Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM3160E _54 Brake _019692 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0106374 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1436  Yaw Rate Sensor Malfunction  


DESCRIPTION

This DTC is stored when the skid control ECU (brake actuator assembly) detects improper installation of the yaw rate and acceleration sensor (airbag sensor assembly) or an abnormality in the difference between the yaw rate sensor value and the control value estimated based on the acceleration sensor, steering angle sensor and speed sensor signals.

The airbag sensor assembly has a built-in yaw rate and acceleration sensor and detects the vehicle condition.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1436 Yaw Rate Sensor Malfunction Either of the following is detected:
1.

With the vehicle stationary, the yaw rate sensor output value is not 0°/s.

2.

Yaw rate sensor stuck malfunction.


·

Sensor installation

·

Yaw rate sensor (airbag sensor assembly)



CAUTION / NOTICE / HINT

NOTICE:

When replacing the yaw rate and acceleration sensor (airbag sensor assembly), perform zero point calibration and store system information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION


PROCEDURE

1.READ VALUE USING GTS (YAW RATE AND ACCELERATION SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Select the Data List using the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Yaw Rate Sensor Yaw rate sensor Min.: -128°/s, Max.: 127°/s Vehicle stopped: 0°/s
Turning right: -128 to 0°/s
Turning left: 0 to 127°/s
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
Yaw Rate Sensor
50003 105 24

d.

Check the yaw rate and acceleration sensor (airbag sensor assembly) output value displayed on the GTS.

Result:
Result Proceed to
NG (The yaw rate and acceleration sensor (airbag sensor assembly) output value is 0°/s when the vehicle is stationary, but the value fluctuates when turning.) A
NG (The yaw rate and acceleration sensor (airbag sensor assembly) output value is not 0°/s when the vehicle is stationary.) B
OK C


NOTICE:

Check the yaw rate and acceleration sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE




A

2.CHECK AIRBAG SENSOR ASSEMBLY INSTALLATION

B

C

2.CHECK AIRBAG SENSOR ASSEMBLY INSTALLATION
a.

Turn the ignition switch off.


b.

Check that the yaw rate and acceleration sensor (airbag sensor assembly) has been installed properly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>INSTALLATION

OK:

The sensor is tightened to the specified torque.

The sensor is not installed in a tilted position.


NOTICE:

Check the yaw rate and acceleration sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

NG