Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM › 2013.12–2016.11
RM3160E _51 Engine / Hybrid System _019662 2GR-FE ENGINE CONTROL _0101052 SFI SYSTEM C

2GR-FE ENGINE CONTROL  SFI SYSTEM  P0617  Starter Relay Circuit High  


MONITOR DESCRIPTION

While the engine is being cranked, battery voltage is applied to terminal STA of the ECM.

If the ECM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores this DTC.

This monitor runs when the vehicle is driven at 20 km/h (12.43 mph) or more for 20 seconds or more.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0617 Starter Relay Circuit High All of the following conditions are met, and a (+B) battery voltage of 10.5 V or higher is applied to the ECM for 20 seconds (1 trip detection logic).

(a) The vehicle speed is 20 km/h (12.43 mph) or more.

(b) The engine speed is 1000 rpm or higher.

(c) The STA signal is on.


·

Park/neutral position switch assembly

·

ST relay circuit

·

ECM


Comes on DTC stored

MONITOR STRATEGY

Required Sensors/Components (Main) ST relay
Park/neutral position switch assembly
Ignition switch assembly
Certification ECU (smart key ECU assembly)
Required Sensors/Components (Related) Vehicle speed sensor
Crankshaft position sensor
Frequency of Operation Continuous

TYPICAL ENABLING CONDITIONS

Vehicle speed 20 km/h (12.43 mph) or more
Engine speed 1000 rpm or higher

TYPICAL MALFUNCTION THRESHOLDS

Starter signal On

CONFIRMATION DRIVING PATTERN

A231469E24
1.229,1.979 1.656,2.198 0.427,0.219 10 Idling 0.396,2.26 1.604,2.583 1.208,0.323 10 Ignition Switch ON 1.063,0.865 1.635,1.073 0.573,0.208 10 24 km/h 2.396,2.854 3.083,3.167 0.688,0.313 10 5 seconds or more 3.594,2.938 4.865,3.104 1.271,0.167 10 20 seconds or more 2.01,2.333 2.302,2.552 0.292,0.219 10 [A] 2.615,2.125 2.823,2.302 0.208,0.177 10 [B] 4.063,0.458 4.292,0.625 0.229,0.167 10 [C] 4.885,3.333 5.115,3.5 0.229,0.167 10 [D]

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on [A].

6.

Start the engine.

7.

Idle the engine for 5 seconds or more [B].

8.

Drive the vehicle at 24 km/h (15 mph) or more for 20 seconds or more [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


9.

Enter the following menus: Powertrain / Engine / Trouble Codes [D].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: P0617.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.




WIRING DIAGRAM

A315015E03
0.094,0.073 3.76,0.313 3.667,0.24 12 false w/ Smart Entry and Start System: 0.188,2.635 1.99,3.042 1.802,0.406 10 false Certification ECU (Smart key ECU Assembly) 0.198,2.469 0.656,2.667 0.458,0.198 10 false F10 1.479,0.792 1.938,0.99 0.458,0.198 10 false NE 1.302,1.594 1.76,1.792 0.458,0.198 10 false STAR 1.396,2.125 1.854,2.323 0.458,0.198 10 false STA 1.781,0.656 2.24,0.854 0.458,0.198 10 false 14 1.802,1.469 2.26,1.667 0.458,0.198 10 false 10 1.802,1.99 2.26,2.188 0.458,0.198 10 false 12 5.396,0.594 5.854,0.792 0.458,0.198 10 false 22 5.344,0.781 5.802,0.979 0.458,0.198 10 false A43 5.688,0.667 6.146,0.865 0.458,0.198 10 false NEO 5.698,1.406 6.156,1.604 0.458,0.198 10 false NSW 5.375,1.594 5.833,1.792 0.458,0.198 10 false C1 5.344,3.781 5.802,3.979 0.458,0.198 10 false A43 5.396,1.406 5.854,1.604 0.458,0.198 10 false 65 5.427,3.583 5.885,3.781 0.458,0.198 10 false 9 5.688,3.656 6.146,3.854 0.458,0.198 10 false STA 6.125,4.948 6.583,5.146 0.458,0.198 10 false ECM 3.719,2.25 4.177,2.448 0.458,0.198 10 false L 4.354,2.25 4.813,2.448 0.458,0.198 10 false B 4.552,2.24 5.01,2.438 0.458,0.198 10 false 4 3.531,2.24 3.99,2.438 0.458,0.198 10 false 9 3.365,2.583 3.823,2.781 0.458,0.198 10 false C14 3.365,2.75 4.688,3.26 1.323,0.51 10 false Park/Neutral Position Switch Assembly 3.031,4.135 3.49,4.333 0.458,0.198 10 false 2 3.021,5.052 3.479,5.25 0.458,0.198 10 false 1 2.552,4.125 3.01,4.323 0.458,0.198 10 false 5 2.552,5.042 3.01,5.24 0.458,0.198 10 false 3 3.271,4.615 3.729,4.813 0.458,0.198 10 false ST 1.74,5.51 2.198,5.708 0.458,0.198 10 false C18 1.073,5.917 1.531,6.115 0.458,0.198 10 false D2 1.75,5.313 2.208,5.51 0.458,0.198 10 false 1 1.104,5.729 1.563,5.927 0.458,0.198 10 false 1 1.458,6.74 2.115,7.219 0.656,0.479 10 false Starter Assembly 0.74,6.792 1.396,7.271 0.656,0.479 10 false Battery 0.583,4.781 1.24,5.26 0.656,0.479 10 false FL MAIN 0.583,3.844 1.24,4.323 0.656,0.479 10 false ST 5.677,6.198 6.135,6.396 0.458,0.198 10 false STA 5.667,5.781 6.125,5.979 0.458,0.198 10 false NSW 6.021,7.417 6.479,7.615 0.458,0.198 10 false TCM 5.74,7.417 6.198,7.615 0.458,0.198 10 false C3 5.417,6.104 5.875,6.302 0.458,0.198 10 false 10 5.427,5.698 5.885,5.896 0.458,0.198 10 false 11

A315016E03
0.083,0.115 3.938,0.354 3.854,0.24 12 false w/o Smart Entry and Start System: 1.531,1.188 1.99,1.385 0.458,0.198 10 false AM1 2.115,1.188 2.573,1.385 0.458,0.198 10 false ST1 2.125,1.594 2.583,1.792 0.458,0.198 10 false ST2 1.531,1.604 1.99,1.802 0.458,0.198 10 false AM2 1.354,1.177 1.813,1.375 0.458,0.198 10 false 5 1.354,1.594 1.813,1.792 0.458,0.198 10 false 4 2.458,1.167 2.917,1.365 0.458,0.198 10 false 6 2.458,1.594 2.917,1.792 0.458,0.198 10 false 2 1.479,2.063 1.938,2.26 0.458,0.198 10 false F50 1.479,2.219 2.396,2.656 0.917,0.438 10 false Ignition Switch Assembly 3.344,2.323 3.802,2.521 0.458,0.198 10 false C14 5.375,1.281 5.833,1.479 0.458,0.198 10 false C1 5.385,1.104 5.844,1.302 0.458,0.198 10 false 65 5.688,1.115 6.146,1.313 0.458,0.198 10 false NSW 5.677,3.448 6.135,3.646 0.458,0.198 10 false STA 5.344,3.552 5.802,3.75 0.458,0.198 10 false A43 5.417,3.375 5.875,3.573 0.458,0.198 10 false 9 6.052,4.729 6.51,4.927 0.458,0.198 10 false ECM 3.719,2.042 4.177,2.24 0.458,0.198 10 false L 4.354,2.042 4.813,2.24 0.458,0.198 10 false B 3.344,2.5 4.677,3.031 1.333,0.531 10 false Park/Neutral Position Switch Assembly 3.531,2.031 3.99,2.229 0.458,0.198 10 false 9 4.563,2.021 5.021,2.219 0.458,0.198 10 false 4 0.573,2.896 0.906,3.396 0.333,0.5 10 false ST 1.104,2.875 1.563,3.073 0.458,0.198 10 false AM1 1.094,3.635 1.552,3.833 0.458,0.198 10 false ALT 0.573,4.875 1.51,5.177 0.938,0.302 10 false FL MAIN 1.75,5.292 2.208,5.49 0.458,0.198 10 false C18 1.073,5.698 1.531,5.896 0.458,0.198 10 false D2 1.115,5.51 1.573,5.708 0.458,0.198 10 false 1 1.74,5.094 2.198,5.292 0.458,0.198 10 false 1 3.01,4.833 3.469,5.031 0.458,0.198 10 false 1 2.542,4.833 3,5.031 0.458,0.198 10 false 3 2.552,3.906 3.01,4.104 0.458,0.198 10 false 5 3.031,3.917 3.49,4.115 0.458,0.198 10 false 2 3.281,4.354 3.74,4.552 0.458,0.198 10 false ST 1.479,6.521 2.125,7.042 0.646,0.521 10 false Starter Assembly 0.74,6.594 1.677,6.896 0.938,0.302 10 false Battery 5.688,6.031 6.146,6.229 0.458,0.198 10 false STA 5.688,5.594 6.146,5.792 0.458,0.198 10 false NSW 6.052,7.219 6.51,7.417 0.458,0.198 10 false TCM 5.813,7.219 6.271,7.417 0.458,0.198 10 false C3 5.427,5.906 5.885,6.104 0.458,0.198 10 false 10 5.438,5.49 5.896,5.688 0.458,0.198 10 false 11

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / All Data / Starter Signal.

Powertrain > Engine > Data List
Tester Display
Starter Signal
50003 234 118

e.

Check the value displayed on the GTS when the vehicle is driven at 20 km/h (12.43 mph) or more.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


Result:
Condition Starter Signal Result
Driving at 20 km/h (12.4 mph) or more OFF A
ON B




A

B

2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

Result:
Result Proceed to
OK (w/ Smart Entry and Start System) A
OK (w/o Smart Entry and Start System) B
NG C



A

3.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)

B

4.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)

C

3.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)
a.

Repair or replace the harness or connector (park/neutral position switch assembly - ST relay - ECM - TCM - certification ECU (smart key ECU assembly)).


Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (DTC P0617)
4.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)
a.

Repair or replace the harness or connector (park/neutral position switch assembly - ST relay - TCM - ECM).


Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (DTC P0617)
5.CHECK WHETHER DTC OUTPUT RECURS (DTC P0617)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 234
Result:
Result Proceed to
DTC P0617 is output A
DTCs are not output B




A

B

END