Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM
RM3160E _55 Steering _019697 POWER ASSIST SYSTEMS _0104490 POWER STEERING SYSTEM D

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  DTC CHECK / CLEAR  


CHECK DTCs (USING GTS)


a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / EMPS / Trouble Codes.

Chassis > EMPS > Trouble Codes
50001 142



CHECK DTCs (USING SST CHECK WIRE)


a.
C248264C04
1.594,0.813 1.594,0.406 false 1.865,1.5 1.865,1.865 false 1.49,0.219 1.719,0.365 0.229,0.146 10 CG 1.781,1.896 2.01,2.042 0.229,0.146 10 TC 0.156,0.104 0.458,0.49 0.302,0.385 10 *a
*a DLC3


Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

SST
09843-18040  


b.

Turn the ignition switch to ON.


c.
C276865C04
1.917,3.396 2.083,2.75 false 1.438,3.396 1.583,2.917 false 2.271,3.396 2.417,2.917 false 1.167,3.396 1.333,2.75 false 1.083,3.396 1,2.917 false 0.167,0.146 0.344,0.333 0.177,0.188 10 *a 0.573,1.26 0.813,1.448 0.24,0.188 10 *c 0.583,1.75 0.885,1.938 0.302,0.188 10 *d 0.167,2.396 0.438,2.667 0.271,0.271 10 *b 1.281,4.052 1.844,4.229 0.563,0.177 10 *f 2.292,4.042 2.854,4.219 0.563,0.177 10 *g 2.104,4.354 2.771,4.531 0.667,0.177 10 (*e) 1.177,0.844 1.479,1.031 0.302,0.188 10 0.25 2.208,0.615 2.51,0.802 0.302,0.188 10 0.25 0.833,3.417 0.948,3.604 0.115,0.188 10 4 0.885,2.75 1.115,2.938 0.229,0.188 10 0.5 1.25,2.583 1.479,2.771 0.229,0.188 10 0.5 1.5,2.75 1.729,2.938 0.229,0.188 10 1.5 2.365,2.75 2.594,2.938 0.229,0.188 10 0.5 2,2.583 2.229,2.771 0.229,0.188 10 2.5 0.26,3.469 0.5,3.656 0.24,0.188 10 *c 0.271,3.906 0.573,4.094 0.302,0.188 10 *d 2.708,1.99 3.167,2.333 0.458,0.344 10 (*e)
*a Normal System Code
*b Codes 21 and 22
*c ON
*d OFF
*e Seconds
*f Code 21
*g Code 22


Read and write down any DTCs indicated by the blinking of the EPS warning light on the combination meter assembly. Refer to the illustration to the right for examples of the normal system code and DTCs 21 and 22.

HINT:
·

If the EPS warning light does not blink to display stored DTCs or the normal system code, inspect the circuit shown in the table below.

Trouble Area Link
EPS warning light circuit (Click here)

·

If two or more malfunctions are detected simultaneously, DTCs will be displayed in ascending numerical order.




d.

Refer to Diagnostic Trouble Code Chart for DTC information.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>DIAGNOSTIC TROUBLE CODE CHART


e.

Check the details of the DTCs.

EPS DTC
EPS Warning Light Display Tester Display
11 C1511
C1512
C1513
C1514
12 C1528
13 C1541
22 C1552
23 C1554
24 C1524
25 C1521
C1531
C1532
C1533
C1534
C1551
C1555
26 C1581
C1582
41 U0100
42 U0129



CLEAR DTCs (USING GTS)


a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / EMPS / Trouble Codes.

Chassis > EMPS > Clear DTCs
50002 142


g.

Turn the ignition switch off.


h.

Disconnect the GTS from the DLC3.



CLEAR DTCs (USING SST CHECK WIRE)


a.
C248264C05
1.625,0.813 1.625,0.406 false 1.635,1.51 1.438,1.823 false 1.885,1.5 2.052,1.833 false 1.521,0.229 1.75,0.375 0.229,0.146 10 CG 1.323,1.875 1.521,2.021 0.198,0.146 10 TS 2.021,1.885 2.24,2.031 0.219,0.146 10 TC 0.156,0.146 0.521,0.448 0.365,0.302 10 *a
*a DLC3


Using SST, connect terminals 12 (TS) and 4 (CG) of the DLC3, and also terminals 13 (TC) and 4 (CG) of the DLC3.

SST
09843-18040  


b.

Turn the ignition switch to ON.


c.

Disconnect and reconnect terminal 13 (TC) of the DLC3 4 times or more within 8 seconds.


d.

Check that the EPS warning light blinks the normal system code.


e.

Turn the ignition switch off.


f.

Remove SST from the DLC3.