Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for Navigation Receiver Type) › 2013.12–2016.11
RM3160E _56 Audio / Visual / Telematics _019701 NAVIGATION / MULTI INFO DISPLAY _0104171 NAVIGATION SYSTEM(for Navigation Receiver Type) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Navigation Receiver Type)  AVC-LAN Circuit  


DESCRIPTION

Each unit of the navigation system connected to the AVC-LAN (communication bus) transfers switch signals through the AVC-LAN.

If a short to +B or short to ground occurs in the AVC-LAN, the navigation system will not function normally because communication is not possible.

WIRING DIAGRAM

E277861
0.885,1.865 2.854,2.073 1.969,0.208 10 false Television Display Assembly 4.927,1.854 6.875,2.073 1.948,0.219 10 false Navigation Receiver Assembly 0.938,2.396 2.938,2.615 2,0.219 10 false : AVC-LAN Communication Line 1.75,0.406 2.365,0.604 0.615,0.198 10 false TX1+ 1.771,1.177 2.385,1.375 0.615,0.198 10 false TX1- 0.875,1.688 1.49,1.885 0.615,0.198 10 false S8 4.927,1.688 5.542,1.885 0.615,0.198 10 false F118 5.083,0.385 5.698,0.583 0.615,0.198 10 false TX+ 5.094,1.188 5.708,1.385 0.615,0.198 10 false TX- 4.906,0.271 5.521,0.469 0.615,0.198 10 false 9 4.844,1.052 5.458,1.25 0.615,0.198 10 false 10 2.146,0.271 2.76,0.469 0.615,0.198 10 false 3 2.156,1.052 2.771,1.25 0.615,0.198 10 false 4

CAUTION / NOTICE / HINT

HINT:

The navigation receiver assembly is the master unit.


PROCEDURE

1.INSPECT NAVIGATION RECEIVER ASSEMBLY

b.
E231034
1.479,1.594 1.625,1.25 false 1.885,1.583 1.76,1.25 false 0.094,0.094 0.406,0.292 0.313,0.198 10 false *a 1.323,1.625 1.781,1.823 0.458,0.198 10 false TX- 1.865,1.625 2.323,1.823 0.458,0.198 10 false TX+
*a Component without harness connected
(Navigation Receiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
9 (TX+) - 10 (TX-) Always 60 to 80 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (AVC-LAN CIRCUIT)

NG

2.CHECK HARNESS AND CONNECTOR (AVC-LAN CIRCUIT)
a.

Disconnect the F118 navigation receiver assembly connector.


b.

Disconnect the S8 television display assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F118-9 (TX+) - S8-3 (TX1+) Always Below 1 Ω
F118-10 (TX-) - S8-4 (TX1-) Always Below 1 Ω
F118-9 (TX+) - Body ground Always 10 kΩ or higher
F118-10 (TX-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT MALFUNCTIONING PARTS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT MALFUNCTIONING PARTS
a.

Disconnect and reconnect each slave unit one by one until the master unit returns to normal operation.

HINT:
·

Check all slave units.

·

If disconnecting a slave unit causes the master unit to return to normal operation, the slave unit is defective and should be replaced.



OK:

Master unit returns to normal operation.



Result:
Proceed to
OK
NG



OK

REPLACE MALFUNCTIONING PARTS

NG