Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM
RM3160E _58 Vehicle Interior _019707 LIGHTING (INT) _0103507 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  Interior Light Auto Cut Circuit  


DESCRIPTION

When the battery saving control operates, the main body ECU (multiplex network body ECU) controls the operation of the DOME CUT relay that is built into the instrument panel junction block assembly to turn off the interior lights.

WIRING DIAGRAM

E287262
0.521,0.885 1.354,1.052 0.833,0.167 10 false from Battery 0.333,2.438 1.667,2.604 1.333,0.167 10 false to each Interior Light 3.333,3.792 6,3.958 2.667,0.167 10 false Instrument Panel Junction Block Assembly 5.917,4.583 6.177,4.771 0.26,0.188 10 false MB 2.979,2.854 3.271,3.021 0.292,0.167 10 false 4D 2.969,2.052 3.26,2.219 0.292,0.167 10 false 4H 2.979,0.906 3.271,1.073 0.292,0.167 10 false 4L 3,0.698 3.177,0.865 0.177,0.167 10 false 1 3.01,1.854 3.271,2.021 0.26,0.167 10 false 5 3.01,2.646 3.271,2.813 0.26,0.167 10 false 7 1.979,1.063 2.948,1.24 0.969,0.177 10 false J/B-B 4.646,1.552 5.417,1.719 0.771,0.167 10 false DOME CUT 5.948,0.802 6.198,0.969 0.25,0.167 10 false 23 6.24,0.896 6.74,1.063 0.5,0.167 10 false DOMR 5.917,4.75 7.083,5.25 1.167,0.5 10 false Main Body ECU (Multiplex Network Body ECU) 3.583,1.063 4.083,1.229 0.5,0.167 10 false DOME

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure

·

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.*1

·

As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.*2

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION


*1: w/ Smart Entry and Start System

*2: for LHD



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Relay for Interior Light Auto Cut Function DOME CUT relay ON or OFF When performing this Active Test, turn on each interior lights.
·

ON: DOME CUT relay off (interior lights turn off)

·

OFF: DOME CUT relay on (interior lights turn on)


Body Electrical > Main Body > Active Test
Tester Display
Relay for Interior Light Auto Cut Function
50004 123 66
OK:

DOME CUT relay operates.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (POWER SOURCE - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 4L instrument panel junction block assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
4L-1 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


c.

Measure the voltage according to the value(s) in the table below.

E275740
1.26,0.448 1.74,0.698 0.479,0.25 4.938,0.396 5.417,0.646 0.479,0.25 0.875,2.167 1.354,2.417 0.479,0.25 4.281,2.385 4.76,2.635 0.479,0.25 4.896,3.354 5.125,3.354 5.125,3.354 5.313,3.021 false 0.365,0.24 0.677,0.438 0.313,0.198 10 false *a 1.427,0.49 1.76,0.708 0.333,0.219 10 false 4D 5.104,0.427 5.438,0.646 0.333,0.219 10 false 4H 1.042,2.208 1.375,2.427 0.333,0.219 10 false 4L 4.427,2.427 4.76,2.646 0.333,0.219 10 false MB 4.448,3.26 5.021,3.583 0.573,0.323 10 false DOMR
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


Standard Voltage:
Tester Connection Condition Specified Condition
4H-5 - Battery negative terminal Battery positive (+) → 4L-1
Battery negative (-) → MB-23 (DOMR)
11 to 14 V
4D-7 - Battery negative terminal Battery positive (+) → 4L-1
Battery negative (-) → MB-23 (DOMR)
11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY