1.INSTALL INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY
Engage the 5 guides to temporarily install the instrument panel safety pad sub-assembly as shown in the illustration.
Do not damage the instrument panel safety pad sub-assembly.
Do not allow the wire harnesses to interfere with the surrounding parts.
Install the instrument panel safety pad sub-assembly with the 6 bolts <C>, 2 bolts <A> and nut <E>.
Install the 2 clips.
Engage each clamp.
Install the screw <D>.
Connect each connector.
Engage the 2 claws to connect the room temperature sensor.
82142A
2.CONNECT NO. 2 INSTRUMENT PANEL WIRE
55434F
3.INSTALL CENTER LOWER INSTRUMENT PANEL FINISH PANEL
Connect each connector.
Engage the 2 claws as shown in the illustration.
Install the center lower instrument panel finish panel with the 2 bolts <C>, 2 screws <D> and 2 nuts <E>.
55446A
4.INSTALL NO. 1 SWITCH HOLE BASE
w/o Smart Key System:
Engage the 4 claws to install the No. 1 switch hole base.
w/ Smart Key System:
Connect the connector.
Engage the 4 claws to install the No. 1 switch hole base.
55660
5.INSTALL NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY
Engage the 3 guides and 4 claws to install the No. 2 instrument panel register assembly.
55445B
6.INSTALL INSTRUMENT PANEL FINISH PLATE
Engage the 3 guides and 6 claws as shown in the illustration.
Install the instrument panel finish panel with the 5 screws <D>.
55414A
7.INSTALL INSTRUMENT CLUSTER FINISH PANEL END
w/ Illumination
Connect the 2 connectors.
Engage the 3 guides and 11 claws to install the instrument cluster finish panel end as shown in the illustration.
55471A
8.INSTALL INSTRUMENT CLUSTER FINISH PANEL ORNAMENT
Engage the 8 claws and 6 clips to install the instrument cluster finish panel ornament.
55303B
9.INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY
Connect each connector.
Engage the guide and 3 clips as shown in the illustration.
Install the 2 bolts <B>.
Open the lower instrument panel sub-assembly door.
Install the lower instrument panel sub-assembly with the 3 screws <D>.
Close the lower instrument panel sub-assembly door.
55607
10.INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
Engage the 2 guides and 4 claws to install the No. 2 instrument panel under cover sub-assembly.
55435A
11.INSTALL INSTRUMENT PANEL FINISH PANEL END RH
w/ Airbag Cut Off Switch:
Connect the connector.
Engage the 3 guides and 5 claws to install the instrument panel finish panel end RH as shown in the illustration.
86160P
12.INSTALL FRONT NO. 2 SPEAKER ASSEMBLY (for RH Side)
Use the same procedure as for the LH side.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>INSTALLATION
55409F
13.INSTALL NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY
Engage the 2 guides and 2 clips to install the No. 2 instrument panel speaker panel sub-assembly as shown in the illustration.
62211
14.INSTALL FRONT PILLAR GARNISH RH
Use the same procedure as for the LH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION
15.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH
62111A
16.INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH
Use the same procedure as for the LH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION
67913
17.INSTALL FRONT DOOR SCUFF PLATE RH
Use the same procedure as for the LH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION
58816B
18.INSTALL CONSOLE BOX INSERT
for LHD:
Engage the 4 guides and claw as shown in the illustration.
Install the console box insert with the 2 screws <D> and 2 clips.
for RHD:
Engage the 4 guides and claw as shown in the illustration.
Install the console box insert with the 2 screws <D> and clip.
58817A
19.INSTALL FRONT NO. 2 CONSOLE BOX INSERT
Engage the 4 guides and claw as shown in the illustration.
Install the front No. 2 console box insert with the 2 screws <D> and clip.
Engage the clamp.
55446E
20.INSTALL NO. 2 SWITCH HOLE BASE
Connect each connector.
Engage the 4 claws to install the No. 2 switch hole base as shown in the illustration.
21.INSTALL CONSOLE BOX ASSEMBLY
83910
22.INSTALL CLOCK ASSEMBLY
23.INSTALL RADIO RECEIVER ASSEMBLY WITH BRACKET (for Radio and Display Type)
24.INSTALL NAVIGATION RECEIVER ASSEMBLY WITH BRACKET (for Navigation Receiver Type)
55680A
25.INSTALL NO. 4 INSTRUMENT PANEL REGISTER ASSEMBLY
Engage the guide and 5 claws to install the No. 4 instrument panel register assembly.
55670
26.INSTALL NO. 3 INSTRUMENT PANEL REGISTER ASSEMBLY
Engage the guide and 6 claws to install the No. 3 instrument panel register assembly.
55422C
27.INSTALL CENTER UPPER INSTRUMENT CLUSTER FINISH PANEL
Engage the guide and 8 claws to install the center upper instrument cluster finish panel.
28.INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL WITH AIR CONDITIONING CONTROL ASSEMBLY
Connect the connector.
Engage the connector clamp.
Engage the 17 claws to install the center instrument cluster finish panel with air conditioning control assembly.
86160J
29.INSTALL FRONT NO. 3 SPEAKER ASSEMBLY (for 12 Speakers)
55510F
30.INSTALL NO. 1 SPEAKER OPENING COVER ASSEMBLY (for 12 Speakers)
Engage the 2 guides and 4 clips to install the No. 1 speaker opening cover assembly.
55650
31.INSTALL NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY
Engage the 3 guides and 5 claws to install the No. 1 instrument panel register assembly.
55045
32.INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY
Connect each connector.
Engage the 10 claws and 4 clips.
Install the lower instrument panel finish panel sub-assembly with the bolt <B>.
53601
33.CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY
Engage the 2 guides and claw to connect the hood lock control lever sub-assembly.
55606
34.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
Connect each connector.
Engage the connector clamp.
Engage the guide, claw and clip.
Install the No. 1 instrument panel under cover sub-assembly with the 2 screws <D>.
55436A
35.INSTALL INSTRUMENT PANEL FINISH PANEL END LH
Engage the 3 guides and 5 claws to install the instrument panel finish panel end LH as shown in the illustration.
86160P
36.INSTALL FRONT NO. 2 SPEAKER ASSEMBLY (for LH Side)
55408F
37.INSTALL NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY
Engage the 2 guides and 2 clips to install the No. 1 instrument panel speaker panel sub-assembly as shown in the illustration.
62212
38.INSTALL FRONT PILLAR GARNISH LH
39.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH
62112A
40.INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH
67914
41.INSTALL FRONT DOOR SCUFF PLATE LH
42.INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY
45286B
43.INSTALL UPPER STEERING COLUMN COVER
45287
44.INSTALL LOWER STEERING COLUMN COVER
45.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD
84307
46.INSPECT AND ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY
45100
47.INSTALL STEERING WHEEL ASSEMBLY
45130
48.INSTALL HORN BUTTON ASSEMBLY
83100
49.INSTALL COMBINATION METER ASSEMBLY
50.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
51.CHECK STEERING WHEEL CENTER POINT
52. PERFORM DIAGNOSTIC SYSTEM CHECK
53.INSPECT SRS WARNING LIGHT