The navigation receiver assembly and television display assembly are connected by the AVC-LAN communication line.
This DTC is stored when an AVC-LAN communication error occurs between the navigation receiver assembly and television display assembly.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B15D5 | Rear Seat Entertainment System Disconnected | When either condition below is met:
·
The television display assembly is/was not connected while the engine switch is/was on (IG) or on (ACC) ·
Communication between the master unit and the television display assembly is not possible when the engine is started |
·
Television display assembly power source circuit ·
AVC-LAN circuit between master unit and television display assembly ·
Television display assembly ·
Navigation receiver assembly ·
Harness or connector |
The navigation receiver assembly is the master unit.
Inspect the fuses for circuits related to this system before performing the following procedure.
Check that optional components (including associated wiring) which generate radio waves are not installed.
| Result | Proceed to |
|---|---|
| Optional components (including associated wiring) are installed. | A |
| Optional components (including associated wiring) are not installed. | B |
Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.
This DTC may be stored when an AVC-LAN communication error occurs due to electrical noise.
A
B
Remove optional components (including associated wiring).
Do not remove optional components or associated wiring without the permission of the customer.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR SEAT ENTERTAINMENT SYSTEM>DTC CHECK / CLEAR
Recheck for DTCs and check that no DTCs are output.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the S8 television display assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S8-17 (GND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S8-1 (+B) - S8-17 (GND) | Always | 11 to 14 V |
| S8-2 (ACC) - S8-17 (GND) | Engine switch on (ACC) | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F118 navigation receiver assembly connector.
Disconnect the S8 television display assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S8-3 (TX1+) - F118-9 (TX+) | Always | Below 1 Ω |
| S8-4 (TX1-) - F118-10 (TX-) | Always | Below 1 Ω |
| S8-3 (TX1+) - Body ground | Always | 10 kΩ or higher |
| S8-4 (TX1-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the television display assembly with a new or known good one.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>TELEVISION DISPLAY>REMOVAL
Clear the DTCs.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR SEAT ENTERTAINMENT SYSTEM>DTC CHECK / CLEAR
Recheck for DTCs and check that no DTCs are output.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG