Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › 2013.12–2016.11
RM3160E _59 Vehicle Exterior _019722 LIGHTING (EXT) _0103403 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Rear Fog Light Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the rear fog lights.

WIRING DIAGRAM

E288862
1.333,4.135 3.229,4.333 1.896,0.198 10 false Rear Fog Light Assembly LH 1.333,3.969 1.792,4.167 0.458,0.198 10 false W6 1.333,5 1.792,5.198 0.458,0.198 10 false W5 1.333,5.167 3.229,5.365 1.896,0.198 10 false Rear Fog Light Assembly RH 0.625,1 1.458,1.198 0.833,0.198 10 false from Battery 2.458,1.188 2.917,1.385 0.458,0.198 10 false ALT 1.333,2.583 2.708,2.781 1.375,0.198 10 false RR FOG LP 2.323,1.948 3.24,2.146 0.917,0.198 10 false FOG RR 3.417,3.25 7.156,3.531 3.74,0.281 10 false Instrument Panel Junction Block Assembly 5.448,3.833 7.073,4.24 1.625,0.406 10 false Main Body ECU (Multiplex Network Body ECU) 3.438,1.031 3.75,1.229 0.313,0.198 10 false 4K 3.438,2.292 3.75,2.49 0.313,0.198 10 false 4H 3.438,2.76 3.75,2.958 0.313,0.198 10 false 4H 4.635,1.719 5.25,1.917 0.615,0.198 10 false TAIL 4.635,2.427 5.25,2.625 0.615,0.198 10 false TAIL 3.479,0.802 3.667,1 0.188,0.198 10 false 1 3.427,2.083 3.708,2.344 0.281,0.26 10 false 16 3.458,2.563 3.646,2.76 0.188,0.198 10 false 26 5.927,0.917 6.198,1.104 0.271,0.188 10 false 14 5.938,2.646 6.26,2.927 0.323,0.281 10 false 27 6.188,1.031 6.802,1.229 0.615,0.198 10 false TRLY 6.198,2.76 6.813,2.958 0.615,0.198 10 false RFGO 1.313,1.688 1.5,1.885 0.188,0.198 10 false 3 1.313,2.167 1.5,2.365 0.188,0.198 10 false 1 2,1.688 2.188,1.885 0.188,0.198 10 false 5 2,2.167 2.188,2.365 0.188,0.198 10 false 2 1.479,3.635 1.667,3.833 0.188,0.198 10 false 1 1.479,4.698 1.667,4.896 0.188,0.198 10 false 1 2.813,3.635 3,3.833 0.188,0.198 10 false 2 2.813,4.688 3,4.885 0.188,0.198 10 false 2 5.448,3.656 6.063,3.854 0.615,0.198 10 false MB

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses and bulbs for circuits related to this system before performing the following procedure.

·

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.*

*: w/ Smart Entry and Start System


·

As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

*: for LHD




PROCEDURE

1.CHECK OPERATION (TAILLIGHTS)
a.

Check the operation of the taillights.

OK:

Taillights operate normally.



Result:
Proceed to
OK
NG



OK

2.PERFORM ACTIVE TEST USING GTS

NG

2.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

Check that the relay operates.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Rear Fog Light Relay Rear fog light relay ON/OFF Light control switch in tail position
Body Electrical > Main Body > Active Test
Tester Display
Rear Fog Light Relay
50004 123 17
OK:

Rear fog light relay operates. (Rear fog lights come on.)



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

3.INSPECT RR FOG LP RELAY
3.INSPECT RR FOG LP RELAY
a.
E222294
1.073,0.958 1.302,0.49 1.302,0.49 1.438,0.49 false 1.063,1.333 1.146,1.75 1.146,1.75 1.344,1.75 false 0.802,1.01 0.938,0.49 0.938,0.49 1.063,0.49 false 0.563,1.281 0.635,1.76 0.635,1.76 0.823,1.76 false 1.458,0.406 1.563,0.563 0.104,0.156 10 false 1 1.375,1.667 1.479,1.823 0.104,0.156 10 false 2 1.094,0.396 1.198,0.552 0.104,0.156 10 false 5 0.844,1.667 0.948,1.823 0.104,0.156 10 false 3 0.219,0.156 0.667,0.5 0.448,0.344 10 false *a
*a Component without harness connected
(RR FOG LP Relay)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Voltage not applied between terminals 1 and 2 10 kΩ or higher
3 - 5 Voltage applied between terminals 1 and 2 Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (RR FOG LP RELAY INPUT VOLTAGE)

NG

REPLACE RR FOG LP RELAY

4.CHECK HARNESS AND CONNECTOR (RR FOG LP RELAY INPUT VOLTAGE)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Relay terminal 5 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (RR FOG LP RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (RR FOG LP RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 4H instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Relay terminal 1 - 4H-26 Always Below 1 Ω
Relay terminal 2 - 4H-16 Always Below 1 Ω
Relay terminal 1 - Body ground Always 10 kΩ or higher
Relay terminal 2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (RR FOG LP RELAY - REAR FOG LIGHT ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (RR FOG LP RELAY - REAR FOG LIGHT ASSEMBLY)
a.

for LH Side:

i.

Disconnect the W6 rear light assembly LH connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Relay terminal 3 - W6-1 Always Below 1 Ω
Relay terminal 3 - Body ground Always 10 kΩ or higher




b.

for RH Side:

i.

Disconnect the W5 rear light assembly RH connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Relay terminal 3 - W5-1 Always Below 1 Ω
Relay terminal 3 - Body ground Always 10 kΩ or higher




Result:
Proceed to
OK
NG



OK

7.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

E259755C03
4.823,0.375 5.135,0.594 0.313,0.219 3.417,2.24 3.729,2.458 0.313,0.219 2.063,0.375 2.375,0.594 0.313,0.219 3.146,3.177 3.302,2.875 false 0.219,0.125 0.531,0.323 0.313,0.198 10 false *a 4.906,0.417 5.219,0.615 0.313,0.198 10 false 4H 3.49,2.281 3.802,2.479 0.313,0.198 10 false MB 2.927,3.198 3.406,3.396 0.479,0.198 10 false TRLY 2.146,0.417 2.458,0.615 0.313,0.198 10 false 4K
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -



c.

Connect a positive (+) lead from the battery to terminal 4K-1.


d.

Connect a negative (-) lead from the battery to terminal MB-14 (TRLY).


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
4H-16 - Battery negative (-) terminal Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

8.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

8.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Measure the resistance according to the value(s) in the table below.

E289164C01
1.333,0.26 1.729,0.49 0.396,0.229 4.813,0.417 5.208,0.646 0.396,0.229 5.698,1.406 6.115,0.99 false 0.385,0.177 0.656,0.531 0.271,0.354 10 false *a 1.458,0.292 1.729,0.646 0.271,0.354 10 false 4H 4.917,0.448 5.188,0.802 0.271,0.354 10 false MB 5.281,1.354 5.823,1.563 0.542,0.208 10 false RFGO
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
4H-26 - MB-27 (RFGO) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY