Home › Engine / Hybrid System › 1AR-FE FUEL › FUEL TANK
RM3160E _51 Engine / Hybrid System _019673 1AR-FE FUEL _0101270 FUEL TANK A

1AR-FE FUEL  FUEL TANK  INSTALLATION  


PROCEDURE

Hide 1.INSTALL TANK SUCTION TUBE SUPPORT

a.
A314698C01
1.073,0.354 1.51,0.354 false 2.229,0.323 2.531,0.323 false 0.646,2.76 0.865,2.76 false 1.635,2.167 1.906,2.167 false 0.875,0.25 1.188,0.406 0.313,0.156 10 false *a 0.438,2.667 0.625,2.833 0.188,0.167 10 true *b 2.573,0.24 2.885,0.396 0.313,0.156 10 false *a 1.948,2.083 2.115,2.24 0.167,0.156 10 true *b
*a Protrusion
*b Notch


Install a new tank suction tube support to the fuel tank assembly.

HINT:

Align the protrusion of the tank suction tube support with the notch of the fuel tank assembly.



Hide 77608C 2.INSTALL FUEL TANK CUSHION SET

a.

Install the 2 fuel tank cushion sets and 2 No. 5 fuel tank cushions to the fuel tank assembly.


Hide 77213B 3.INSTALL FUEL TANK TO FILLER PIPE HOSE

a.

Install the fuel tank to filler pipe hose to the fuel tank assembly and tighten the clamp to secure it.


Hide 4.INSTALL FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.

Engage the 3 claws to install the fuel tank main tube sub-assembly to the fuel tank assembly.


Hide 77113B 5.INSTALL FUEL TANK SIDE PLATE

a.

Install the fuel tank side plate to the fuel tank assembly with the fuel tank band pin and fuel tank cushion.


Hide 77100 6.INSTALL FUEL TANK ASSEMBLY

a.

Set the fuel tank assembly on an engine lifter.

HINT:

Using height adjustment attachments and plate lift attachments, place the fuel tank assembly horizontally.



b.

Using the engine lifter, slowly raise the fuel tank assembly, and then install the fuel tank assembly with the No. 1 fuel tank band sub-assembly LH and No. 1 fuel tank band sub-assembly RH with the 4 bolts.

NOTICE:
·

Do not drop the fuel tank assembly.

·

When installing the fuel tank assembly, tilt it slightly to prevent it from interfering with the other surrounding parts.



Torque:
39.2 N*m (400 kgf*cm, 29 ft.*lbf)


c.

Install the rear fuel tank bracket LH with the bolt and nut.

Torque:
Bolt : 39.2 N*m (400 kgf*cm, 29 ft.*lbf)
Nut : 19.6 N*m (200 kgf*cm, 14 ft.*lbf)


d.

Install the nut.

Torque:
19.6 N*m (200 kgf*cm, 14 ft.*lbf)


e.
A314699C01
1.271,0.5 1.844,0.5 false 0.667,1.188 1.24,1.188 false 0.75,2.385 1.063,2.542 0.313,0.156 10 false *a 2.198,2.615 2.51,2.771 0.313,0.156 10 false *b 0.49,1.104 0.667,1.26 0.177,0.156 10 true *1 1.052,0.406 1.25,0.583 0.198,0.177 10 true *2
*1 Fuel Tank To Filler Pipe Hose
*2 Fuel Tank To Filler Pipe Sub-assembly
*a Upper
*b 120°


Connect the fuel tank to filler pipe hose to the fuel tank to filler pipe sub-assembly and tighten the clamp to secure it.

HINT:

Make sure the clamp bolt is within the area shown in the illustration.



Hide 7.CONNECT FUEL TANK BREATHER TUBE

a.
A314700C01
1.01,2.271 1.323,2.427 0.313,0.156 10 false *a 2.104,2.542 2.417,2.698 0.313,0.156 10 false *b
*a Upper
*b 120°


Connect the fuel tank breather tube to the fuel pipe and tighten the clamp to secure it.

HINT:

Make sure the clamp bolt is within the area shown in the illustration.



Hide 77404 8.CONNECT FUEL TANK VENT HOSE SUB-ASSEMBLY

a.
A315524C01
2.24,0.469 2.375,0.469 2.375,0.469 2.448,0.719 false 2.063,0.365 2.375,0.521 0.313,0.156 10 false *a
*a Retainer
V100135

Push
V100136

Push In


Push the fuel tank vent hose sub-assembly onto the canister (charcoal canister assembly) and push in the retainer to engage the lock claws.

NOTICE:
·

Check that there are no scratches or foreign matter around the connecting parts of the fuel tank vent hose sub-assembly and pipe (canister (charcoal canister assembly)) before performing this work.

·

After connecting the fuel tank vent hose sub-assembly, check that the fuel tank vent hose sub-assembly is securely connected by pulling on the tube connector.




Hide 77209F 9.CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.
A314701C01
0.427,2.365 0.531,2.365 0.531,2.365 0.615,2.156 false 0.49,2.875 0.625,2.875 0.625,2.875 0.708,3.313 false 0.865,3.219 1.042,2.833 1.042,2.833 1.177,2.833 false 1.323,4.219 1.323,3.729 false 1.156,3.719 1.156,4.219 1.156,4.219 1.604,4.219 false 0.385,4.083 0.385,3.938 0.385,3.938 0.635,3.667 false 0.26,2.271 0.573,2.427 0.313,0.156 10 false *a 1.635,4.125 1.948,4.281 0.313,0.156 10 false *b 1.219,2.74 1.531,2.896 0.313,0.156 10 false *c 0.323,4.104 0.635,4.26 0.313,0.156 10 false *d 0.302,2.781 0.615,2.938 0.313,0.156 10 false *a
*a Retainer
*b O-ring
*c Fuel Tube Connector
*d Fuel Pipe
V100135

Push
V100136

Push In


Connect the fuel tank main tube sub-assembly.

NOTICE:

Check if there is any damage or foreign matter on the connecting parts of the fuel lines.


i.

Align the fuel tube connector with the fuel pipe, and push them together until the fuel tube connector makes a "click" sound. If it is difficult to push the fuel pipe into the fuel tube connector, apply a small amount of clean engine oil to the tip of the fuel pipe and reinsert it.


ii.

Connect the fuel lines and push in the retainer. Check that the fuel pipe and fuel tube connector are securely connected by pulling on them.



Hide 77606 10.INSTALL NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY

a.

Install the No. 1 fuel tank protector sub-assembly with the 7 nuts and 4 new clips.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 77765 11.INSTALL CHARCOAL CANISTER PROTECTOR

Hide 58167A 12.INSTALL FRONT CENTER FLOOR COVER

a.

Engage the 4 clips to install the front center floor cover.


b.

Install the 2 screws and nut.


Hide 51206A 13.INSTALL REAR SUSPENSION MEMBER SUB-ASSEMBLY

Hide 77020A 14.INSTALL FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY