Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM
RM3160E _59 Vehicle Exterior _019722 LIGHTING (EXT) _0103403 LIGHTING SYSTEM C

LIGHTING (EXT)  LIGHTING SYSTEM  B1244  Light Sensor Circuit Malfunction  


DESCRIPTION

The automatic light control sensor detects ambient light. The sensor creates an electrical signal based on the amount of light detected, and sends the signal to the main body ECU (multiplex network body ECU). The main body ECU (multiplex network body ECU) turns on or off the headlights and taillights according to the signal.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1244 Light Sensor Circuit Malfunction Either of the following conditions is met:
·

Malfunction in automatic light control sensor

·

Open or short in automatic light control sensor circuit


·

Automatic light control sensor

·

Harness or connector

·

Main body ECU (multiplex network body ECU)



WIRING DIAGRAM

E223761
4.792,2.781 6.427,3.198 1.635,0.417 10 false Main Body ECU (Multiplex Network Body ECU) 0.531,2.729 2.51,3.094 1.979,0.365 10 false Automatic Light Control Sensor 0.542,2.583 0.844,2.75 0.302,0.167 10 false G4 4.792,2.625 5.094,2.792 0.302,0.167 10 false F19 4.76,0.74 5.021,0.917 0.26,0.177 10 false 19 5.031,0.854 5.635,1.125 0.604,0.271 10 false CLTB 4.771,1.406 5.021,1.573 0.25,0.167 10 false 20 5.031,1.51 5.573,1.781 0.542,0.271 10 false CLTS 4.771,2.063 5.031,2.219 0.26,0.156 10 false 21 2.063,0.74 2.396,1.073 0.333,0.333 10 false 1 2.073,1.406 2.396,1.708 0.323,0.302 10 false 4 2.073,2.073 2.302,2.427 0.229,0.354 10 false 2 5.031,2.177 5.563,2.396 0.531,0.219 10 false CLTE 1.604,0.854 2.052,1.021 0.448,0.167 10 false CLTB 1.615,1.51 2.042,1.677 0.427,0.167 10 false CLTS 1.615,2.188 2.063,2.344 0.448,0.156 10 false CLTE

CAUTION / NOTICE / HINT

NOTICE:
·

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.*

*: w/ Smart Entry and Start System


·

As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

*: for LHD




PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Light Sensor Illuminance Light control sensor illuminance 0 to 8191 lx Value is output according to ambient light level -
Body Electrical > Main Body > Data List
Tester Display
Light Sensor Illuminance
50003 123 279
OK:

Normal condition listed above is displayed.



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - AUTOMATIC LIGHT CONTROL SENSOR)
2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - AUTOMATIC LIGHT CONTROL SENSOR)
a.

Disconnect the G4 automatic light control sensor connector.


b.

Disconnect the F19 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F19-21 (CLTE) - G4-2 (CLTE) Always Below 1 Ω
F19-20 (CLTS) - G4-4 (CLTS) Always Below 1 Ω
F19-19 (CLTB) - G4-1 (CLTB) Always Below 1 Ω
F19-21 (CLTE) - Body ground Always 10 kΩ or higher
F19-20 (CLTS) - Body ground Always 10 kΩ or higher
F19-19 (CLTB) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
a.
E173035
1.552,0.563 1.917,0.823 0.365,0.26 1.354,2.708 2.344,2 false 2.396,2.708 2.563,2 false 0.146,0.135 0.604,0.438 0.458,0.302 10 false *a 1.146,2.76 1.625,2.979 0.479,0.219 10 false CLTE 2.208,2.75 2.979,3.063 0.771,0.313 10 false CLTB 1.625,0.615 2.083,0.813 0.458,0.198 10 false F19
*a Component with harness connected
(Main Body ECU (Multiplex Network Body ECU))


Reconnect the F19 main body ECU (multiplex network body ECU) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F19-19 (CLTB) - F19-21 (CLTE) Ignition switch off, dimmer switch off, 2 minutes after all doors closed Below 1 V
Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.INSPECT AUTOMATIC LIGHT CONTROL SENSOR

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

4.INSPECT AUTOMATIC LIGHT CONTROL SENSOR
a.
E259758
1.531,0.271 1.927,0.49 0.396,0.219 1.833,1.177 2.385,0.885 false 1.458,1.167 0.896,0.896 false 0.188,0.135 0.438,0.313 0.25,0.177 10 false *a 1.635,0.292 2.229,0.74 0.594,0.448 10 false G4 0.542,0.771 0.958,0.948 0.417,0.177 10 false CLTS 2.438,0.792 2.833,0.958 0.396,0.167 10 false CLTE
*a Component with harness connected
(Automatic Light Control Sensor)


Reconnect the G4 automatic light control sensor connector.


b.

Connect an oscilloscope to the automatic light control sensor connector.


c.
E276298N01
2.844,1.646 3.219,1.813 0.375,0.167 10 false GND

Check the waveform.

OK:
Tester Connection Tool Setting Condition Specified Condition
G4-2 (CLTE) - G4-4 (CLTS) 2 V/DIV., 10 ms./DIV. Ignition switch ON Correct waveform is as shown


HINT:

The communication waveform changes according to the surrounding brightness.



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE AUTOMATIC LIGHT CONTROL SENSOR