Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM
RM3160E _58 Vehicle Interior _019705 DOOR LOCK _0098499 POWER DOOR LOCK CONTROL SYSTEM J

DOOR LOCK  POWER DOOR LOCK CONTROL SYSTEM  Collision Door Lock Release Function does not Operate  


DESCRIPTION

When an impact is detected, a relay inside the door control battery is operated to switch the power source of the door lock with motor assemblies from the vehicle battery to the door control battery.

WIRING DIAGRAM

B363416E01
1.333,1.583 1.646,1.781 0.313,0.198 10 false IG 1.604,1.458 1.76,1.656 0.156,0.198 10 false 8 1.115,3.323 1.615,3.542 0.5,0.219 10 false ACTG 0.427,3.969 0.74,4.167 0.313,0.198 10 false F88 0.427,4.135 1.781,4.375 1.354,0.24 10 false Door Control Battery 4.021,1.583 5.49,2.083 1.469,0.5 10 false from IG1 NO. 3 Relay 2.719,2.313 5.458,2.688 2.74,0.375 10 false Instrument Panel Junction Block Assembly 5.208,3.99 6.865,4.417 1.656,0.427 10 false Main Body ECU (Multiplex Network Body ECU) 5.042,3.323 5.354,3.521 0.313,0.198 10 false F18 5.115,3.115 5.427,3.313 0.313,0.198 10 false 3 5.427,3.333 5.927,3.552 0.5,0.219 10 false ACTG 2.406,1.583 2.844,2 0.438,0.417 10 false 4A 2.406,1.385 2.844,1.802 0.438,0.417 10 false 51 3.073,1.76 4.094,2.146 1.021,0.385 10 false IG1 NO. 3 1.594,3.208 1.75,3.406 0.156,0.198 10 false 9

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.*

*: w/ Smart Entry and Start System


·

As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in How to Proceed with Troubleshooting to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

*: for LHD




PROCEDURE

1.CHECK DOOR LOCK OPERATION
a.

Check door lock operation.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK

OK:

All doors lock and unlock normally.



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (DOOR CONTROL BATTERY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

NG

2.CHECK HARNESS AND CONNECTOR (DOOR CONTROL BATTERY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the F88 door control battery connector.


b.

Disconnect the F18 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F88-9 (ACTG) - F18-3 (ACTG) Always Below 1 Ω
F88-9 (ACTG) or F18-3 (ACTG) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (DOOR CONTROL BATTERY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (DOOR CONTROL BATTERY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 4A instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F88-8 (IG) - 4A-51 Always Below 1 Ω
F88-8 (IG) or 4A-51 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (IG1 NO. 3 RELAY POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (IG1 NO. 3 RELAY POWER SOURCE)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
4A-51 - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.REPLACE DOOR CONTROL BATTERY

NG

GO TO LIGHTING SYSTEM (IG Signal Circuit)

5.REPLACE DOOR CONTROL BATTERY
a.

Replace the door control battery.

Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL BATTERY>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CHECK DOOR CONTROL BATTERY
6.CHECK DOOR CONTROL BATTERY
a.

Check door control battery operation.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

OK:

Collision detection door lock function operates normally.



Result:
Proceed to
OK
NG



OK

END (DOOR CONTROL BATTERY WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)