Home › Steering › STEERING COLUMN › STEERING LOCK SYSTEM
RM3160E _55 Steering _019698 STEERING COLUMN _0101123 STEERING LOCK SYSTEM C

STEERING COLUMN  STEERING LOCK SYSTEM  B2781  Open / Short in Steering Lock ECU  


DESCRIPTION

The steering lock ECU and steering lock motor are built into the steering lock actuator assembly.

The steering lock ECU (steering lock actuator assembly) detects whether the steering lock is in the lock or unlock position by using the lock sensor and unlock sensor of the steering lock motor.

The steering lock ECU (steering lock actuator assembly) receives lock and unlock request signals from the certification ECU (smart key ECU assembly) and responds with lock and unlock operation signals.

HINT:

The steering lock ECU (steering lock actuator assembly) is not connected to the CAN communication system. However, the steering lock ECU (steering lock actuator assembly) is connected to the certification ECU (smart key ECU assembly) via LIN communication and communicates with other components via CAN communication through the certification ECU (smart key ECU assembly).


DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2781 Open / Short in Steering Lock ECU One of the following conditions is met (1-trip detection logic (Only output while a malfunction is present and the engine switch is on (IG).)):
·

The steering lock sensor or unlock sensor is malfunctioning (When both detection switches turn on, the system is determined to be malfunctioning.).

·

The steering lock motor activation circuit has a short circuit.

·

The steering lock motor activation circuit has an open circuit.


·

Steering lock ECU (Steering lock actuator assembly)

·

LIN communication system


DTC Output Confirmation Operation: No confirmation operation is necessary (monitoring is continuous).

C221981
3.146,1.115 3.896,1.646 0.75,0.531 1.625,2.313 2.375,2.844 0.75,0.531 2.458,2.896 2.594,3.021 0.135,0.125 5.156,2.896 5.292,3.021 0.135,0.125 2.135,2.313 2.802,1.906 2.802,1.906 4.156,1.906 false 3.521,1.646 3.854,1.906 false 0.24,3.542 0.677,3.542 false 0.885,1.094 1.219,1.271 0.333,0.177 10 ON 0.885,1.406 1.219,1.583 0.333,0.177 10 OFF 0.885,2.302 1.219,2.479 0.333,0.177 10 ON 0.885,2.615 1.219,2.792 0.333,0.177 10 OFF 0.146,0.646 1.271,0.885 1.125,0.24 10 Unlock Sensor 0.156,1.979 1.115,2.271 0.958,0.292 10 Lock Sensor 1.594,3.073 3.667,3.26 2.073,0.188 10 Lock operation conditions met 4.104,3.083 6.396,3.26 2.292,0.177 10 Unlock operation conditions met 4.219,1.844 5.01,2.615 0.792,0.771 10 Example of Malfunction 0.719,3.448 2.938,3.646 2.219,0.198 10 : Normal operation

Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
The steering cannot be locked or unlocked. For this reason, the engine cannot be started. Prohibits the engine from being started (the engine does not crank).

Related Data List and Active Test Items
DTC No. Data List Item Active Test Item
B2781
Entry&Start
·

Sensor Value

·

Motor Driver Short


-

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry & Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

After performing repairs, confirm that no DTCs are output again.

Click hereSteering>STEERING COLUMN>STEERING LOCK SYSTEM>DTC CHECK / CLEAR

·

When replacing the steering lock ECU (steering lock actuator assembly), registration must be performed (refer to Service Bulletin).



HINT:

When all the ECUs that are connected via LIN communication cannot communicate with the certification ECU (smart key ECU assembly), DTC B2785 is stored.


PROCEDURE

1.CHECK DTC
a.

Using the GTS, check if LIN communication DTC B2785 is output.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

HINT:

If a LIN communication DTC is output, perform troubleshooting for the LIN communication system.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING



Result:
Result Proceed to
DTC B2785 is output. A
DTC B2785 is not output. B



A

GO TO LIN COMMUNICATION SYSTEM (DTC B2785)

B

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)