Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for Navigation Receiver Type)
RM3160E _56 Audio / Visual / Telematics _019701 NAVIGATION / MULTI INFO DISPLAY _0104171 NAVIGATION SYSTEM(for Navigation Receiver Type) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Navigation Receiver Type)  Microphone Circuit between Microphone and Navigation Receiver Assembly  


DESCRIPTION

The navigation receiver assembly and map light assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.

Using this circuit, the navigation receiver assembly sends power to the map light assembly (telephone microphone assembly), and the map light assembly (telephone microphone assembly) sends microphone signals to the navigation receiver assembly.

WIRING DIAGRAM

E268499E21
0.833,0.802 1.333,0.969 0.5,0.167 10 false MACC 0.844,1.271 1.344,1.438 0.5,0.167 10 false MCO+ 0.865,1.75 1.365,1.917 0.5,0.167 10 false MCO- 0.865,2.698 1.281,2.865 0.417,0.167 10 false SNS2 0.167,3.156 0.417,3.323 0.25,0.167 10 false S1 0.167,3.323 2.135,3.698 1.969,0.375 10 false Map Light Assembly (Telephone Microphone Assembly) 3.281,2.083 4.052,2.292 0.771,0.208 10 false (Shielded) 5.927,0.802 6.427,0.969 0.5,0.167 10 false MACC 5.927,1.271 6.344,1.438 0.417,0.167 10 false MIN+ 5.927,1.75 6.26,1.917 0.333,0.167 10 false MIN- 5.927,2.229 6.427,2.396 0.5,0.167 10 false SGND 5.927,2.698 6.344,2.865 0.417,0.167 10 false SNS2 5.854,3.146 6.365,3.427 0.51,0.281 10 false F116 5.854,3.313 7.063,3.698 1.208,0.385 10 false Navigation Receiver Assembly 1.333,0.698 1.583,0.875 0.25,0.177 10 false 3 1.333,1.167 1.615,1.344 0.281,0.177 10 false 2 1.333,1.646 1.615,1.823 0.281,0.177 10 false 4 1.323,2.594 1.531,2.76 0.208,0.167 10 false 13 5.74,0.698 5.906,0.865 0.167,0.167 10 false 4 5.74,1.167 5.906,1.333 0.167,0.167 10 false 5 5.74,2.594 5.906,2.76 0.167,0.167 10 false 6 5.667,1.646 5.917,1.813 0.25,0.167 10 false 19 5.667,2.125 5.917,2.292 0.25,0.167 10 false 18

PROCEDURE

1.CHECK MICROPHONE (OPERATION CHECK)
a.
E268457

Enter the "Microphone Check" screen. Refer to Check Microphone in Operation Check.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Navigation Receiver Type)>OPERATION CHECK


b.

When a voice is input into the microphone, check that the microphone input level meter changes according to the input voice.


c.

Push the recording switch and perform voice recording.

HINT:
·

Select the recording switch with the blower motor of the air conditioning system stopped. If an outlet of the air conditioning system is facing the microphone, noise may be recorded.

·

Voice can be recorded for up to 5 seconds.




d.

Check that the recording indicator remains on while recording and that the recorded voice is played normally without noise or distortion.

OK:

All check results are normal.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
a.

Disconnect the F116 navigation receiver assembly connector.


b.

Disconnect the S1 map light assembly (telephone microphone assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F116-6 (SNS2) - S1-13 (SNS2) Always Below 1 Ω
F116-4 (MACC) - S1-3 (MACC) Always Below 1 Ω
F116-5 (MIN+) - S1-2 (MCO+) Always Below 1 Ω
F116-19 (MIN-) - S1-4 (MCO-) Always Below 1 Ω
F116-6 (SNS2) - Body ground Always 10 kΩ or higher
F116-4 (MACC) - Body ground Always 10 kΩ or higher
F116-5 (MIN+) - Body ground Always 10 kΩ or higher
F116-19 (MIN-) - Body ground Always 10 kΩ or higher
F116-18 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT NAVIGATION RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT NAVIGATION RECEIVER ASSEMBLY
a.

Reconnect the F116 navigation receiver assembly connector.


b.

Reconnect the S1 map light assembly (telephone microphone assembly) connector.


c.
E176671C72
1.51,0.542 1.917,0.813 0.406,0.271 2.229,2.01 2.896,2.698 false 2.229,1.74 2.854,1.302 false 2.052,2.01 1.385,2.698 false 1.563,0.583 2.146,0.969 0.583,0.385 10 false F116 0.24,0.177 0.615,0.542 0.375,0.365 10 false *a 2.75,2.708 3.26,3 0.51,0.292 10 false SGND 2.875,1.198 3.427,1.594 0.552,0.396 10 false MACC 1.167,2.708 1.688,2.979 0.521,0.271 10 false MIN-
*a Component with harness connected
(Navigation Receiver Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F116-4 (MACC) - Body ground Engine switch on (ACC) 4 to 6 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F116-18 (SGND) - Body ground Always Below 1 Ω
F116-19 (MIN-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

NG

4.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
a.

Remove the map light assembly (telephone microphone assembly).

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.
E287094C02
2.302,1.729 2.177,1.385 false 2.125,0.74 1.979,1.219 false 0.188,0.146 0.5,0.302 0.313,0.156 10 false *a 2.26,1.76 2.792,2.01 0.531,0.25 10 false SNS2 2.094,0.552 2.625,0.802 0.531,0.25 10 false MCO-
*a Component without harness connected
(Map Light Assembly (Telephone Microphone Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (MCO-) - 13 (SNS2) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

NG

REPLACE MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

5.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
a.

Reconnect the F116 navigation receiver assembly connector.


b.

Reconnect the S1 map light assembly (telephone microphone assembly) connector.


c.

Turn the engine switch on (ACC).


d.
E287103C03
1.521,0.156 1.917,0.396 0.396,0.24 2.083,1.208 2.24,0.438 false 1.896,1.219 0.969,0.615 false 0.104,0.094 0.271,0.26 0.167,0.167 10 false *a 1.635,0.198 1.885,0.365 0.25,0.167 10 false S1 2.198,0.24 2.698,0.406 0.5,0.167 10 false MCO+ 0.573,0.479 1.073,0.646 0.5,0.167 10 false MCO-
*a Component with harness connected
(Map Light Assembly (Telephone Microphone Assembly))


Connect an oscilloscope to terminals 2 (MCO+) and 4 (MCO-) of the S1 map light assembly (telephone microphone assembly) connector.


e.

Check the waveform of the map light assembly (telephone microphone assembly) using the oscilloscope.

Result:
Result Proceed to
A waveform synchronized with the voice input to the map light assembly (telephone microphone assembly) is output. A
A waveform synchronized with the voice input to the map light assembly (telephone microphone assembly) is not output. B




A

B

REPLACE MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)