Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM
RM3160E _58 Vehicle Interior _019707 LIGHTING (INT) _0103507 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  Rear Door Courtesy Switch Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) detects the condition of the rear door courtesy light switch assembly.

WIRING DIAGRAM

E287408E01
0.896,1.458 1.208,1.656 0.313,0.198 10 false L13 0.917,2.49 1.229,2.688 0.313,0.198 10 false M14 0.896,1.625 3.896,1.854 3,0.229 10 false Rear Door Courtesy Light Switch Assembly RH 0.906,2.677 3.906,2.906 3,0.229 10 false Rear Door Courtesy Light Switch Assembly LH 4.052,1 4.365,1.198 0.313,0.198 10 false 30 4.063,2.021 4.375,2.219 0.313,0.198 10 false 36 4.052,1.198 4.365,1.396 0.313,0.198 10 false 4D 5.958,3.313 6.271,3.51 0.313,0.198 10 false MB 4.052,2.219 4.365,2.417 0.313,0.198 10 false 4H 5.969,2.115 6.281,2.313 0.313,0.198 10 false 13 6.042,1.104 6.354,1.302 0.313,0.198 10 false 2 6.24,1.208 6.854,1.406 0.615,0.198 10 false RCTY 6.229,2.208 6.844,2.406 0.615,0.198 10 false LCTY 4.302,2.906 5.917,3.396 1.615,0.49 10 false Instrument Panel Junction Block Assembly 5.969,3.5 7.135,4.094 1.167,0.594 10 false Main Body ECU (Multiplex Network Body ECU) 2.906,1.083 3.219,1.281 0.313,0.198 10 false 1 2.896,2.104 3.208,2.302 0.313,0.198 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.*1

·

As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.*2

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION


*1: w/ Smart Entry and Start System

*2: for LHD



PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Door Courtesy SW Rear door courtesy light switch assembly RH signal ON or OFF ON: Rear door RH open
OFF: Rear door RH closed
-
RL Door Courtesy SW Rear door courtesy light switch assembly LH signal ON or OFF ON: Rear door LH open
OFF: Rear door LH closed
-
Body Electrical > Main Body > Data List
Tester Display
RR Door Courtesy SW
RL Door Courtesy SW
50003 123 24,25
OK:

Normal conditions listed above are displayed.



Result:
Result Proceed to
OK A
RR Door Courtesy SW is not normal B
RL Door Courtesy SW is not normal C



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

2.INSPECT REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY RH

C

5.INSPECT REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY LH
2.INSPECT REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY RH
a.

Remove the rear door courtesy light switch assembly RH.

Click hereVehicle Interior>LIGHTING (INT)>REAR DOOR COURTESY SWITCH>REMOVAL


b.

Inspect the rear door courtesy light switch assembly RH.

Click hereVehicle Interior>LIGHTING (INT)>REAR DOOR COURTESY SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY RH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPLACE REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY RH

3.CHECK HARNESS AND CONNECTOR (REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY RH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 4D instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L13-1 - 4D-30 Always Below 1 Ω
L13-1 or 4D-30 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

E273530C22
4.656,0.531 5.01,0.792 0.354,0.26 1.24,0.323 1.615,0.563 0.375,0.24 3.396,1.115 3.5,1.5 3.5,1.5 3.729,1.5 false 1.354,0.354 1.667,0.552 0.313,0.198 10 false 4D 4.74,0.583 5.052,0.781 0.313,0.198 10 false MB 3.792,1.417 4.292,1.615 0.5,0.198 10 false RCTY 0.281,0.135 0.594,0.333 0.313,0.198 10 false *a
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
4D-30 - MB-2 (RCTY) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

5.INSPECT REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY LH
a.

Remove the rear door courtesy light switch assembly LH.

Click hereVehicle Interior>LIGHTING (INT)>REAR DOOR COURTESY SWITCH>REMOVAL


b.

Inspect the rear door courtesy light switch assembly LH.

Click hereVehicle Interior>LIGHTING (INT)>REAR DOOR COURTESY SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY LH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPLACE REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY LH

6.CHECK HARNESS AND CONNECTOR (REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY LH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 4H instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M14-1 - 4H-36 Always Below 1 Ω
M14-1 or 4H-36 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

E273529C09
1.354,0.25 1.708,0.49 0.354,0.24 4.875,0.448 5.24,0.708 0.365,0.26 4.771,1.073 4.906,1.49 4.906,1.49 5.135,1.49 false 4.969,0.5 5.354,0.75 0.385,0.25 10 false MB 1.458,0.292 1.771,0.49 0.313,0.198 10 false 4H 5.208,1.396 5.646,1.583 0.438,0.188 10 false LCTY 0.271,0.135 0.583,0.333 0.313,0.198 10 false *a
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
4H-36 - MB-13 (LCTY) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY