Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for Radio and Display Type) › 2013.12–2015.11
RM3160E _56 Audio / Visual / Telematics _019701 NAVIGATION / MULTI INFO DISPLAY _0101135 NAVIGATION SYSTEM(for Radio and Display Type) D

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Radio and Display Type)  DTC CHECK / CLEAR  


CHECK DTC (CHECK USING GTS)


a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Navigation System / Trouble Codes.

Body Electrical > Navigation System > Trouble Codes
50001 212

e.

Check for DTCs, and then write them down.


f.

Check the details of the DTC(s).

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Radio and Display Type)>DIAGNOSTIC TROUBLE CODE CHART

NOTICE:

The navigation system outputs DTCs for the following system. When DTCs other than those in Diagnostic Trouble Code Chart for the navigation system are output, refer to Diagnostic Trouble Code Chart for the relevant system.

System Proceed to
Parking Assist Monitor System (Click here)




CLEAR DTC (CLEAR USING GTS)


a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Navigation System / Trouble Codes.

Body Electrical > Navigation System > Clear DTCs
50002 212

e.

Clear the DTCs.



START DIAGNOSTIC MODE


HINT:
·

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

·

Start diagnostic mode at least 15 seconds after turning the engine switch on (IG). Otherwise, some items cannot be checked.

·

If the system cannot enter diagnostic mode, inspect all AVC-LAN communication components and repair or replace the malfunctioning parts (for 12 Speakers).

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Radio and Display Type)>AVC-LAN Circuit



a.

Turn the engine switch on (IG).


b.

While pressing and holding the "CAR" switch, operate the light control switch: Off → Tail → Off → Tail → Off → Tail → Off.


c.

Diagnostic mode starts and the "Service Menu" screen will be displayed. Service inspection starts automatically and the result will be displayed.



FAILURE DIAGNOSIS


a.
E268461

The "Failure Diagnosis" screen will be displayed by selecting "Failure Diagnosis" on the "Service Menu" screen.



SYSTEM CHECK


a.
E287165

The "System Check Mode" screen will be displayed by selecting "System Check" on the "Failure Diagnosis" screen.



CHECK DTC (CHECK USING SYSTEM CHECK MODE SCREEN)


a.
E287166N01
0.271,0.635 0.51,0.635 false 2.875,0.927 3.115,0.927 false 2.896,1.51 3.135,1.51 false 1.125,1.802 1.125,0.958 false 2.042,1.823 2.042,1.594 false 0.104,0.542 0.417,0.74 0.313,0.198 10 false *a 1.052,1.833 1.365,2.031 0.313,0.198 10 false *b 1.99,1.833 2.302,2.031 0.313,0.198 10 false *c 3.177,1.427 3.417,1.635 0.24,0.208 10 false *d 3.146,0.813 3.385,1.021 0.24,0.208 10 false *e

System check mode screen description

Screen Description
Display Content
*a: Device name list No. 1
·

Device Name List No. 1 displays some of the devices that make up the navigation system.

·

The names of the components from Device Name List No. 1 are shown in the following table.


*b: Check result Result codes for all devices are displayed.
*c: Memory clear
·

Present and history DTCs and registered connected device names are cleared.

·

Select "Memory CLR" for 3 seconds.


*d: Recheck
·

A system check will be performed again after the memory is cleared.

·

"Recheck" will dim during a system check.


*e: Device name list No. 2
·

Device Name List No. 2 displays some of the devices that make up the navigation system.

·

The names of the components from Device Name List No. 2 are shown in the following table.



*a: Device Name List No. 1 Description
Name Component Connection Method

*1: for 12 Speakers

DA Radio and display receiver assembly -
DSP-AMP*1 Stereo component amplifier assembly AVC-LAN communication line
NAVI BOX Navigation ECU LVDS communication line

*b: Check Result Description
Result Meaning Action
OK The device does not respond with a DTC. -
DETAIL The device responds with a DTC. Read the DTC on "Unit Check Mode" screen.
NCON The device was previously present, but does not respond in diagnostic mode.
·

Check the power supply circuit of the device.

·

Check the communication line of the device.


NRES The device responds in diagnostic mode, but gives no DTC information.

HINT:

When "NCON" is displayed for all devices connected through the AVC-LAN, or when all device names are not displayed, check if there is a short circuit in the AVC-LAN or devices connected to the AVC-LAN. Repair or replace parts as necessary (for 12 Speakers).

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Radio and Display Type)>AVC-LAN Circuit


*e: Device Name List No. 2 Description
Name Component Connection Method
AUX/VTR No. 1 stereo jack adapter assembly Vehicle wire harness
CAA Television camera assembly Vehicle wire harness


b.
E268464N01
0.865,1.854 0.865,1.115 false 0.406,0.688 0.667,0.688 false 2.906,1.677 3.031,1.677 false 1.448,0.427 1.51,0.25 1.51,0.25 1.635,0.25 true 1.271,0.625 1.167,0.25 1.167,0.25 1.031,0.25 true 1.646,0.156 1.896,0.385 0.25,0.229 10 false *a 0.885,0.156 1.135,0.385 0.25,0.229 10 false *b 0.26,0.583 0.51,0.813 0.25,0.229 10 false *c 0.771,1.865 1.021,2.094 0.25,0.229 10 false *d 3.031,1.583 3.281,1.813 0.25,0.229 10 false *e

Unit check mode screen description

Screen Description
Display Content
*a: Device name Target device
*b: History DTC Diagnostic memory results and stored DTCs are displayed.
*c: Current DTC DTCs output in the service check are displayed.
*d: DTC DTC (Diagnostic Trouble Code)
*e: Diagnosis clear switch Selecting "Code CLR" for 3 seconds clears the diagnostic memory data of the target device (both diagnostic system check result and the displayed data are cleared).

HINT:
·

This screen is updated once per second.

·

A maximum of 6 DTCs can be displayed for history and present DTCs.




c.
E287167

E287168

Read the system check result.

i.

If the check result is "DETAIL", select the displayed check result to view the results on the "Unit Check Mode" screen and record them.

NOTICE:

A maximum of 6 DTCs can be displayed for history and present DTCs on the "Unit Check Mode" screen. Therefore, when 6 DTCs are displayed, troubleshoot those DTCs first and then check the "Unit Check Mode" screen again to see if any other DTCs are displayed.


HINT:
·

When all results are "OK", no DTCs are present.

·

When proceeding to view the results of another device, select "Back" to return to the "System Check Mode" screen. Repeat the above step to view the results of other devices.




ii.

Check the details of the DTC(s).

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Radio and Display Type)>DIAGNOSTIC TROUBLE CODE CHART

NOTICE:

The navigation system outputs DTCs for the following system. When DTCs other than those in Diagnostic Trouble Code Chart for the navigation system are output, refer to Diagnostic Trouble Code Chart for the relevant system.

System Proceed to
Parking Assist Monitor System (Click here)





DTC CLEAR/RECHECK (CLEAR USING SYSTEM CHECK MODE SCREEN)


a.
E287169

Clear DTCs

i.

Select "Memory CLR" for 3 seconds.


ii.

Confirm that the check results are cleared.

HINT:
·

To clear DTCs for a specific device, clear the DTCs using the "Unit Check Mode" screen.

·

When clearing DTCs using the "Unit Check Mode" screen, select "Code CLR" for 3 seconds.





b.
E287170

Recheck

i.

Select "Recheck".


ii.
E287171

Confirm that all diagnostic codes are "OK" when the check results are displayed. If a result other than "OK" is displayed, perform troubleshooting again.

HINT:

When the DTCs are cleared using the "Unit Check Mode" screen, select "Back" to return to the "System Check Mode" screen and perform this operation.





FINISH DIAGNOSTIC MODE


a.

Turn the engine switch off.