Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2013.12–2016.11
RM3160E _54 Brake _019692 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0106374 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1421  Open or Short in Master Cylinder Pressure Sensor  C1423  Master Cylinder Pressure Sensor Zero Point Low Malfunction  C1424  Master Cylinder Pressure Sensor Output Malfunction  C1449  Master Cylinder Output Value Malfunction  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area
C1421 Open or Short in Master Cylinder Pressure Sensor When the IG1 terminal voltage is 9.5 V or more, the PMC terminal voltage is not between 0.26 and 4.47 V for 0.1 seconds or more. Master cylinder pressure sensor (brake actuator assembly)
C1423 Master Cylinder Pressure Sensor Zero Point Low Malfunction The PMC terminal voltage is less than 0.26 V for 5 seconds or more. Master cylinder pressure sensor (brake actuator assembly)
C1424 Master Cylinder Pressure Sensor Output Malfunction Any of the following is detected:
1.

At a vehicle speed of 10 km/h (6 mph) or more, noise occurs in the PMC terminal signal 7 times or more within 5 seconds.

2.

When the vehicle speed drops from 40 km/h (25 mph) to 0 km/h (0 mph), the master cylinder pressure does not change by at least 0.048 MPa (0.5 kgf/cm2, 7 psi) 5 times or more.

3.

At a vehicle speed of 7 km/h (4 mph) or more, the PMC terminal voltage is between 0.86 and 1.0 V and the master cylinder pressure does not change by at least 0.048 MPa (0.5 kgf/cm2, 7 psi) for 60 seconds or more.

4.

At a vehicle speed of 7 km/h (4 mph) or more, the PMC terminal voltage is 1.0 V or more and the master cylinder pressure does not change by at least 0.048 MPa (0.5 kgf/cm2, 7 psi) for 30 seconds or more.

5.

At a vehicle speed of 7 km/h or more, the condition that the master cylinder pressure sensor input value is excessively larger than the estimated master cylinder pressure based on the vehicle deceleration speed for 1 second when braking (stop light switch assembly ON) occurs 5 times or more after turning the ignition switch to ON, and this recurs 8 times in a successive manner.


Master cylinder pressure sensor (brake actuator assembly)
C1449 Master Cylinder Output Value Malfunction The master cylinder pressure sensor is in an invalid state for 0.2 seconds or more when the voltage at terminal IG1 is 8.4 V or higher. Master cylinder pressure sensor (brake actuator assembly)

HINT:

for C1423 and C1424: Even after the trouble areas are repaired, the ABS warning light will not go off unless the following operations are performed:

1.

Turn the ignition switch to ON.

2.

Keep the vehicle stationary for 5 seconds or more and depress the brake pedal lightly 2 or 3 times.

3.

Drive the vehicle at the vehicle speed of 50 km/h (31 mph) and depress and hold the brake pedal firmly for approximately 3 seconds.

4.

Repeat the above operation 3 times or more and check that the ABS warning light goes off.

5.

Clear the DTCs.



CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION


PROCEDURE

1.REPLACE BRAKE ACTUATOR ASSEMBLY
a.

Replace the master cylinder pressure sensor (brake actuator assembly).

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR>REMOVAL


b.

Perform zero point calibration of the yaw rate and acceleration sensor and store system information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION

Chassis > ABS/VSC/TRC > Utility
Tester Display
Test Mode
50005 105 166

c.

Perform the sensor check in Test Mode Procedure.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE

Chassis > ABS/VSC/TRC > Utility
Tester Display
Signal Check
50005 105 3

Result:
Proceed to
NEXT



NEXT

END