5.552,0.521 6.26,0.417 true 3.125,0.438 3.438,0.594 0.313,0.156 10 false *a 6.302,0.323 6.615,0.479 0.313,0.156 10 false *a 0.917,0.104 1.292,0.344 0.375,0.24 12 false *A 3.969,0.104 4.344,0.344 0.375,0.24 12 false *B
*A for LHD *B for RHD
*a Side A - -



d.

Press the push area until the claw engages to install the main body ECU (multiplex network body ECU).

B322928C02
0.969,1 1.688,1.135 true 4.448,0.76 5.052,0.979 true 0.938,2.292 1.969,2.469 true 4.385,2.208 5,2.125 true 0.854,2.438 0.854,2.646 0.854,2.646 1.729,2.646 true 4.313,2.333 4.313,2.542 4.313,2.542 5.188,2.542 true 0.625,0.208 1.083,0.563 0.458,0.354 12 false *A 4.094,0.208 4.521,0.479 0.427,0.271 12 false *B 2.052,2.406 2.365,2.563 0.313,0.156 10 false *1 1.781,2.563 2.094,2.719 0.313,0.156 10 false *2 0.781,0.896 1.094,1.052 0.313,0.156 10 false *a 4.25,0.656 4.563,0.813 0.313,0.156 10 false *a 5.042,2.042 5.354,2.198 0.313,0.156 10 false *1 5.229,2.469 5.542,2.625 0.313,0.156 10 false *2
*A for LHD *B for RHD
*1 Instrument Panel Junction Block Assembly *2 Main Body ECU (Multiplex Network Body ECU)
*a Push Area - -


NOTICE:
·

Make sure to press only the push area.

·

Confirm the engagement of the main body ECU (multiplex network body ECU) and instrument panel junction block assembly by listening for the click sound of the lock engaging.



HINT:

If a click sound cannot be heard, visually check the engagement of the lock. The engagement can also be confirmed if the main body ECU (multiplex network body ECU) and instrument panel junction block assembly are flush.



Hide 3.INSTALL INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU (for LHD)

a.
B322897

Connect the connector and push down the lock lever to engage the claw and lock the connector as shown in the illustration.

NOTICE:

Be sure to connect the connector securely.



b.
B322895

Slide the connector lock to engage the claw as shown in the illustration.


c.
B322893

Connect the connector and push down the lock lever to engage the claw and lock the connector as shown in the illustration.

NOTICE:

Be sure to connect the connector securely.



d.
B322891

Engage the clamp as shown in the illustration.


e.
B322888

Install the instrument panel junction block assembly with main body ECU with the 2 nuts.


f.

Engage the clamp.


g.
B322887

Connect the connector and raise the lock lever to engage the claw and lock the connector as shown in the illustration.

NOTICE:

Be sure to connect the connector securely.



h.
B322885

Connect the connector and raise the lock lever to engage the claw and lock the connector as shown in the illustration.

NOTICE:

Be sure to connect the connector securely.



i.

Connect each connector.


Hide 4.INSTALL INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU (for RHD)

a.
B322921

Connect the connector and push down the lock lever to engage the claw and lock the connector as shown in the illustration.

NOTICE:

Be sure to connect the connector securely.



b.
B322919

Slide the connector lock to engage the claw as shown in the illustration.


c.
B322917

Connect the connector and push down the lock lever to engage the claw and lock the connector as shown in the illustration.

NOTICE:

Be sure to connect the connector securely.



d.
B322915

Engage the guide and claw to connect the connector holder as shown in the illustration.


e.
B364503

Engage the clamp as shown in the illustration.


f.
B322912C01
1.177,1.875 1.135,1.917 false
V100135

Bolt
V100136

Nut


Install the instrument panel junction block assembly with main body ECU with the 2 bolts and nut.


g.
B322910

Connect the connector and raise the lock lever to engage the claw and lock the connector as shown in the illustration.

NOTICE:

Be sure to connect the connector securely.



h.
B322908

Connect the connector and raise the lock lever to engage the claw and lock the connector as shown in the illustration.

NOTICE:

Be sure to connect the connector securely.



i.

Connect each connector.


Hide 55045 5.INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for LHD)

Hide 53601 6.CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY (for LHD)

Hide 55606 7.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for LHD)

Hide 55303B 8.INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY (for RHD)

Hide 55607 9.INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD)

Hide 55436A 10.INSTALL INSTRUMENT PANEL FINISH PANEL END LH

Hide 11.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

Hide 62112A 12.INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH

Hide 67914 13.INSTALL FRONT DOOR SCUFF PLATE LH

Hide 14.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION