Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM
RM3160E _58 Vehicle Interior _019706 THEFT DETERRENT / KEYLESS ENTRY _0101096 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Unlock Warning Switch Circuit  


DESCRIPTION

The unlock warning switch assembly comes on when the key is inserted into the ignition key cylinder and goes off when the key is removed.

WIRING DIAGRAM

B357836
1.594,1.031 1.938,1.25 0.344,0.219 10 false F52 1.604,1.198 3.073,1.552 1.469,0.354 10 false Unlock Warning Switch Assembly 1.823,0.594 2.094,0.813 0.271,0.219 10 false 2 2.719,0.583 2.99,0.802 0.271,0.219 10 false 1 3.875,0.708 4.229,0.969 0.354,0.26 10 false 4D 3.875,0.49 4.229,0.75 0.354,0.26 10 false 28 5.292,0.583 5.563,0.802 0.271,0.219 10 false 3 5.5,0.708 6.031,0.958 0.531,0.25 10 false KSW 4.302,1.177 5.385,1.74 1.083,0.563 10 false Instrument Panel Junction Block Assembly 5.438,2.813 6.594,3.354 1.156,0.542 10 false Main Body ECU (Multiplex Network Body ECU) 5.438,2.646 5.792,2.906 0.354,0.26 10 false MB

CAUTION / NOTICE / HINT

NOTICE:
·

As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

*: for LHD




PROCEDURE

1.READ VALUE USING GTS (KEY UNLOCK WARNING SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Key Unlock Warning SW Unlock warning switch ON or OFF ON: Key inserted into ignition key cylinder
OFF: Key removed from ignition key cylinder
-
Body Electrical > Main Body > Data List
Tester Display
Key Unlock Warning SW
50003 123 32
OK:

The GTS display changes correctly in response to the unlock warning switch assembly status.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT UNLOCK WARNING SWITCH ASSEMBLY
2.INSPECT UNLOCK WARNING SWITCH ASSEMBLY
a.

Remove the unlock warning switch assembly.

Click hereVehicle Interior>DOOR LOCK>UNLOCK WARNING SWITCH>REMOVAL


b.

Inspect the unlock warning switch assembly.

Click hereVehicle Interior>DOOR LOCK>UNLOCK WARNING SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPLACE UNLOCK WARNING SWITCH ASSEMBLY

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the main body ECU (multiplex network body ECU).

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL

B357837
3.354,0.094 3.729,0.323 0.375,0.229 3.281,1.615 3.656,1.844 0.375,0.229 1.583,2.635 1.333,2.635 1.333,2.635 1.333,2.302 true 0.302,0.177 0.677,0.448 0.375,0.271 10 false *a 3.458,0.125 3.833,0.396 0.375,0.271 10 false 4D 3.365,1.646 3.74,1.917 0.375,0.271 10 false MB 1.646,2.552 2.073,2.75 0.427,0.198 10 false KSW
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -



b.

Disconnect the 4D instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4D-28 - MB-3 (KSW) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - UNLOCK WARNING SWITCH ASSEMBLY - BODY GROUND)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - UNLOCK WARNING SWITCH ASSEMBLY - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4D-28 - F52-1 Always Below 1 Ω
4D-28 or F52-1 - Body ground Always 10 kΩ or higher
F52-2 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR