Home › Engine / Hybrid System › 1AR-FE FUEL › FUEL PUMP
RM3160E _51 Engine / Hybrid System _019673 1AR-FE FUEL _0108299 FUEL PUMP A

1AR-FE FUEL  FUEL PUMP  INSTALLATION  


PROCEDURE

Hide 77020A 1.INSTALL FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

a.

Install a new fuel suction tube set gasket to the fuel tank assembly.


b.
A313780C01
1.594,0.177 1.688,0.177 1.688,0.177 1.74,0.583 false 0.292,1.25 0.417,1.25 0.417,1.25 0.417,0.76 false 1.104,2.781 1.781,2.781 false 1.427,0.083 1.74,0.24 0.313,0.156 10 false *a 0.917,2.688 1.083,2.844 0.167,0.156 10 true *b 0.125,1.156 0.438,1.313 0.313,0.156 10 false *a
*a Protrusion
*b Notch


Set the fuel suction tube with pump and gauge assembly to the fuel tank assembly.

NOTICE:

Make sure that the fuel sender gauge arm does not bend.


HINT:

Align the protrusion of the fuel suction tube with pump and gauge assembly with the notch of the tank suction tube support.



Hide 77144 2.INSTALL FUEL PUMP GAUGE RETAINER

a.
A337341C01
1.031,0.188 1.385,0.188 true 1.573,0.417 1.854,0.854 1.854,0.854 1.99,0.854 true 0.854,0.083 1.042,0.271 0.188,0.188 10 true *a 2.063,0.781 2.375,0.938 0.313,0.156 10 false *b
*a "S" Mark
*b Triangle Mark


Align the triangle mark on new fuel pump gauge retainer with the "S" mark on the fuel tank assembly while pushing down the fuel suction tube with pump and gauge assembly, attach the fuel pump gauge retainer.


b.

Install SST (fuel pump retainer tool assy) to the fuel pump gauge retainer.

i.

Insert 2 SST (claw) between the service hole and fuel pump gauge retainer, and adjust the position so that the protrusions of the fuel pump gauge retainer are aligned with the grooves of SST (claw) as shown in the illustration.

A329813C01
2.594,1.448 3.104,1.448 false 3.854,0.542 4.167,0.542 false 1.698,2.552 1.885,2.552 1.885,2.552 2.24,2.99 false 2.396,2.865 2.438,3.5 2.438,3.5 3.073,3.125 true 2.427,2.802 3.156,2.479 3.156,2.479 3.115,3.073 true 4.698,2.802 5.49,2.427 5.49,2.427 5.438,2.875 true 4.698,2.865 4.958,3.5 4.958,3.5 5.406,2.948 true 4.219,0.458 4.531,0.615 0.313,0.156 10 true *a 1.521,2.469 1.833,2.625 0.313,0.156 10 false *b 1.156,2.281 1.469,2.438 0.313,0.156 10 false *e 3.823,2.281 4.135,2.438 0.313,0.156 10 false *f 2.417,1.354 2.729,1.51 0.313,0.156 10 true *a 2.333,3.51 2.646,3.667 0.313,0.156 10 false *c 4.865,3.531 5.177,3.688 0.313,0.156 10 false *c 5.531,2.292 5.844,2.448 0.313,0.156 10 false *d 3.198,2.333 3.51,2.49 0.313,0.156 10 false *d
*a SST (Claw) *b Triangle Mark
*c Protrusion of Fuel Pump Gauge Retainer *d Groove of SST (Claw)
*e Correct *f Incorrect


SST
09808-14040  (09882-14040)

NOTICE:

Ensure that SST (claw) does not cover the triangle mark of the fuel pump gauge retainer.



ii.
A329816C01
2.083,0.167 2.531,0.167 false 2.021,0.719 2.469,0.719 false 0.677,1.969 1.26,1.969 false 0.51,1.875 0.823,2.031 0.313,0.156 10 false *a 2.563,0.083 2.875,0.24 0.313,0.156 10 false *b 2.5,0.625 2.813,0.781 0.313,0.156 10 true *a 1.042,0.76 1.24,0.927 0.198,0.167 10 true *c 1.427,0.021 1.625,0.188 0.198,0.167 10 false *c
*a SST (Claw)
*b SST (Plate)
*c SST (Bolt and Washer Set)


While ensuring that SST (plate) is centered, install SST (plate) to 2 SST (claw) with the 2 SST (bolt and washer set).

SST
09808-14040  (09881-14040, 09883-14040)



c.
A337340C01
1.563,1.104 1.958,1.948 1.958,1.948 2.104,1.948 true 2.521,3.323 2.698,3.021 2.698,3.021 2.813,3.021 true 2.76,4.229 2.625,4.229 2.625,4.229 2.208,3.771 true 1.771,4.427 1.771,4.292 1.771,4.292 1.938,4.167 false 2.167,1.875 2.479,2.031 0.313,0.156 10 false *a 2.833,4.146 3.146,4.302 0.313,0.156 10 false *b 1.688,4.438 1.906,4.594 0.219,0.156 10 true *c 2.865,2.938 3.177,3.094 0.313,0.156 10 false *d
*a SST (Fuel Pump Retainer Tool Assy)
*b Triangle Mark
*c "535" Mark
*d "475" Mark


While lightly pushing down on SST (fuel pump retainer tool assy), tighten the fuel pump gauge retainer by 1 and a half turns so that the triangle mark on the fuel pump gauge retainer is positioned between the "475" and "535" marks on the fuel tank assembly.

NOTICE:
·

Do not use any tools other than specified in this operation as this may result in damage to the fuel pump gauge retainer or fuel tank assembly.

·

Do not push down on SST (fuel pump retainer tool assy) excessively as this may make the fuel pump gauge retainer hard to rotate, and may damage components.

·

Make sure to turn the breaker bar horizontally. If it is turned at an angle, SST (fuel pump retainer tool assy) may come off.

·

Do not spin SST (fuel pump retainer tool assy) too fast or use an impact wrench as this may damage components.

·

If SST (fuel pump retainer tool assy) comes off of the fuel pump gauge retainer, loosen the SST (bolt and washer set) and reinstall SST (fuel pump retainer tool assy).



HINT:

While pushing down SST (fuel pump retainer tool assy), turn the fuel pump gauge retainer clockwise to tighten. Make sure that the detent of the tank suction tube support does not move out of the groove of the fuel tank assembly.



Hide 77209F 3.CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.
A314719C01
1.948,1.177 2.24,1.427 2.24,1.427 2.385,1.427 false 1.031,2.01 1.719,2.01 false 2.26,1.719 2.635,1.719 false 2.25,2.167 2.958,2.167 false 2.24,2.302 2.74,2.302 2.74,2.302 2.74,2.167 false 2.552,3.76 2.802,3.354 2.802,3.354 3,3.354 false 0.615,4.24 0.74,4.24 0.74,4.24 1.031,3.823 false 0.375,3.698 0.75,3.698 false 1.896,3.792 2.271,3.792 false 0.844,1.938 1.156,2.094 0.313,0.156 10 false *1 2.677,1.635 2.99,1.792 0.313,0.156 10 false *a 3.01,2.094 3.323,2.25 0.313,0.156 10 false *b 0.438,4.146 0.75,4.302 0.313,0.156 10 false *c 0.302,3.188 0.615,3.344 0.313,0.156 10 false *d 2.031,3.177 2.344,3.333 0.313,0.156 10 false *e 2.458,1.354 2.771,1.51 0.313,0.156 10 true *1 3.052,3.26 3.365,3.417 0.313,0.156 10 false *c 0.198,3.625 0.51,3.781 0.313,0.156 10 false *1 1.719,3.719 2.031,3.875 0.313,0.156 10 false *1
*1 Tube Joint Clip
*a Fuel Tube Joint
*b O-ring
*c Collar
*d Correct
*e Incorrect


Push the fuel tube joint onto the plug of the fuel suction plate sub-assembly, then install the tube joint clip.

NOTICE:
·

Check that there are no scratches or foreign matter around the connecting parts of the fuel tube joint and plug before performing this work.

·

Check that the fuel tube joint is securely inserted to the end.

·

Check that the tube joint clip is on the collar of the fuel tube joint.

·

After installing the tube joint clip, check that the fuel tank main tube sub-assembly is securely connected by pulling on it.




Hide 4. CHECK AIRTIGHTNESS

a.
A309793

After installing the fuel suction tube with pump and gauge assembly, check for fuel leaks by first applying soapy water to the area where the fuel suction plate sub-assembly and fuel pump gauge retainer contact, and then blow forcefully into the fuel inlet area through a flexible pouring spout or similar tube.


b.

Blow forcefully until the reverse flow prevention valve inside the fuel inlet activates.

NOTICE:

Be careful not to inhale any fuel vapor.


HINT:

There should be a faintly audible sound when the reverse flow prevention valve operates.



c.
A313788C01
2.135,1.021 2.458,0.729 2.458,0.729 2.615,0.729 true 2.677,0.646 2.906,0.813 0.229,0.167 10 true *a
*a Air Bubbles


If improper installation of the fuel suction tube with pump and gauge assembly, etc. has resulted in a condition where fuel will leak, air will leak out as shown in the illustration.

NOTICE:

If air leaks out, recheck the installation condition, and replace the used fuel pump gauge retainer and fuel suction tube set gasket with new ones. Also, make sure to fully wipe away the soapy water. (Any remaining soapy water can cause the fuel suction tube set gasket to slip and result in an improper seal.)



Hide 58325E 5.INSTALL REAR FLOOR SERVICE HOLE COVER

a.

Connect the fuel pump connector.


b.

Install the rear floor service hole cover with new butyl tape.


c.

Install the front floor carpet.


Hide 64740C 6.INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH

Hide 66311 7.INSTALL ROPE HOOK (for LH Side)

Hide 64725F 8.INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK (for LH Side)

Hide 64974 9.INSTALL DECK TRIM POCKET COVER (for LH Side)

Hide 73570 10.CONNECT REAR NO. 2 SEAT OUTER BELT ASSEMBLY LH

Hide 64735 11.INSTALL DECK TRIM SIDE SERVICE HOLE COVER

Hide 64715E 12.INSTALL NO. 2 DECK SIDE TRIM COVER

Hide 73370C 13.CONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH

Hide 64713F 14.INSTALL FRONT DECK SIDE TRIM COVER LH

Hide 64730B 15.INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH

Hide 66311 16.INSTALL ROPE HOOK (for RH Side)

Hide 64725F 17.INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK (for RH Side)

Hide 64974 18.INSTALL DECK TRIM POCKET COVER (for RH Side)

Hide 81240 19.INSTALL NO. 1 ROOM LIGHT ASSEMBLY

Hide 62627D 20.INSTALL SIDE TRIM COVER RH (w/o Rear Automatic Air Conditioning System)

Hide 88625Q 21.INSTALL COOLER (NO. 2 ROOM TEMP. SENSOR) THERMISTOR

Hide 73560 22.CONNECT REAR NO. 2 SEAT OUTER BELT ASSEMBLY RH

Hide 73297E 23.INSTALL DECK TRIM SIDE BELT HOLE COVER RH

Hide 64714H 24.INSTALL NO. 1 DECK SIDE TRIM COVER

Hide 73360C 25.CONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY RH

Hide 64712F 26.INSTALL FRONT DECK SIDE TRIM COVER RH

Hide 27.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

Hide 67918A 28.INSTALL REAR DOOR SCUFF PLATE LH

Hide 29.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH

Hide 67917A 30.INSTALL REAR DOOR SCUFF PLATE RH

Hide 31.INSTALL REAR NO. 2 SEAT ASSEMBLY

Hide 64910J 32.INSTALL TONNEAU COVER ASSEMBLY

Hide 58387B 33.INSTALL REAR FLOOR FINISH PLATE

Hide 64993 34.INSTALL REAR DECK FLOOR BOX

Hide 64742C 35.INSTALL DECK SIDE TRIM BOX LH

Hide 58409A 36.INSTALL NO. 3 DECK BOARD SUB-ASSEMBLY

Hide 58410B 37.INSTALL DECK BOARD ASSEMBLY

Hide 38.INSTALL REAR NO. 1 SEAT ASSEMBLY

Hide 39.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 41.PERFORM INITIALIZATION

a.

Perform "Inspection After Repair" after replacing the fuel pump.

Click hereEngine / Hybrid System>1AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION