Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for Radio and Display Type)
RM3160E _56 Audio / Visual / Telematics _019701 NAVIGATION / MULTI INFO DISPLAY _0101135 NAVIGATION SYSTEM(for Radio and Display Type) C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Radio and Display Type)  B1532  LVDS Signal Malfunction (from Extension Module)  


DESCRIPTION

The navigation ECU and the radio and display receiver assembly are connected by the LVDS communication line.

This DTC is stored when an LVDS communication error occurs between the navigation ECU and the radio and display receiver assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1532 LVDS Signal Malfunction (from Extension Module) When one of the conditions below is met:
·

Video signal (digital) is lost.

·

Navigation ECU is/was not connected while the engine switch is/was on (ACC) or on (IG).

·

Communication between the radio and display receiver assembly and the navigation ECU is/was not possible when the engine is/was started.


·

Navigation ECU power source circuit

·

LVDS circuit between radio and display receiver assembly and navigation ECU

·

Navigation ECU

·

Radio and display receiver assembly

·

No. 1 navigation wire



HINT:

Even if no malfunction is present, this DTC may be stored depending on the battery condition or engine start voltage.


WIRING DIAGRAM

E287116E03
1.083,3.271 2.917,3.438 1.833,0.167 10 false : LVDS Communication Line 0.667,2.344 2.385,2.677 1.719,0.333 10 false Radio and Display Receiver Assembly 3.531,2.333 3.781,2.5 0.25,0.167 10 false *1 3.333,3.271 5.198,3.594 1.865,0.323 10 false *1: No. 1 Navigation Wire 5.25,2.344 6.802,2.677 1.552,0.333 10 false Navigation ECU 4.844,1.875 5.083,2.042 0.24,0.167 10 false n2 4.844,1.479 5.083,1.646 0.24,0.167 10 false n4 4.833,1.083 5.073,1.25 0.24,0.167 10 false n4 4.833,0.688 5.073,0.854 0.24,0.167 10 false n4 5.167,0.688 5.5,0.854 0.333,0.167 10 false +B 5.167,1.083 5.583,1.25 0.417,0.167 10 false ACC 5.167,1.479 5.583,1.646 0.417,0.167 10 false GND 5.156,1.896 5.667,2.063 0.51,0.167 10 false GVIF 1.729,1.875 2.208,2.042 0.479,0.167 10 false GVIF 1.677,1.479 2.094,1.646 0.417,0.167 10 false GND2 1.688,1.094 2.104,1.26 0.417,0.167 10 false ACC2 1.781,0.688 2.115,0.854 0.333,0.167 10 false +B2 2.219,0.688 2.49,0.854 0.271,0.167 10 false n3 2.219,1.083 2.49,1.25 0.271,0.167 10 false n3 2.219,1.469 2.49,1.635 0.271,0.167 10 false n3 2.26,1.688 2.417,1.854 0.156,0.167 10 false 1 2.229,1.875 2.5,2.042 0.271,0.167 10 false n1 2.26,1.292 2.417,1.458 0.156,0.167 10 false 8 2.26,0.896 2.417,1.063 0.156,0.167 10 false 3 2.26,0.5 2.417,0.667 0.156,0.167 10 false 4 4.875,0.49 5.031,0.656 0.156,0.167 10 false 1 4.885,0.896 5.042,1.063 0.156,0.167 10 false 3 4.885,1.292 5.042,1.458 0.156,0.167 10 false 2 4.875,1.688 5.031,1.854 0.156,0.167 10 false 1

PROCEDURE

1.CHECK NO. 1 NAVIGATION WIRE (NAVIGATION ECU POWER SOURCE)
a.

Disconnect the n4 navigation ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
n4-2 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
n4-1 (+B) - n4-2 (GND) Always 11 to 14 V
n4-3 (ACC) - n4-2 (GND) Engine switch on (ACC) 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.REPLACE NO. 1 NAVIGATION WIRE

NG

4.CHECK NO. 1 NAVIGATION WIRE
2.REPLACE NO. 1 NAVIGATION WIRE
a.

Replace the No. 1 navigation wire with a new or known good one.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION ECU>REMOVAL


b.

Clear the DTCs.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Radio and Display Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Clear DTCs
50002 212

c.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END

NG

3.REPLACE NAVIGATION ECU
3.REPLACE NAVIGATION ECU
a.

Replace the navigation ECU with a new or known good one.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION ECU>REMOVAL


b.

Clear the DTCs.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Radio and Display Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Clear DTCs
50002 212

c.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

4.CHECK NO. 1 NAVIGATION WIRE
a.

Disconnect the n3 radio and display receiver assembly connector.


b.

Disconnect the n4 navigation ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
n3-4 (+B2) - n4-1 (+B) Always Below 1 Ω
n3-3 (ACC2) - n4-3 (ACC) Always Below 1 Ω
n3-8 (GND2) - n4-2 (GND) Always Below 1 Ω
n3-4 (+B2) - Body ground Always 10 kΩ or higher
n3-3 (ACC2) - Body ground Always 10 kΩ or higher
n3-8 (GND2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG