Home › Vehicle Exterior › MIRROR (EXT) › POWER MIRROR CONTROL SYSTEM(w/o Memory)
RM3160E _59 Vehicle Exterior _019720 MIRROR (EXT) _0101073 POWER MIRROR CONTROL SYSTEM(w/o Memory) J

MIRROR (EXT)  POWER MIRROR CONTROL SYSTEM(w/o Memory)  Mirror Heater does not Operate with Rear Defogger Switch  


DESCRIPTION

When the mirror heater switch (rear window defogger switch) on the air conditioning control assembly is pressed, the operation signal is sent to the air conditioning amplifier assembly via LIN communication. When the air conditioning amplifier assembly receives the signal, it turns on a relay in the semiconductor power integration ECU to operate the mirror heaters.

WIRING DIAGRAM

B364874E05
0.396,0.792 1.229,0.99 0.833,0.198 10 false from Battery 0.115,3.385 0.948,3.583 0.833,0.198 10 false from Battery 0.115,3.948 0.948,4.146 0.833,0.198 10 false from Battery 0.052,4.563 1.01,4.979 0.958,0.417 10 false from IG1 NO. 3 Relay 1.594,0.969 2.667,1.167 1.073,0.198 10 false MIR HTR 0.833,1.5 1.906,1.698 1.073,0.198 10 false IDLE UP 1.417,4.125 2.49,4.323 1.073,0.198 10 false ALT 1.26,4.719 2.333,4.917 1.073,0.198 10 false IG1 NO. 3 2.094,2.635 2.25,2.833 0.156,0.198 10 false 1 2.094,3.167 2.25,3.365 0.156,0.198 10 false 1 2.094,3.75 2.25,3.948 0.156,0.198 10 false 1 2.063,4.323 2.25,4.521 0.188,0.198 10 false 11 2.052,2.875 2.333,3.094 0.281,0.219 10 false 1C 2.052,3.406 2.333,3.625 0.281,0.219 10 false 1H 2.052,3.969 2.333,4.188 0.281,0.219 10 false 2A 2.052,4.552 2.333,4.771 0.281,0.219 10 false 1D 2.385,2.865 2.833,3.083 0.448,0.219 10 false RDEF 2.385,3.406 2.833,3.625 0.448,0.219 10 false BATT 2.385,3.938 2.833,4.156 0.448,0.219 10 false ALT 2.385,4.51 2.833,4.729 0.448,0.219 10 false IGN 2.917,3.031 3.365,3.25 0.448,0.219 10 false GND1 2.927,3.604 3.375,3.823 0.448,0.219 10 false GND2 2.927,4.302 3.542,4.594 0.615,0.292 10 false DEFS 0.76,6.552 5.802,6.75 5.042,0.198 10 false Air Conditioning Control Assembly 0.75,7.354 4.417,7.552 3.667,0.198 10 false : LIN Communication Line 4.583,6.771 6.906,6.969 2.323,0.198 10 false Air Conditioning Amplifier Assembly 4.583,6.615 4.865,6.833 0.281,0.219 10 false F80 4.667,5.448 4.948,5.667 0.281,0.219 10 false 38 4.927,5.583 6,5.781 1.073,0.198 10 false RDFG 6.219,5.917 6.417,6.167 0.198,0.25 10 false 14 3.438,3.021 3.719,3.24 0.281,0.219 10 false 1D 3.427,4.302 3.708,4.521 0.281,0.219 10 false 1D 3.427,3.604 3.708,3.823 0.281,0.219 10 false 1G 3.448,2.802 3.688,3 0.24,0.198 10 false 14 3.479,3.375 3.719,3.573 0.24,0.198 10 false 5 3.49,4.094 3.729,4.292 0.24,0.198 10 false 5 2.25,4.917 3.5,5.333 1.25,0.417 10 false Semiconductor Pwr Integration ECU 2.25,0.667 2.49,0.865 0.24,0.198 10 false 5 3.26,0.677 3.417,0.875 0.156,0.198 10 false 3 2.25,1.219 2.406,1.417 0.156,0.198 10 false 2 3.25,1.219 3.406,1.417 0.156,0.198 10 false 1 4.49,0.667 4.646,0.865 0.156,0.198 10 false 2 6.667,0.667 6.823,0.865 0.156,0.198 10 false 9 5.094,0.698 5.25,0.896 0.156,0.198 10 false 1 6.021,0.688 6.177,0.885 0.156,0.198 10 false 2 5.167,1.135 7.156,1.333 1.99,0.198 10 false Outer Mirror RH 5.167,3.25 7.156,3.448 1.99,0.198 10 false Outer Mirror LH 4.583,1.667 6.958,1.875 2.375,0.208 10 false Outer Rear View Mirror Assembly RH 4.583,1.5 4.865,1.719 0.281,0.219 10 false H1 4.667,3.667 4.948,3.885 0.281,0.219 10 false I1 4.667,3.833 7.052,4.021 2.385,0.188 10 false Outer Rear View Mirror Assembly LH 5.802,6.083 6.25,6.302 0.448,0.219 10 false GND 4.719,0.667 4.875,0.865 0.156,0.198 10 false + 6.427,0.667 6.583,0.865 0.156,0.198 10 false E 4.719,2.802 4.875,3 0.156,0.198 10 false + 4.51,2.802 4.667,3 0.156,0.198 10 false 2 6.427,2.802 6.583,3 0.156,0.198 10 false E 6.677,2.802 6.833,3 0.156,0.198 10 false 9 5.094,2.802 5.25,3 0.156,0.198 10 false 1 6.01,2.802 6.167,3 0.156,0.198 10 false 2 2.531,1.74 3.24,2.042 0.708,0.302 10 false MIR HTR 4.938,6.104 6.01,6.302 1.073,0.198 10 false LIN1 4.698,5.948 4.979,6.167 0.281,0.219 10 false 37 2.49,5.938 2.771,6.156 0.281,0.219 10 false 8 2.115,6.104 3.188,6.302 1.073,0.198 10 false LIN1 0.76,6.385 1.042,6.604 0.281,0.219 10 false F32

CAUTION / NOTICE / HINT

NOTICE:
·

If the battery voltage is low, the mirror heater function may not operate. In this case, check the Data List item "Battery Control Count (Body ECU)".

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>DATA LIST / ACTIVE TEST

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Air Conditioner / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Air Conditioner > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Defogger Relay (Rear) Mirror heater operation OFF or ON -
Body Electrical > Air Conditioner > Active Test
Tester Display
Defogger Relay (Rear)
50004 121 22
Result:
Result Proceed to
Mirror heater operation on both mirrors is not normal A
Mirror heater operation on RH side mirror is not normal B
Mirror heater operation on LH side mirror is not normal C




A

2.CHECK WINDOW DEFOGGER SYSTEM

B

7.CHECK HARNESS AND CONNECTOR (MIR HTR RELAY - OUTER REAR VIEW MIRROR ASSEMBLY RH - BODY GROUND)

C

9.CHECK HARNESS AND CONNECTOR (MIR HTR RELAY - OUTER REAR VIEW MIRROR ASSEMBLY LH - BODY GROUND)
2.CHECK WINDOW DEFOGGER SYSTEM
a.

Check the window defogger system operation.

Click hereVehicle Exterior>WINDOW / GLASS>WINDOW DEFOGGER SYSTEM>OPERATION CHECK

OK:

The window defogger system operates normally.



Result:
Proceed to
OK
NG



OK

3.INSPECT MIR HTR RELAY

NG

3.INSPECT MIR HTR RELAY
a.

Remove the MIR HTR relay from the relay block No. 5.


b.

Inspect the MIR HTR relay.

Click hereVehicle Exterior>MIRROR (EXT)>RELAY>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (MIR HTR RELAY - SEMICONDUCTOR PWR INTEGRATION ECU)

NG

REPLACE MIR HTR RELAY

4.CHECK HARNESS AND CONNECTOR (MIR HTR RELAY - SEMICONDUCTOR PWR INTEGRATION ECU)
a.
B340809C05
0.146,0.125 0.458,0.281 0.313,0.156 10 false *1
*1 Relay Block No. 5


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Relay block No. 5 MIR HTR relay terminal 2 - 1C-1 (RDEF) Always Below 1 Ω
Relay block No. 5 MIR HTR relay terminal 2 or 1C-1 (RDEF) - Body ground Always 10 kΩ or higher
Relay block No. 5 MIR HTR relay terminal 1 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (MIR HTR RELAY POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (MIR HTR RELAY POWER SOURCE)
a.
B340809C05
0.146,0.125 0.458,0.281 0.313,0.156 10 false *1
*1 Relay Block No. 5


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Relay block No. 5 MIR HTR relay terminal 2 - Body ground Ignition switch ON, rear defogger switch on 11 to 14 V
Relay block No. 5 MIR HTR relay terminal 5 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (MIR HTR RELAY - OUTER REAR VIEW MIRROR ASSEMBLY RH/LH - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (MIR HTR RELAY - OUTER REAR VIEW MIRROR ASSEMBLY RH/LH - BODY GROUND)
a.

Disconnect the H1 outer rear view mirror assembly RH connector.


b.

Disconnect the I1 outer rear view mirror assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Relay block No. 5 MIR HTR relay terminal 3 - H1-2 (+) Always Below 1 Ω
Relay block No. 5 MIR HTR relay terminal 3 - I1-2 (+) Always Below 1 Ω
H1-2 (+), I1-2 (+) or Relay block No. 5 MIR HTR relay terminal 3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (MIR HTR RELAY - OUTER REAR VIEW MIRROR ASSEMBLY RH - BODY GROUND)
a.
B340809C05
0.146,0.125 0.458,0.281 0.313,0.156 10 false *1
*1 Relay Block No. 5


Remove the MIR HTR relay from relay block No. 5.


b.

Disconnect the H1 outer rear view mirror assembly RH connector.


c.

Disconnect the I1 outer rear view mirror assembly LH connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Relay block No. 5 MIR HTR relay terminal 3 - H1-2 (+) Always Below 1 Ω
H1-9 (E) - Body Ground Always Below 1 Ω
Relay block No. 5 MIR HTR relay terminal 3 or H1-2 (+) - Body Ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.INSPECT OUTER MIRROR RH (MIRROR HEATER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT OUTER MIRROR RH (MIRROR HEATER)

b.

Inspect the outer mirror RH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR GLASS>INSPECTION

OK:

Outer mirror RH is normal.



Result:
Proceed to
OK
NG



OK

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH

NG

9.CHECK HARNESS AND CONNECTOR (MIR HTR RELAY - OUTER REAR VIEW MIRROR ASSEMBLY LH - BODY GROUND)
a.
B340809C05
0.146,0.125 0.458,0.281 0.313,0.156 10 false *1
*1 Relay Block No. 5


Remove the MIR HTR relay from the relay block No. 5.


b.

Disconnect the H1 outer rear view mirror assembly RH connector.


c.

Disconnect the I1 outer rear view mirror assembly LH connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Relay block No. 5 MIR HTR relay terminal 3 - I1-2 (+) Always Below 1 Ω
I1-9 (E) - Body Ground Always Below 1 Ω
Relay block No. 5 MIR HTR relay terminal 3 or I1-2 (+) - Body Ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.INSPECT OUTER MIRROR LH (MIRROR HEATER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.INSPECT OUTER MIRROR LH (MIRROR HEATER)

b.

Inspect the outer mirror LH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR GLASS>INSPECTION

OK:

Outer mirror LH is normal.



Result:
Proceed to
OK
NG



OK

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH

NG