Home › Vehicle Interior › INTERIOR PANELS / TRIM › INSTRUMENT PANEL SAFETY PAD
RM3160E _58 Vehicle Interior _019716 INTERIOR PANELS / TRIM _0107106 INSTRUMENT PANEL SAFETY PAD A

INTERIOR PANELS / TRIM  INSTRUMENT PANEL SAFETY PAD  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 83100 4.REMOVE COMBINATION METER ASSEMBLY

Hide 45130 5.REMOVE HORN BUTTON ASSEMBLY

Hide 45100 6.REMOVE STEERING WHEEL ASSEMBLY

Hide 45287 7.REMOVE LOWER STEERING COLUMN COVER

Hide 45286B 8.REMOVE UPPER STEERING COLUMN COVER

Hide 9.REMOVE TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

Hide 67914 10.REMOVE FRONT DOOR SCUFF PLATE LH

Hide 62112A 11.REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH

Hide 12.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH

a.

Disconnect front door opening trim weatherstrip LH.


Hide 62212 13.REMOVE FRONT PILLAR GARNISH LH

Hide 55408F 14.REMOVE NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY

a.
B362306

Disengage the 2 clips and 2 guides, and remove the No. 1 instrument panel speaker panel sub-assembly as shown in the illustration.


Hide 86160P 15.REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (for LH Side)

Hide 55436A 16.REMOVE INSTRUMENT PANEL FINISH PANEL END LH

a.
B362300

Using a moulding remover, disengage the 5 claws and 3 guides, and remove the instrument panel finish panel end LH as shown in the illustration.


Hide 55606 17.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

a.
B362298

Remove the 2 screws <D>.


b.
B362299

Disengage the claw, clip and guide.


c.

Disengage the connector clamp.


d.

Disconnect each connector to remove the No. 1 instrument panel under cover sub-assembly.


Hide 53601 18.DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

a.
B362302

Disengage the claw and 2 guides to disconnect the hood lock control lever sub-assembly.


Hide 55045 19.REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY

a.
B362303

Remove the bolt <B>.


b.
B362304

Disengage the 10 claws and 4 clips.


c.

Disconnect each connector to remove the lower instrument panel finish panel sub-assembly.


Hide 55650 20.REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY

a.
B362305

Disengage the 5 claws and 3 guides to remove the No. 1 instrument panel register assembly.


Hide 55510F 21.REMOVE NO. 1 SPEAKER OPENING COVER ASSEMBLY (for 12 Speakers)

a.
B362348

Using a moulding remover, disengage the 4 clips and 2 guides to remove the No. 1 speaker opening cover assembly.


Hide 86160J 22.REMOVE FRONT NO. 3 SPEAKER ASSEMBLY (for 12 Speakers)

Hide 23.REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL WITH AIR CONDITIONING CONTROL ASSEMBLY

a.

Using a moulding remover, disengage the 17 claws as shown in the illustration.

B362317


b.

Disengage the connector clamp.


c.

Disconnect the connector and remove the center instrument cluster finish panel with air conditioning control assembly.


Hide 55422C 24.REMOVE CENTER UPPER INSTRUMENT CLUSTER FINISH PANEL

a.
B362319

Disengage the 8 claws and guide as shown in the illustration to remove the center upper instrument cluster finish panel.


Hide 55670 25.REMOVE NO. 3 INSTRUMENT PANEL REGISTER ASSEMBLY

a.
B362321

Disengage the 6 claws and guide as shown in the illustration to remove the No. 3 instrument panel register assembly.


Hide 55680A 26.REMOVE NO. 4 INSTRUMENT PANEL REGISTER ASSEMBLY

a.
B362323

Disengage the 5 claws and guide as shown in the illustration to remove the No. 4 instrument panel register assembly.


Hide 27.REMOVE RADIO RECEIVER ASSEMBLY WITH BRACKET (for Radio and Display Type)

Hide 28.REMOVE NAVIGATION RECEIVER ASSEMBLY WITH BRACKET (for Navigation Receiver Type)

Hide 83910 29.REMOVE CLOCK ASSEMBLY

Hide 55446E 31.REMOVE NO. 2 SWITCH HOLE BASE

a.
B362325

Disengage the 4 claws as shown in the illustration.


b.

Disconnect each connector to remove the No. 2 switch hole base.


Hide 58817A 32.REMOVE FRONT NO. 2 CONSOLE BOX INSERT

a.
B362327

Disengage the clamp.


b.
B362328

Remove the 2 screws <D> and clip.


c.
B362329

Disengage the claw and 4 guides, and remove the front No. 2 console box insert as shown in the illustration.


Hide 58816B 33.REMOVE CONSOLE BOX INSERT

a.

for LHD:

i.
B362331

Remove the 2 screws <D> and 2 clips.


ii.
B362332

Disengage the claw and 4 guides, and remove the console box insert as shown in the illustration.



b.

for RHD:

i.
B367493

Remove the 2 screws <D> and clip.


ii.
B367494

Disengage the claw and 4 guides, and remove the console box insert as shown in the illustration.



Hide 67913 34.REMOVE FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.


Hide 62111A 35.REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 36.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure as for the LH side.


Hide 62211 37.REMOVE FRONT PILLAR GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 55409F 38.REMOVE NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY

a.
B362315

Disengage the 2 clips and 2 guides, and remove the No. 2 instrument panel speaker panel sub-assembly as shown in the illustration.


Hide 86160P 39.REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (for RH Side)

HINT:

Use the same procedure as for the LH side.


Hide 55435A 40.REMOVE INSTRUMENT PANEL FINISH PANEL END RH

a.
B362308

Using a moulding remover, disengage the 5 claws and 3 guides, and remove the instrument panel finish panel end RH as shown in the illustration.


b.

w/ Airbag Cut Off Switch:

i.

Disconnect the connector.



Hide 55607 41.REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

a.
B362310

Disengage the 4 claws and 2 guides to remove the No. 2 instrument panel under cover sub-assembly.


Hide 55303B 42.REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY

a.

Open the lower instrument panel sub-assembly door.


b.
B362311

Remove the 3 screws <D>.


c.

Close the lower instrument panel sub-assembly door.


d.
B362312

Remove the 2 bolts <B>.


e.
B362313

Disengage the 3 clips and guide as shown in the illustration.


f.

Disconnect each connector and remove the lower instrument panel sub-assembly.


Hide 55471A 43.REMOVE INSTRUMENT CLUSTER FINISH PANEL ORNAMENT

a.

Disengage the 8 claws and 6 clips as shown in the illustration to remove the instrument cluster finish panel ornament.

B362334


Hide 55414A 44.REMOVE INSTRUMENT CLUSTER FINISH PANEL END

a.

Disengage the 11 claws and 3 guides, and remove the instrument cluster finish panel end as shown in the illustration.

B362336


b.

w/ Illumination

i.

Disconnect the 2 connectors.



Hide 55445B 45.REMOVE INSTRUMENT PANEL FINISH PLATE

a.

Remove the 5 screws <D>.

B362338


b.

Disengage the 6 claws and 3 guides, and remove the instrument panel finish plate as shown in the illustration.

B362339


Hide 55660 46.REMOVE NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY

a.
B362341

Disengage the 4 claws and 3 guides as shown in the illustration to remove the No. 2 instrument panel register assembly.


Hide 55446A 47.REMOVE NO. 1 SWITCH HOLE BASE

a.

w/o Smart Key System:

i.
B362344

Disengage the 4 claws to remove the No. 1 switch hole base.



b.

w/ Smart Key System:

i.
B362343

Disengage the 4 claws.


ii.

Disconnect the connector to remove the No. 1 switch hole base.



Hide 55434F 48.REMOVE CENTER LOWER INSTRUMENT PANEL FINISH PANEL

a.
B362345

Remove the 2 bolts <C>, 2 screws <D> and 2 nuts <E>.


b.
B362346

Disengage the 2 claws as shown in the illustration.


c.

Disconnect each connector and remove the center lower instrument panel finish panel.


Hide 82142A 49.DISCONNECT NO. 2 INSTRUMENT PANEL WIRE

Hide 50.REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY

a.

Disengage the 2 claws to disconnect the room temperature sensor.

B362350C01
3.75,5.823 3.906,6.281 true 3.99,6.167 4.229,6.375 0.24,0.208 10 true *1
*1 Room Temperature Sensor - -



b.

Disconnect each connector.


c.

Remove the screw <D>.


d.

Disengage each clamp.


e.

Remove the 6 bolts <C>, 2 bolts <A> and nut <E>.

B362351C01
6.073,2.875 7.042,2.875 7.042,2.875 7.042,2.292 false 6.323,2.583 6.323,2.875 false 6.729,2.417 6.729,2.875 false 5.323,5.219 4.635,5.542 4.635,5.542 6.708,5.125 true 4.427,5.469 4.74,5.625 0.313,0.156 10 true *a 2.208,4.667 2.521,4.823 0.313,0.156 10 true *b 3.396,3.052 3.667,3.24 0.271,0.188 10 true *c 0.813,1.052 1.063,1.25 0.25,0.198 10 true *d 4.365,3.656 4.677,3.813 0.313,0.156 10 true *b 5.875,3.26 6.188,3.417 0.313,0.156 10 true *b 5.719,2.823 6.031,2.979 0.313,0.156 10 true *b 5.99,0.479 6.24,0.677 0.25,0.198 10 true *d
*a Bolt <A> *b Bolt <C>
*c Nut <E> *d Clip



f.

Remove the 2 clips.


g.

Disengage the 5 guides and remove the instrument panel safety pad sub-assembly as shown in the illustration.

B362352

NOTICE:
·

Do not damage the instrument panel safety pad sub-assembly.

·

Do not allow the wire harnesses to interfere with the surrounding parts.