Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM
RM3160E _58 Vehicle Interior _019706 THEFT DETERRENT / KEYLESS ENTRY _0101096 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Security Horn Circuit  


DESCRIPTION

When the theft deterrent system is switched from the armed state to the alarm sounding state, the main body ECU (multiplex network body ECU) transmits a signal to cause the security horn assembly to sound at intervals of 0.4 seconds.

WIRING DIAGRAM

B332840E11
2.188,0.958 2.448,1.219 0.26,0.26 10 false 1 3.115,1.604 3.375,1.854 0.26,0.25 10 false 3 3.125,0.948 3.479,1.25 0.354,0.302 10 false 2 2.198,1.604 2.542,1.938 0.344,0.333 10 false 5 5.781,0.958 6.26,1.302 0.479,0.344 10 false 29 4.594,0.854 5.031,1.198 0.438,0.344 10 false 31 1.073,1.24 1.906,1.708 0.833,0.469 10 false S-HORN 2.438,2.063 3.281,2.406 0.844,0.344 10 false S-HORN 6.083,1.094 6.604,1.5 0.521,0.406 10 false SH 4.583,1.063 5.073,1.406 0.49,0.344 10 false 4F 5.781,3.49 6.927,4.031 1.146,0.542 10 false Main Body ECU (Multiplex Network Body ECU) 1.24,2.604 3.49,3.125 2.25,0.521 10 false No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly 4.896,1.688 5.948,2.24 1.052,0.552 10 false Instrument Panel Junction Block Assembly 3.958,4.146 4.5,4.51 0.542,0.365 10 false 1 4.333,4.229 4.781,4.563 0.448,0.333 10 false A36 4.333,4.385 5.198,4.917 0.865,0.531 10 false Security Horn Assembly 0.771,3.865 1.896,4.25 1.125,0.385 10 false from Battery 5.781,3.313 6.156,3.625 0.375,0.313 10 false MB

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.*

*: w/ Smart Entry and Start System


·

As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

*: for LHD




PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (SECURITY HORN)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Security Horn Security horn assembly OFF/ON -
Body Electrical > Main Body > Active Test
Tester Display
Security Horn
50004 123 20
OK:

The security horn assembly sounds and stops correctly when operated through the GTS.



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

2.INSPECT SECURITY HORN ASSEMBLY
2.INSPECT SECURITY HORN ASSEMBLY


Result:
Proceed to
OK
NG



OK

3.INSPECT S-HORN RELAY

NG

3.INSPECT S-HORN RELAY
a.
B256934C02
2.198,0.917 2.198,0.5 2.198,0.5 2.031,0.5 true 2.031,1.885 2.198,1.885 2.198,1.885 2.198,1.469 true 2.646,1.885 2.479,1.885 2.479,1.885 2.479,1.365 true 2.823,1 2.823,0.5 2.823,0.5 2.656,0.5 true 0.104,0.083 0.417,0.396 0.313,0.313 10 false *1 0.323,1.458 0.573,1.75 0.25,0.292 10 false 5 1.313,0.667 1.594,0.917 0.281,0.25 10 false 2 0.313,0.667 0.51,0.906 0.198,0.24 10 false 1 1.313,1.469 1.563,1.708 0.25,0.24 10 false 3 2.708,1.792 2.927,2.01 0.219,0.219 10 false 5 1.833,1.771 2.063,2 0.229,0.229 10 false 1 1.917,0.417 2.208,0.688 0.292,0.271 10 false 2 2.542,0.417 2.813,0.708 0.271,0.292 10 false 3
*1 S-HORN Relay


Remove the S-HORN relay from the No. 1 engine room relay block and No. 1 junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage not applied between terminals 1 and 2 10 kΩ or higher
3 - 5 Battery voltage applied between terminals 1 and 2 Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPLACE S-HORN RELAY

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the main body ECU (multiplex network body ECU).

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL

B357835C02
3.396,0.198 3.74,0.406 0.344,0.208 3.292,1.646 3.635,1.854 0.344,0.208 5.396,2.646 5.646,2.646 5.646,2.646 5.646,2.302 true 3.49,0.219 3.802,0.417 0.313,0.198 10 false 4F 5.167,2.563 5.479,2.76 0.313,0.198 10 false SH 0.208,0.156 0.552,0.469 0.344,0.313 10 false *a 3.365,1.667 3.677,1.865 0.313,0.198 10 false MB
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -



b.

Disconnect the 4F instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4F-31 - MB-29 (SH) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (BATTERY - S-HORN RELAY)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (BATTERY - S-HORN RELAY)
a.
B340809C03
0.146,0.125 0.458,0.281 0.313,0.156 10 false *1
*1 No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
No. 1 engine room relay block and No. 1 junction block assembly S-HORN relay terminal 1 - Body ground Always 11 to 14 V
No. 1 engine room relay block and No. 1 junction block assembly S-HORN relay terminal 5 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (S-HORN RELAY - SECURITY HORN ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (S-HORN RELAY - SECURITY HORN ASSEMBLY)
a.
B340809C03
0.146,0.125 0.458,0.281 0.313,0.156 10 false *1
*1 No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
No. 1 engine room relay block and No. 1 junction block assembly S-HORN relay terminal 3 - A36-1 Always Below 1 Ω
No. 1 engine room relay block and No. 1 junction block assembly S-HORN relay terminal 3 or A36-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (S-HORN RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (S-HORN RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.
B340809C03
0.146,0.125 0.458,0.281 0.313,0.156 10 false *1
*1 No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
No. 1 engine room relay block and No. 1 junction block assembly S-HORN relay terminal 2 - 4F-31 Always Below 1 Ω
No. 1 engine room relay block and No. 1 junction block assembly S-HORN relay terminal 2 or 4F-31 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR