This DTC is stored when a malfunction occurs in the speakers.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B15C3 | Speaker Output Short | A short is detected in the speaker output circuit. | ·
Harness or connector ·
Speaker ·
Radio and display receiver assembly*1 ·
Stereo component amplifier assembly*2 |
*1: for 6 Speakers
*2: for 12 Speakers
for 6 Speakers
for 12 Speakers
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| for 6 Speakers | A |
| for 12 Speakers | B |
A
B
Disconnect the F69 and F70 radio and display receiver assembly connectors.
Disconnect the G1 and G5 front No. 2 speaker assembly connectors.
Disconnect the J4 and K4 rear speaker assembly connectors.
Measure the resistance between the radio and display receiver assembly and body ground to check for a short circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F69-1 (FR+) - Body ground | Always | 10 kΩ or higher |
| F69-5 (FR-) - Body ground | Always | 10 kΩ or higher |
| F69-2 (FL+) - Body ground | Always | 10 kΩ or higher |
| F69-6 (FL-) - Body ground | Always | 10 kΩ or higher |
| F70-1 (RR+) - Body ground | Always | 10 kΩ or higher |
| F70-3 (RR-) - Body ground | Always | 10 kΩ or higher |
| F70-2 (RL+) - Body ground | Always | 10 kΩ or higher |
| F70-6 (RL-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H3 and I3 front No. 1 speaker assembly connectors.
Disconnect the G1 and G5 front No. 2 speaker assembly connectors.
Measure the resistance between each of the front No. 2 speaker assemblies and body ground to check for a short circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G1-3 (+) - Body ground | Always | 10 kΩ or higher |
| G1-1 (-) - Body ground | Always | 10 kΩ or higher |
| G5-3 (+) - Body ground | Always | 10 kΩ or higher |
| G5-1 (-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front No. 1 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL
| *a | Component without harness connected
(Front No. 1 Speaker Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | Always | 3.2 to 4.8 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front No. 2 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL
| *a | Component without harness connected
(Front No. 2 Speaker Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4 (+) - 2 (-) | Always | 10 kΩ or higher |
| 3 (+) - 4 (+) | Always | Below 1 Ω |
| 1 (-) - 2 (-) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the front No. 2 speaker assembly with a new or known good one.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL
Clear the DTCs.
Recheck for DTCs and check that no DTCs are output.
No DTCs are output.
Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.
When there is a possibility that either the right or left front No. 2 speaker assembly is defective, inspect by interchanging the right one with the left one.
Perform the above inspection on both the LH and RH side.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>REMOVAL
| *a | Component without harness connected
(Rear Speaker Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | Always | 3.2 to 4.8 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F75 stereo component amplifier assembly connector.
Disconnect the H3 and I3 front No. 1 speaker assembly connectors.
Disconnect the G3 front No. 3 speaker assembly connector.
Disconnect the J4 and K4 rear speaker assembly connectors.
Disconnect the X23 and X5 rear No. 3 speaker assembly connectors.
Disconnect the G2 and G6 front No. 2 speaker assembly connectors.
Disconnect the X26 rear No. 2 speaker assembly connector.
Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F75-15 (FR+) - Body ground | Always | 10 kΩ or higher |
| F75-30 (FR-) - Body ground | Always | 10 kΩ or higher |
| F75-11 (FL+) - Body ground | Always | 10 kΩ or higher |
| F75-26 (FL-) - Body ground | Always | 10 kΩ or higher |
| F75-10 (CTR+) - Body ground | Always | 10 kΩ or higher |
| F75-25 (CTR-) - Body ground | Always | 10 kΩ or higher |
| F75-12 (RR+) - Body ground | Always | 10 kΩ or higher |
| F75-27 (RR-) - Body ground | Always | 10 kΩ or higher |
| F75-4 (RL+) - Body ground | Always | 10 kΩ or higher |
| F75-19 (RL-) - Body ground | Always | 10 kΩ or higher |
| F75-9 (SR+) - Body ground | Always | 10 kΩ or higher |
| F75-24 (SR-) - Body ground | Always | 10 kΩ or higher |
| F75-5 (SL+) - Body ground | Always | 10 kΩ or higher |
| F75-20 (SL-) - Body ground | Always | 10 kΩ or higher |
| F75-14 (TWR+) - Body ground | Always | 10 kΩ or higher |
| F75-29 (TWR-) - Body ground | Always | 10 kΩ or higher |
| F75-13 (TWL+) - Body ground | Always | 10 kΩ or higher |
| F75-28 (TWL-) - Body ground | Always | 10 kΩ or higher |
| F75-8 (WF1+) - Body ground | Always | 10 kΩ or higher |
| F75-23 (WF1-) - Body ground | Always | 10 kΩ or higher |
| F75-7 (WF2+) - Body ground | Always | 10 kΩ or higher |
| F75-22 (WF2-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front No. 1 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL
| *a | Component without harness connected
(Front No. 1 Speaker Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | Always | 4.6 to 6.6 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front No. 3 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL
| *a | Component without harness connected
(Front No. 3 Speaker Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | Always | 6.8 to 10.2 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>REMOVAL
| *a | Component without harness connected
(Rear Speaker Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | Always | 3.2 to 5.2 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear No. 3 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>BACK DOOR SPEAKER>REMOVAL
| *a | Component without harness connected
(Rear No. 3 Speaker Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | Always | 6.8 to 10.2 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front No. 2 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL
| *A | for RH |
| *B | for LH |
| *a | Component without harness connected
(Front No. 2 Speaker Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4 (TWR+) - 3 (TWR-) | Always | 3.4 to 5.2 Ω |
| 4 (TWL+) - 3 (TWL-) | Always | 3.4 to 5.2 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear No. 2 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>BACK DOOR SPEAKER>REMOVAL
| *a | Component without harness connected
(Rear No. 2 Speaker Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (WF2-) - 2 (WF2+) | Always | 4.8 to 6.8 Ω |
| 3 (WF1-) - 4 (WF1+) | Always | 4.8 to 6.8 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG