Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM
RM3160E _58 Vehicle Interior _019705 DOOR LOCK _0098499 POWER DOOR LOCK CONTROL SYSTEM J

DOOR LOCK  POWER DOOR LOCK CONTROL SYSTEM  Power Source Circuit  


DESCRIPTION

The main power source for the main body ECU (multiplex network body ECU) is supplied via the door control battery.

WIRING DIAGRAM

B363415E02
1.323,0.656 2.354,1.073 1.031,0.417 10 false from Battery 1.323,1.073 2.396,1.406 1.073,0.333 10 false from Battery 2.76,0.802 3.219,1 0.458,0.198 10 false D/L 2.354,1.229 3.292,1.469 0.938,0.24 10 false MPX-B NO. 1 3.167,0.552 3.323,0.75 0.156,0.198 10 false 5 3.167,0.979 3.323,1.177 0.156,0.198 10 false 4 3.344,0.667 3.958,0.865 0.615,0.198 10 false BATB 3.354,1.083 3.969,1.281 0.615,0.198 10 false BECU 3.354,1.885 3.969,2.083 0.615,0.198 10 false EDOR 4.563,1.375 5.177,1.573 0.615,0.198 10 false GND1 4.563,1.813 5.177,2.01 0.615,0.198 10 false GND2 3.458,2.365 3.771,2.563 0.313,0.198 10 false F88 3.469,2.51 5.042,2.75 1.573,0.24 10 false Door Control Battery 3.167,1.781 3.479,1.979 0.313,0.198 10 false 3 5.031,1.281 5.344,1.479 0.313,0.198 10 false 2 5.01,1.729 5.323,1.927 0.313,0.198 10 false 10 5.292,3.833 5.906,4.031 0.615,0.198 10 false BECU 4.948,3.833 5.26,4.031 0.313,0.198 10 false MB 4.969,3.625 5.271,3.865 0.302,0.24 10 false 31 5.24,4.792 6.896,5.177 1.656,0.385 10 false Main Body ECU (Multiplex Network Body ECU) 2.448,4.583 5.135,4.906 2.688,0.323 10 false Instrument Panel Junction Block Assembly 2.469,3.833 2.844,4.063 0.375,0.229 10 false 4D 2.479,3.625 2.823,3.927 0.344,0.302 10 false 23

CAUTION / NOTICE / HINT

NOTICE:
·

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.*

*: w/ Smart Entry and Start System


·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After performing the following inspection, perform Initialization.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (DOOR CONTROL BATTERY - BATTERY AND BODY GROUND)
a.

Disconnect the F88 door control battery connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F88-5 (BATB) - Body ground Always 11 to 14 V
F88-4 (BECU) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F88-2 (GND1) - Body ground Always Below 1 Ω
F88-10 (GND2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (DOOR CONTROL BATTERY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (DOOR CONTROL BATTERY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 4D instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F88-3 (EDOR) - 4D-23 Always Below 1 Ω
F88-3 (EDOR) or 4D-23 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT DOOR CONTROL BATTERY (POWER OUTPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT DOOR CONTROL BATTERY (POWER OUTPUT)
a.

Reconnect the F88 door control battery connector.


b.

Turn the ignition switch off.


c.

Remove the MPX-B NO. 1 fuse and leave the vehicle as is for 50 minutes.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F88-3 (EDOR) - Body ground Ignition switch OFF Below 2 V



Result:
Proceed to
OK
NG



OK

4.INSPECT DOOR CONTROL BATTERY (INTERNAL CIRCUIT)

NG

REPLACE DOOR CONTROL BATTERY

4.INSPECT DOOR CONTROL BATTERY (INTERNAL CIRCUIT)
a.

Reconnect the F88 door control battery connector.


b.

Install the MPX-B NO. 1 fuse.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F88-3 (EDOR) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPLACE DOOR CONTROL BATTERY

5.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU).

B346817C03
2.083,0.917 2.385,1.135 0.302,0.219 5.5,0.688 5.802,0.896 0.302,0.208 3.646,2.198 3.813,2.198 3.813,2.198 3.813,1.615 false 0.302,0.25 0.615,0.448 0.313,0.198 10 false *a 2.135,0.948 2.448,1.146 0.313,0.198 10 false MB 5.563,0.719 5.875,0.917 0.313,0.198 10 false 4D 3.229,2.125 3.823,2.417 0.594,0.292 10 false BECU
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
MB-31 (BECU) - 4D-23 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY