Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM
RM3160E _58 Vehicle Interior _019707 LIGHTING (INT) _0103507 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  Ambient Light Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the ambient lights.

WIRING DIAGRAM

E287266E06
5.99,5.813 6.302,5.979 0.313,0.167 10 false MB 3.458,5.031 6.125,5.198 2.667,0.167 10 false Instrument Panel Junction Block Assembly 2.208,0.875 3.104,1.052 0.896,0.177 10 false J/B-B 0.615,0.708 1.448,0.875 0.833,0.167 10 false from Battery 4.708,1.365 5.542,1.531 0.833,0.167 10 false DOME CUT 5.958,0.625 6.271,0.792 0.313,0.167 10 false 23 5.958,2.427 6.271,2.594 0.313,0.167 10 false 26 6.24,0.74 6.74,0.906 0.5,0.167 10 false DOMR 6.24,2.531 6.656,2.698 0.417,0.167 10 false LED1 2.448,2.427 2.583,2.594 0.135,0.167 10 false 2 2.438,4.219 2.573,4.385 0.135,0.167 10 false 2 2.438,5.979 2.573,6.146 0.135,0.167 10 false 2 2.438,7.781 2.573,7.948 0.135,0.167 10 false 2 3.073,6.573 5.406,6.74 2.333,0.167 10 false F30 3.125,8.354 5.458,8.521 2.333,0.167 10 false F31 0.26,8.333 2.094,8.5 1.833,0.167 10 false H16 0.24,6.552 2.073,6.719 1.833,0.167 10 false I15 0.365,3 2.115,3.167 1.75,0.167 10 false K7 0.219,4.771 1.969,4.938 1.75,0.167 10 false J7 0.646,2.427 0.844,2.594 0.198,0.167 10 false + 0.625,4.198 0.823,4.365 0.198,0.167 10 false + 0.635,5.99 0.833,6.156 0.198,0.167 10 false + 0.635,7.771 0.833,7.938 0.198,0.167 10 false + 2.24,7.781 2.396,7.948 0.156,0.167 10 false - 2.271,5.969 2.427,6.135 0.156,0.167 10 false - 2.271,4.219 2.427,4.385 0.156,0.167 10 false - 2.281,2.438 2.438,2.604 0.156,0.167 10 false - 0.458,2.438 0.594,2.604 0.135,0.167 10 false 1 0.469,4.208 0.604,4.375 0.135,0.167 10 false 1 0.438,5.99 0.573,6.156 0.135,0.167 10 false 1 0.417,7.771 0.552,7.938 0.135,0.167 10 false 1 5.979,6 7.146,6.5 1.167,0.5 10 false Main Body ECU (Multiplex Network Body ECU) 3.198,0.729 3.479,0.896 0.281,0.167 10 false 4L 3.188,1.313 3.469,1.479 0.281,0.167 10 false 4D 3.188,1.917 3.469,2.083 0.281,0.167 10 false 4H 3.188,2.51 3.469,2.677 0.281,0.167 10 false 4H 3.177,4.313 3.458,4.479 0.281,0.167 10 false 4D 3.229,4.094 3.51,4.26 0.281,0.167 10 false 9 3.198,2.313 3.479,2.479 0.281,0.167 10 false 27 3.24,0.521 3.521,0.688 0.281,0.167 10 false 1 3.208,1.708 3.49,1.875 0.281,0.167 10 false 22 3.188,1.115 3.469,1.281 0.281,0.167 10 false 31 0.354,3.167 2.802,3.479 2.448,0.313 10 false Rear Door Trim Board Sub-assembly LH (Rear Door Ambient Light LH) 0.208,4.938 2.698,5.333 2.49,0.396 10 false Rear Door Trim Board Sub-assembly RH (Rear Door Ambient Light RH) 0.229,6.719 2.719,7.083 2.49,0.365 10 false Front Door Trim Board Sub-assembly LH (Front Door Ambient Light LH) 0.26,8.49 2.771,8.865 2.51,0.375 10 false Front Door Trim Board Sub-assembly RH (Front Door Ambient Light RH) 3.073,6.75 5.583,7.156 2.51,0.406 10 false No. 1 Interior Illumination Light Assembly (Driver Side) 3.125,8.51 5.646,8.875 2.521,0.365 10 false No. 1 Interior Illumination Light Assembly (Passenger Side) 3.188,6 3.323,6.167 0.135,0.167 10 false 2 3.198,7.771 3.333,7.938 0.135,0.167 10 false 2 5.26,5.958 5.573,6.125 0.313,0.167 10 false ILL- 5.24,7.74 5.552,7.906 0.313,0.167 10 false ILL- 5.552,6.01 5.688,6.177 0.135,0.167 10 false 1 5.563,7.781 5.698,7.948 0.135,0.167 10 false 1 3.344,5.948 3.677,6.115 0.333,0.167 10 false ILL+ 3.344,7.74 3.656,7.906 0.313,0.167 10 false ILL+ 3.76,0.875 4.26,1.042 0.5,0.167 10 false DOME

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.*1

·

As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.*2

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION


*1: w/ Smart Entry and Start System

*2: for LHD



PROCEDURE

1.CONFIRM SYMPTOMS
a.

Confirm problem symptoms.


Result:
Result Proceed to
Ambient lights do not come on A
Ambient light dimmer control does not operate B



A

2.PERFORM ACTIVE TEST USING GTS

B

5.PERFORM ACTIVE TEST USING GTS
2.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

Check that the ambient lights come on.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Interior Illumination Light1 Ambient lights ON or OFF Precondition for using the Active Test to turn lights on and off:
·

Ignition switch is turned off just before performing the Active Test.


Body Electrical > Main Body > Active Test
Tester Display
Interior Illumination Light1
50004 123 68
OK:

All ambient lights come on.



Result:
Result Proceed to
OK A
NG (All ambient lights do not illuminate) B
NG (Ambient light does not illuminate (for Front Door)) C
NG (Ambient light does not illuminate (for Rear Door))
NG (Ambient light does not illuminate (for Instrument Panel Side))



A

PROBLEM SYMPTOMS TABLE FOR EACH PROBLEM SYMPTOM

B

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

C

GO TO PROBLEM SYMPTOMS TABLE FOR EACH PROBLEM SYMPTOM

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 4L instrument panel junction block assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
4L-1 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

E274451C05
1.583,0.271 2.01,0.521 0.427,0.25 5.135,0.281 5.563,0.531 0.427,0.25 1.24,1.99 1.667,2.24 0.427,0.25 4.698,2.188 5.125,2.438 0.427,0.25 5.385,3.24 5.625,3.24 5.625,3.24 6.031,2.802 false 0.49,0.333 0.917,0.76 0.427,0.427 10 false *a 5,3.156 5.427,3.583 0.427,0.427 10 false LED1 1.729,0.323 2.156,0.75 0.427,0.427 10 false 4D 5.281,0.323 5.698,0.51 0.417,0.188 10 false 4H 1.385,2.021 1.667,2.25 0.281,0.229 10 false 4L 4.833,2.25 5.26,2.677 0.427,0.427 10 false MB
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
4L-1 - 4H-22 Always Below 1 Ω
4L-1 - 4D-31 Always Below 1 Ω
4H-27 - MB-26 (LED1) Always Below 1 Ω
4D-9 - MB-26 (LED1) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

5.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

Check that the ambient lights come on.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Interior Illumination Light1 Ambient lights ON or OFF Preconditions for using the Active Test to check dimmer controlled illumination:
·

Engine running

·

Shift lever is in any position other than P.


Body Electrical > Main Body > Active Test
Tester Display
Interior Illumination Light1
50004 123 68
OK:

Ambient light dimmer control operates.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)