Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM
RM3160E _55 Steering _019697 POWER ASSIST SYSTEMS _0104490 POWER STEERING SYSTEM C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  C1511  Torque Sensor1  C1512  Torque Sensor2  C1513  Torque Sensor Deviation Excessive  C1514  Torque Sensor Power Supply Voltage  


DESCRIPTION

The torque sensor converts the rotation torque received from the steering wheel into electric signals and sends them to the power steering ECU assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Note
C1511 Torque Sensor1 Torque sensor malfunction
·

Torque sensor (Electric power steering column sub-assembly)

·

Power steering ECU assembly


EPS warning light: Comes on -
C1512 Torque Sensor2 Torque sensor malfunction
·

Torque sensor (Electric power steering column sub-assembly)

·

Power steering ECU assembly


EPS warning light: Comes on -
C1513 Torque Sensor Deviation Excessive Torque sensor malfunction
·

Torque sensor (Electric power steering column sub-assembly)

·

Power steering ECU assembly


EPS warning light: Comes on -
C1514 Torque Sensor Power Supply Voltage Torque sensor malfunction
·

Torque sensor (Electric power steering column sub-assembly)

·

Power steering ECU assembly


EPS warning light: Comes on -

WIRING DIAGRAM

C240198
4.448,3.073 6.438,3.292 1.99,0.219 10 false Power Steering ECU Assembly 0.563,2.948 3,3.354 2.438,0.406 10 false Torque Sensor (Electric Power Steering Column Sub-assembly) 4.625,0.729 5.073,0.948 0.448,0.219 10 false TRQ1 4.438,0.667 4.552,0.854 0.115,0.188 10 false 7 4.438,1.073 4.573,1.26 0.135,0.188 10 false 2 4.438,1.51 4.573,1.698 0.135,0.188 10 false 3 4.438,1.958 4.552,2.146 0.115,0.188 10 false 5 4.438,2.375 4.552,2.563 0.115,0.188 10 false 1 4.625,1.594 5.073,1.813 0.448,0.219 10 false TRQV 4.625,2.042 5.073,2.26 0.448,0.219 10 false TRQF 4.625,1.146 5.073,1.365 0.448,0.219 10 false TRQ2 4.625,2.469 5.073,2.688 0.448,0.219 10 false TRQG 4.448,2.896 4.688,3.073 0.24,0.177 10 false a

CAUTION / NOTICE / HINT

NOTICE:

If the power steering ECU assembly has been replaced, perform assist map writing.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION


PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION
a.

Check the connection condition of the torque sensor connector.

OK:

Torque sensor connector is securely connected to the power steering ECU assembly.



Result:
Proceed to
OK
NG



OK

2.CHECK POWER STEERING ECU ASSEMBLY (TRQV, TRQF VOLTAGE)

NG

CONNECT CONNECTOR

2.CHECK POWER STEERING ECU ASSEMBLY (TRQV, TRQF VOLTAGE)
a.
C238944
1.167,1.229 1.531,1.469 0.365,0.24 2.125,2.615 1.448,2.021 false 1.667,2.833 1.438,2.104 false 1.302,2.021 1.083,2.802 false 0.094,0.052 0.542,0.344 0.448,0.292 10 *a 1.938,2.646 2.5,2.979 0.563,0.333 10 TRQG 1.313,1.271 1.615,1.688 0.302,0.417 10 a 0.844,2.854 1.698,3.24 0.854,0.385 10 TRQV 1.458,2.854 2.115,3.24 0.656,0.385 10 TRQF
*a Component with harness connected
(Power Steering ECU Assembly)


Turn the ignition switch ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
a-3 (TRQV) - a-1 (TRQG) Ignition switch ON 8.5 to 10.5 V
a-5 (TRQF) - a-1 (TRQG) Ignition switch ON 3.35 to 3.37 V



Result:
Proceed to
OK
NG



OK

3.CHECK POWER STEERING ECU ASSEMBLY (TRQ1, TRQ2 VOLTAGE)

NG

REPLACE POWER STEERING ECU ASSEMBLY

3.CHECK POWER STEERING ECU ASSEMBLY (TRQ1, TRQ2 VOLTAGE)
a.
C238944
1.167,1.229 1.531,1.469 0.365,0.24 2.125,2.615 1.448,2.021 false 1.677,2.823 1.385,2.01 false 1.302,2.104 1.083,2.802 false 0.094,0.052 0.708,0.573 0.615,0.521 10 *a 1.938,2.646 2.563,2.969 0.625,0.323 10 TRQG 1.313,1.281 1.563,1.74 0.25,0.458 10 a 0.844,2.813 1.563,3.25 0.719,0.438 10 TRQ1 1.458,2.854 2.115,3.229 0.656,0.375 10 TRQ2
*a Component with harness connected
(Power Steering ECU Assembly)


Start the engine.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
a-7 (TRQ1) - a-1 (TRQG) Engine running and steering wheel not being turned (without load) 2.3 to 2.7 V
a-2 (TRQ2) - a-1 (TRQG) Engine running and steering wheel not being turned (without load) 2.3 to 2.7 V
a-7 (TRQ1) - a-1 (TRQG) Engine running and steering wheel being turned to the right with vehicle stopped 2.5 to 4.7 V
a-7 (TRQ1) - a-1 (TRQG) Engine running and steering wheel being turned to the left with vehicle stopped 0.3 to 2.5 V
a-2 (TRQ2) - a-1 (TRQG) Engine running and steering wheel being turned to the right with vehicle stopped 0.3 to 2.5 V
a-2 (TRQ2) - a-1 (TRQG) Engine running and steering wheel being turned to the left with vehicle stopped 2.5 to 4.7 V



c.

Under each condition, measure the voltage according to the value(s) in the table blow, and calculate the sum.

Standard Voltage:
Tester Connection Condition Specified Condition
Sum of voltage between a-7 (TRQ1) and a-1 (TRQG) and voltage between a-2 (TRQ2) and a-1 (TRQG) Engine running and steering wheel not being turned (without load) Between 4.85 V and 5.35 V
Engine running and steering wheel being turned to the right with vehicle stopped
Engine running and steering wheel being turned to the left with vehicle stopped



Result:
Proceed to
OK
NG



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPLACE ELECTRIC POWER STEERING COLUMN SUB-ASSEMBLY