Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM
RM3160E _59 Vehicle Exterior _019722 LIGHTING (EXT) _0103403 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Parking Brake Switch Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) detects the condition of the parking brake switch assembly.

WIRING DIAGRAM

E289300E02
1.198,1.229 3.344,1.51 2.146,0.281 10 false Parking Brake Switch Assembly 1.188,1.073 1.813,1.469 0.625,0.396 10 false A58 3.885,1.083 5.885,1.688 2,0.604 10 false Instrument Panel Junction Block Assembly 5.396,1.927 7.021,2.573 1.625,0.646 10 false Main Body ECU (Multiplex Network Body ECU) 5.396,1.76 6.021,2.156 0.625,0.396 10 false MB 2.5,0.635 3.125,1.031 0.625,0.396 10 false + 2.698,0.635 3.323,1.031 0.625,0.396 10 false 1 3.938,0.542 4.563,0.938 0.625,0.396 10 false 28 3.938,0.75 4.563,1.146 0.625,0.396 10 false 4F 5.99,0.76 6.615,1.156 0.625,0.396 10 false PKB 5.729,0.635 6.354,1.031 0.625,0.396 10 false 12

CAUTION / NOTICE / HINT

NOTICE:
·

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.*

*: w/ Smart Entry and Start System


·

As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

*: for LHD




PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Parking Brake SW Parking brake switch signal ON or OFF ON: Parking brake switch on
OFF: Parking brake switch off
-
Body Electrical > Main Body > Data List
Tester Display
Parking Brake SW
50003 123 12
OK:

Normal conditions listed above are displayed.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT PARKING BRAKE SWITCH ASSEMBLY
2.INSPECT PARKING BRAKE SWITCH ASSEMBLY
a.

Remove the parking brake switch assembly.

for LHD: Click hereBrake>PARKING BRAKE>PARKING BRAKE SWITCH(for LHD)>REMOVAL

for RHD: Click hereBrake>PARKING BRAKE>PARKING BRAKE SWITCH(for RHD)>REMOVAL


b.

Inspect the parking brake switch assembly.

for LHD: Click hereBrake>PARKING BRAKE>PARKING BRAKE SWITCH(for LHD)>INSPECTION

for RHD: Click hereBrake>PARKING BRAKE>PARKING BRAKE SWITCH(for RHD)>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (PARKING BRAKE SWITCH ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPLACE PARKING BRAKE SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (PARKING BRAKE SWITCH ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 4F instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A58-1 (+) - 4F-28 Always Below 1 Ω
A58-1 (+) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

E259752C08
1.229,0.302 1.563,0.531 0.333,0.229 4.594,0.458 4.927,0.688 0.333,0.229 4.417,1.531 4.24,1.115 false 0.125,0.083 0.438,0.281 0.313,0.198 10 false *a 1.323,0.333 1.635,0.531 0.313,0.198 10 false 4F 4.677,0.5 4.99,0.698 0.313,0.198 10 false MB 4.281,1.542 4.646,1.75 0.365,0.208 10 false PKB
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
4F-28 - MB-12 (PKB) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY