Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM3160E _58 Vehicle Interior _019710 SUPPLEMENTAL RESTRAINT SYSTEMS _0100809 AIRBAG SYSTEM J

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  Trouble in Passenger Airbag ON/OFF Indicator  


DESCRIPTION

This circuit detects the airbag cut off switch cylinder sub-assembly status.

The passenger airbag ON/OFF indicator comes on to inform the instrument panel passenger airbag assembly and front seat airbag sub-assembly RH status (activated or deactivated).

HINT:

Approximately 6 seconds after the ignition switch is turned to ON, the passenger airbag ON/OFF indicator will indicate ON/OFF depending on the conditions listed below.

Airbag Cut Off Switch Cylinder Sub-assembly Passenger Airbag ON/OFF Indicator SRS Warning Light
ON Indicator OFF Indicator
ON ON OFF OFF
OFF OFF ON OFF
Switch failure OFF ON ON


WIRING DIAGRAM

C263693E04
5.354,0.688 5.76,1.042 0.406,0.354 10 false 11 5.354,2.167 5.76,2.521 0.406,0.354 10 false 12 5.604,0.792 6.135,1.167 0.531,0.375 10 false MSW+ 5.604,2.271 6.135,2.646 0.531,0.375 10 false MSW- 5.583,2.938 5.99,3.292 0.406,0.354 10 false F38 5.583,3.115 7.135,3.552 1.552,0.438 10 false Airbag Sensor Assembly 0.583,3.115 3.396,3.448 2.813,0.333 10 false Airbag Cut Off Switch Cylinder Sub-assembly 0.583,2.938 0.99,3.292 0.406,0.354 10 false F89 2.875,0.688 3.281,1.042 0.406,0.354 10 false 1 2.875,2.156 3.281,2.51 0.406,0.354 10 false 2 2.385,0.688 2.865,1.042 0.479,0.354 10 false PMC+ 2.417,2.156 2.896,2.51 0.479,0.354 10 false PMC-

CAUTION / NOTICE / HINT

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


HINT:

Terminals K51-11 (MSW+) and K51-12 (MSW-) of the instrument panel wire in this circuit have an activation prevention mechanism.

This mechanism can be used to check for an open circuit in the wire harness. In case of other checks (check for short, short to ground or short to B+), this mechanism should be released.


PROCEDURE

1.CHECK SRS WARNING LIGHT
a.

Turn the ignition switch to ON, and check the SRS warning light condition.

OK:

After the primary check period, the SRS warning light goes off.


HINT:
·

If the SRS warning light is on when this malfunction occurs, a DTC is stored. Troubleshoot for the stored DTC.

·

The primary check period is approximately 6 seconds after the ignition switch is turned to ON.




Result:
Proceed to
OK
NG



OK

2.CHECK CONNECTORS

NG

2.CHECK CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag sensor assembly and airbag cut off switch cylinder sub-assembly.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag sensor assembly and airbag cut off switch cylinder sub-assembly.


e.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.



f.

Check that the short spring for the instrument panel wire connector with the activation prevention mechanism is not deformed or damaged.

OK:

The short spring is not deformed or damaged.



Result:
Proceed to
OK
NG



OK

3.CHECK INSTRUMENT PANEL WIRE (OPEN)

NG

REPLACE INSTRUMENT PANEL WIRE

3.CHECK INSTRUMENT PANEL WIRE (OPEN)
a.
C285483C02
0.698,2.167 1.01,2.396 0.313,0.229 1.583,0.698 1.583,0.281 1.583,0.281 1.75,0.281 false 1.208,2.813 1.604,2.479 false 2.281,2.813 1.906,2.469 false 0.49,0.698 0.833,1 0.344,0.302 10 false *1 2.667,0.698 2.979,1.01 0.313,0.313 10 false *2 1.781,0.198 2.094,0.438 0.313,0.24 10 false *3 0.448,1.604 0.813,1.875 0.365,0.271 10 false *a 1,2.833 1.5,3.229 0.5,0.396 10 false PMC+ 2.146,2.833 2.667,3.083 0.521,0.25 10 false PMC- 0.74,2.198 1.156,2.448 0.417,0.25 10 false F89 2.292,0.698 2.604,1.01 0.313,0.313 10 false A 1.844,0.698 2.156,1.01 0.313,0.313 10 false B 1.219,0.698 1.531,1.01 0.313,0.313 10 false C 0.771,0.688 1.083,1 0.313,0.313 10 false D
*1 Airbag Cut Off Switch Cylinder Sub-assembly
*2 Airbag Sensor Assembly
*3 Instrument Panel Wire
*a Front view of wire harness connector
(to Airbag Cut Off Switch Cylinder Sub-assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F89-1 (PMC+) - F89-2 (PMC-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK INSTRUMENT PANEL WIRE (SHORT)

NG

REPLACE INSTRUMENT PANEL WIRE

4.CHECK INSTRUMENT PANEL WIRE (SHORT)
a.
C285483C02
0.698,2.167 1.01,2.396 0.313,0.229 1.583,0.698 1.583,0.281 1.583,0.281 1.75,0.281 false 1.208,2.813 1.604,2.479 false 2.281,2.813 1.906,2.469 false 0.49,0.698 0.833,1 0.344,0.302 10 false *1 2.667,0.698 2.979,1.01 0.313,0.313 10 false *2 1.781,0.198 2.094,0.438 0.313,0.24 10 false *3 0.448,1.604 0.813,1.875 0.365,0.271 10 false *a 1,2.833 1.5,3.229 0.5,0.396 10 false PMC+ 2.146,2.833 2.667,3.083 0.521,0.25 10 false PMC- 0.74,2.198 1.156,2.448 0.417,0.25 10 false F89 2.292,0.698 2.604,1.01 0.313,0.313 10 false A 1.844,0.698 2.156,1.01 0.313,0.313 10 false B 1.219,0.698 1.531,1.01 0.313,0.313 10 false C 0.771,0.688 1.083,1 0.313,0.313 10 false D
*1 Airbag Cut Off Switch Cylinder Sub-assembly
*2 Airbag Sensor Assembly
*3 Instrument Panel Wire
*a Front view of wire harness connector
(to Airbag Cut Off Switch Cylinder Sub-assembly)


Release the activation prevention mechanism built into connector B.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F89-1 (PMC+) - F89-2 (PMC-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)

NG

REPLACE INSTRUMENT PANEL WIRE

5.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)
a.
C285483C02
0.698,2.167 1.01,2.396 0.313,0.229 1.583,0.698 1.583,0.281 1.583,0.281 1.75,0.281 false 1.208,2.813 1.604,2.479 false 2.281,2.813 1.906,2.469 false 0.49,0.698 0.833,1 0.344,0.302 10 false *1 2.667,0.698 2.979,1.01 0.313,0.313 10 false *2 1.781,0.198 2.094,0.438 0.313,0.24 10 false *3 0.448,1.604 0.813,1.875 0.365,0.271 10 false *a 1,2.833 1.5,3.229 0.5,0.396 10 false PMC+ 2.146,2.833 2.667,3.083 0.521,0.25 10 false PMC- 0.74,2.198 1.156,2.448 0.417,0.25 10 false F89 2.292,0.698 2.604,1.01 0.313,0.313 10 false A 1.844,0.698 2.156,1.01 0.313,0.313 10 false B 1.219,0.698 1.531,1.01 0.313,0.313 10 false C 0.771,0.688 1.083,1 0.313,0.313 10 false D
*1 Airbag Cut Off Switch Cylinder Sub-assembly
*2 Airbag Sensor Assembly
*3 Instrument Panel Wire
*a Front view of wire harness connector
(to Airbag Cut Off Switch Cylinder Sub-assembly)


Connect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F89-1 (PMC+) - Body ground Ignition switch ON Below 1 V
F89-2 (PMC-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

6.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)

NG

REPLACE INSTRUMENT PANEL WIRE

6.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)
a.
C285483C02
0.698,2.167 1.01,2.396 0.313,0.229 1.583,0.698 1.583,0.281 1.583,0.281 1.75,0.281 false 1.208,2.813 1.604,2.479 false 2.281,2.813 1.906,2.469 false 0.49,0.698 0.833,1 0.344,0.302 10 false *1 2.667,0.698 2.979,1.01 0.313,0.313 10 false *2 1.781,0.198 2.094,0.438 0.313,0.24 10 false *3 0.448,1.604 0.813,1.875 0.365,0.271 10 false *a 1,2.833 1.5,3.229 0.5,0.396 10 false PMC+ 2.146,2.833 2.667,3.083 0.521,0.25 10 false PMC- 0.74,2.198 1.156,2.448 0.417,0.25 10 false F89 2.292,0.698 2.604,1.01 0.313,0.313 10 false A 1.844,0.698 2.156,1.01 0.313,0.313 10 false B 1.219,0.698 1.531,1.01 0.313,0.313 10 false C 0.771,0.688 1.083,1 0.313,0.313 10 false D
*1 Airbag Cut Off Switch Cylinder Sub-assembly
*2 Airbag Sensor Assembly
*3 Instrument Panel Wire
*a Front view of wire harness connector
(to Airbag Cut Off Switch Cylinder Sub-assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F89-1 (PMC+) - Body ground Always 1 MΩ or higher
F89-2 (PMC-) - Body ground Always 1 MΩ or higher



b.

Restore the released activation prevention mechanism of connector B to the original condition.


Result:
Proceed to
OK
NG



OK

7.CHECK AIRBAG CUT OFF SWITCH CYLINDER SUB-ASSEMBLY

NG

REPLACE INSTRUMENT PANEL WIRE

7.CHECK AIRBAG CUT OFF SWITCH CYLINDER SUB-ASSEMBLY
a.
C261687C04
2.302,1.052 2.729,0.771 false 2.292,1.135 2.729,1.417 false 0.073,0.063 0.354,0.365 0.281,0.302 10 false *a 2.781,0.698 3.25,1.042 0.469,0.344 10 false PMC- 2.792,1.333 3.26,1.677 0.469,0.344 10 false PMC+
*a Component without harness connected
(Airbag Cut Off Switch Cylinder Sub-assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (PMC+) - 2 (PMC-) Cut off switch in ON position 360 to 440 Ω
1 (PMC+) - 2 (PMC-) Cut off switch in OFF position 90 to 110 Ω



Result:
Proceed to
OK
NG



OK

NG

REPLACE AIRBAG CUT OFF SWITCH CYLINDER SUB-ASSEMBLY