Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM
RM3160E _58 Vehicle Interior _019706 THEFT DETERRENT / KEYLESS ENTRY _0101096 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Horn Circuit  


DESCRIPTION

When the theft deterrent system is switched from the armed state to the alarm sounding state, the main body ECU (multiplex network body ECU) transmits a signal to cause the horns to sound at intervals of 0.4 seconds.

WIRING DIAGRAM

B332839E28
4.625,0.729 4.948,1 0.323,0.271 10 false 29 5.948,0.844 6.198,1.083 0.25,0.24 10 false 28 4.625,1.24 4.938,1.479 0.313,0.24 10 false 21 1.094,1.104 1.74,1.406 0.646,0.302 10 false HORN 2.333,1.885 2.927,2.156 0.594,0.271 10 false HORN 2.958,0.844 3.313,1.167 0.354,0.323 10 false 2 2.042,1.438 2.365,1.698 0.323,0.26 10 false 5 2.031,0.844 2.427,1.208 0.396,0.365 10 false 1 2.938,1.438 3.229,1.719 0.292,0.281 10 false 3 6.229,0.958 6.792,1.229 0.563,0.271 10 false HORN 5.479,3.24 7.125,3.698 1.646,0.458 10 false Main Body ECU (Multiplex Network Body ECU) 4.802,4 6.99,4.365 2.188,0.365 10 false to Steering Pad Switch Assembly 4.531,1.938 6.167,2.344 1.635,0.406 10 false Instrument Panel Junction Block Assembly 1.042,2.281 3.292,2.729 2.25,0.448 10 false No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly 2.573,4.563 2.906,4.844 0.333,0.281 10 false A1 4.167,4.552 4.521,4.813 0.354,0.26 10 false A2 2.281,4.5 2.375,4.635 0.094,0.135 10 false 1 3.885,4.5 3.979,4.635 0.094,0.135 10 false 1 2.573,4.729 3.667,5.188 1.094,0.458 10 false Low Pitched Horn Assembly 4.167,4.729 5.313,5.177 1.146,0.448 10 false High Pitched Horn Assembly 0.802,0.135 1.833,0.542 1.031,0.406 10 false from Battery 4.625,0.938 5,1.229 0.375,0.292 10 false 4F 4.625,1.448 5.021,1.729 0.396,0.281 10 false 4D 5.479,3.083 5.906,3.417 0.427,0.333 10 false MB

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.*

*: w/ Smart Entry and Start System


·

As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

*: for LHD




PROCEDURE

1.INSPECT HORNS
a.

Press the horn switch and check that the horns sound.

Result:
Result Proceed to
Horns sound A
Horns do not sound B




A

2.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

B

2.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the main body ECU (multiplex network body ECU).

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL

B357835C01
3.333,0.083 3.75,0.344 0.417,0.26 3.302,1.594 3.719,1.854 0.417,0.26 5.313,2.615 5.479,2.615 5.479,2.615 5.479,2.281 true 3.458,0.115 3.771,0.313 0.313,0.198 10 false 4F 0.25,0.167 0.563,0.365 0.313,0.198 10 false *a 4.844,2.531 5.292,2.729 0.448,0.198 10 false HORN 3.406,1.635 3.719,1.833 0.313,0.198 10 false MB
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -



b.

Disconnect the 4F instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4F-29 - MB-28 (HORN) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY