Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows)
RM3160E _59 Vehicle Exterior _019717 WINDOW / GLASS _0106113 POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows) J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows)  All Power Windows do not Operate with Driver Side Door Key Cylinder or Wireless Transmitter  


DESCRIPTION

Wireless Transmitter-linked Function
·

w/ Smart Entry and Start System:

When a key switch is pushed: 1) the door control receiver receives the wireless door lock signal; 2) the door control receiver sends a signal to the main body ECU (multiplex network body ECU) through the certification ECU (smart key ECU assembly); 3) the main body ECU (multiplex network body ECU) sends the operation permission signal to the power window regulator motor assemblies; and 4) the power window regulator motor assemblies are activated.

·

w/o Smart Entry and Start System:

When a key switch is pushed: 1) the door control receiver receives the wireless door lock signal; 2) the door control receiver sends a signal to the main body ECU (multiplex network body ECU); 3) the main body ECU (multiplex network body ECU) sends the operation permission signal to the power window regulator motor assemblies; and 4) the power window regulator motor assemblies are activated.


Key-linked Function

When the driver door key cylinder (key linked switch) is turned: 1) the door lock motor receives the signal; 2) the main body ECU (multiplex network body ECU) sends the signal to the power window regulator motor assemblies; and 3) the power window regulator motor assemblies are activated.


CAUTION / NOTICE / HINT

NOTICE:
·

These functions are set through the customize setting, as they are off by default.

·

The power window control system uses the LIN communication system and CAN communication system. Inspect the communication functions by following How to Proceed with Troubleshooting. Troubleshoot the power window control system after confirming that the communication systems are functioning properly.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows)>HOW TO PROCEED WITH TROUBLESHOOTING

·

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.*

*: w/ Smart Entry and Start System

·

As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

*: for LHD



PROCEDURE

1.CHECK BASIC FUNCTION (WIRELESS AND POWER DOOR LOCK CONTROL SYSTEM)
a.

Check that the wireless door lock / unlock function operates normally.

w/ Smart Entry and Start System: Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Smart Entry and Start System)>OPERATION CHECK

w/o Smart Entry and Start System: Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Smart Entry and Start System)>OPERATION CHECK


b.

Check that the key-linked lock / unlock function operates normally.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK


Result:
Result Proceed to
Wireless door lock / unlock function and key-linked lock/unlock function operate normally A
Wireless door lock / unlock function does not operate normally B
Key-linked lock / unlock function does not operate normally C



A

2.CHECK MANUAL UP / DOWN FUNCTION

B

GO TO WIRELESS DOOR LOCK CONTROL SYSTEM (Proceed to Problem Symptoms Table)

C

GO TO POWER DOOR LOCK CONTROL SYSTEM (Proceed to Problem Symptoms Table)

2.CHECK MANUAL UP / DOWN FUNCTION
a.

Check that the manual up and down functions using the power window regulator master switch assembly and power window regulator switch assembly can operate all the power windows.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows)>OPERATION CHECK

OK:

Manual up and down functions are normal.



Result:
Proceed to
OK
NG



OK

3.CHECK REMOTE UP / DOWN FUNCTION

NG

3.CHECK REMOTE UP / DOWN FUNCTION
a.

Check that the remote up and down functions using the power window regulator master switch assembly can operate all the power windows.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows)>OPERATION CHECK

OK:

Remote up and down functions are normal.



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG