Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM › 2013.12–2016.11
RM3160E _58 Vehicle Interior _019707 LIGHTING (INT) _0103507 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  ACC Signal Circuit  


DESCRIPTION

This circuit detects the ignition switch ACC or off condition, and sends it to the main body ECU (multiplex network body ECU).

WIRING DIAGRAM

E287406
3.177,1.729 3.375,1.927 0.198,0.198 10 false 27 3.177,0.948 3.417,1.135 0.24,0.188 10 false 28 3.219,0.469 3.375,0.667 0.156,0.198 10 false 1 1.271,0.656 2.125,0.885 0.854,0.229 10 false from Battery 0.229,1.146 2.094,1.677 1.865,0.531 10 false from Certification ECU (Smart Key ECU Assembly)*1 or Ignition Switch Assembly*2 3.177,0.677 3.49,0.875 0.313,0.198 10 false 4K 5.521,2.823 5.844,3.021 0.323,0.198 10 false MB 5.99,0.583 6.188,0.792 0.198,0.208 10 false 30 3.177,1.146 3.438,1.333 0.26,0.188 10 false 4A 3.177,1.927 3.438,2.115 0.26,0.188 10 false 4A 6.24,0.656 6.698,0.854 0.458,0.198 10 false ACC 5.135,0.823 5.948,1.052 0.813,0.229 10 false ECU-ACC 4.427,1.417 4.885,1.615 0.458,0.198 10 false ACC 5.521,3.01 7.156,3.49 1.635,0.479 10 false Main Body ECU (Multiplex Network Body ECU) 3.469,2.448 6.208,2.688 2.74,0.24 10 false Instrument Panel Junction Block Assembly 0.354,2.917 2.906,3.177 2.552,0.26 10 false *1: w/ Smart Entry and Start System 0.354,3.281 3.188,3.573 2.833,0.292 10 false *2: w/o Smart Entry and Start System

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.*1

·

As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.*2

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION


*1: w/ Smart Entry and Start System

*2: for LHD



PROCEDURE

1.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
w/ Smart Entry and Start System A
w/o Smart Entry and Start System B



A

2.CHECK FOR DTC (SMART ENTRY AND START SYSTEM (for Start Function))

B

6.READ VALUE USING GTS
2.CHECK FOR DTC (SMART ENTRY AND START SYSTEM (for Start Function))
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Clear DTCs
50002 125

b.

Check for the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Trouble Codes
50001 125

Result:
Result Proceed to
Smart Entry and Start System (for Start Function) DTCs are not output A
Smart Entry and Start System (for Start Function) DTCs are output B



A

3.READ VALUE USING GTS

B

3.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ACC SW Ignition switch ACC signal ON or OFF ON: Ignition switch ACC
OFF: Ignition switch off
"ON" is also displayed for this item when the ignition switch is ON.
Body Electrical > Main Body > Data List
Tester Display
ACC SW
50003 123 31
OK:

Normal conditions listed above are displayed.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

4.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BATTERY AND BODY GROUND)
4.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BATTERY AND BODY GROUND)
a.

Disconnect the 4A and 4K instrument panel junction block assembly connectors.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
4K-1 - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4A-27 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

E288979C01
1.51,0.406 1.823,0.667 0.313,0.26 4.75,0.354 5.063,0.615 0.313,0.26 3.344,2.198 3.656,2.458 0.313,0.26 4.771,3.417 4.938,3.417 4.938,3.417 5.188,2.917 false 0.188,0.156 0.5,0.354 0.313,0.198 10 false *a 1.583,0.448 1.896,0.646 0.313,0.198 10 false 4K 4.823,0.406 5.135,0.604 0.313,0.198 10 false 4A 3.406,2.26 3.719,2.458 0.313,0.198 10 false MB 4.427,3.333 4.74,3.531 0.313,0.198 10 false ACC
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
4K-1 - MB-30 (ACC) Battery not connected to 4A-28 and 4A-27 10 kΩ or higher
4K-1 - MB-30 (ACC) Battery positive (+) → 4A-28
Battery negative (-) → 4A-27
Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

6.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ACC SW Ignition switch ACC signal ON or OFF ON: Ignition switch ACC
OFF: Ignition switch off
"ON" is also displayed for this item when the ignition switch is ON.
Body Electrical > Main Body > Data List
Tester Display
ACC SW
50003 123 31
OK:

Normal conditions listed above are displayed.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

7.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - ACC RELAY POWER SOURCE AND BODY GROUND)
7.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - ACC RELAY POWER SOURCE AND BODY GROUND)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
4A-28 - Body ground Ignition switch ACC 11 to 14 V



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (BATTERY POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (BATTERY POWER SOURCE)
a.

Disconnect the 4A and 4K instrument panel junction block assembly connectors.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
4K-1 - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4A-27 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

9.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

E288979C01
1.51,0.406 1.823,0.667 0.313,0.26 4.75,0.354 5.063,0.615 0.313,0.26 3.344,2.198 3.656,2.458 0.313,0.26 4.771,3.417 4.938,3.417 4.938,3.417 5.188,2.917 false 0.188,0.156 0.5,0.354 0.313,0.198 10 false *a 1.583,0.448 1.896,0.646 0.313,0.198 10 false 4K 4.823,0.406 5.135,0.604 0.313,0.198 10 false 4A 3.406,2.26 3.719,2.458 0.313,0.198 10 false MB 4.427,3.333 4.74,3.531 0.313,0.198 10 false ACC
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
4K-1 - MB-30 (ACC) Battery not connected to 4A-28 and 4A-27 10 kΩ or higher
4K-1 - MB-30 (ACC) Battery positive (+) → 4A-28
Battery negative (-) → 4A-27
Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY