Home › Steering › STEERING COLUMN › STEERING LOCK SYSTEM
RM3160E _55 Steering _019698 STEERING COLUMN _0101123 STEERING LOCK SYSTEM C

STEERING COLUMN  STEERING LOCK SYSTEM  B2788  IG2 Signal Malfunction  


DESCRIPTION

This DTC is stored when the steering lock ECU (steering lock actuator assembly) detects an IG2 power supply malfunction.

HINT:

The steering lock ECU (steering lock actuator assembly) is not connected to the CAN communication system. However, the steering lock ECU (steering lock actuator assembly) is connected to the certification ECU (smart key ECU assembly) via LIN communication and communicates with other components via CAN communication through the certification ECU (smart key ECU assembly).


DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2788 IG2 Signal Malfunction Mismatch between the steering lock ECU (steering lock actuator assembly) IG2 input from the LIN communication system and from the direct line (1-trip detection logic (Only output while a malfunction is present and the engine switch is on (IG).)).
·

IG2 fuse

·

Steering lock ECU (Steering lock actuator assembly)

·

Harness or connector


DTC Output Confirmation Operation: No confirmation operation is necessary (monitoring is continuous).

Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
The steering cannot be locked or unlocked. For this reason, the engine cannot be started. -

Related Data List and Active Test Items
DTC No. Data List Item Active Test Item
B2788 - -

WIRING DIAGRAM

C270713
0.948,0.646 1.406,0.844 0.458,0.198 10 false LIN 0.229,3.042 0.688,3.24 0.458,0.198 10 false F13 0.229,3.188 2.031,3.698 1.802,0.51 10 false Certification ECU (Smart Key ECU Assembly) 1.26,0.469 1.573,0.667 0.313,0.198 10 false 6 5.146,0.479 5.458,0.677 0.313,0.198 10 false 5 5.146,1.333 5.458,1.531 0.313,0.198 10 false 6 5.146,2.094 5.458,2.292 0.313,0.198 10 false 1 1.802,1.417 2.99,1.708 1.188,0.292 10 false from IG2 Relay 4.042,1.604 4.99,1.969 0.948,0.365 10 false IG2 3.906,1.313 4.219,1.51 0.313,0.198 10 false 1 4.313,1.313 4.625,1.51 0.313,0.198 10 false 2 4.771,3.146 6.875,3.458 2.104,0.313 10 false Steering Lock ECU (Steering Lock Actuator Assembly) 4.781,2.979 5.24,3.177 0.458,0.198 10 false F54 5.354,2.24 5.813,2.438 0.458,0.198 10 false GND 5.375,1.458 5.833,1.656 0.458,0.198 10 false IG2 5.385,0.667 5.844,0.865 0.458,0.198 10 false LIN 2.771,3.354 4.438,3.604 1.667,0.25 10 false LIN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry & Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The steering lock system uses LIN communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After performing repairs, confirm that no DTCs are output again.

Click hereSteering>STEERING COLUMN>STEERING LOCK SYSTEM>DTC CHECK / CLEAR

·

When replacing the steering lock ECU (steering lock actuator assembly), registration must be performed (refer to Service Bulletin).



PROCEDURE

1.INSPECT STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY) (POWER SOURCE MODE SIGNAL)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the F54 steering lock ECU (steering lock actuator assembly) connector.


c.
C157850
0.344,0.917 0.74,1.229 0.396,0.313 1.281,2.417 1.031,1.729 false 0.375,0.302 0.823,0.604 0.448,0.302 10 false *a 0.427,0.969 0.844,1.333 0.417,0.365 10 false F54 0.823,1.563 1.177,1.75 0.354,0.188 10 false GND
*a Front view of wire harness connector
(to Steering Lock ECU (Steering Lock Actuator Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F54-1 (GND) - Body ground Always Below 1 Ω



d.

Reconnect the F54 steering lock ECU (steering lock actuator assembly) connector.


e.
C157849
0.292,0.885 0.74,1.177 0.448,0.292 2.281,1.958 2.813,2.823 false 1.333,1.969 0.833,2.823 false 0.375,0.271 0.667,0.521 0.292,0.25 10 false *a 0.396,0.927 0.771,1.177 0.375,0.25 10 false F54 0.698,2.854 1.104,3.063 0.406,0.208 10 false IG2 2.646,2.854 3.073,3.063 0.427,0.208 10 false GND
*a Component with harness connected
(Steering Lock ECU (Steering Lock Actuator Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F54-6 (IG2) - F54-1 (GND) Engine switch on (IG) 11 to 14 V
F54-6 (IG2) - F54-1 (GND) Engine switch off Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR