These solenoids turn on when signals are received from the skid control ECU (brake actuator assembly) and they control the pressure acting on the wheel cylinders to control the braking force.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1225 | SM Solenoid Circuit | Any of the following is detected:
1.
While switching solenoid (SM1, SM2, SFR, SFL, SRR or SRL) is on, overcurrent continues for 0.1 seconds or more. 2.
While switching solenoid (SM1, SM2, SFR, SFL, SRR or SRL) is off, an open circuit continues for 0.05 seconds or more. 3.
While switching solenoid (SM1, SM2, SFR, SFL, SRR or SRL) is on, an open circuit continues for 0.05 seconds or more. 4.
While switching solenoid (SM1, SM2, SFR, SFL, SRR or SRL) is off, current continues to be applied for 0.05 seconds or more. 5.
A condition in which the outputs from switching solenoids (SM1, SM2, SFR, SFL, SRR and SRL) are different continues for 0.2 seconds or more. |
·
Solenoid circuit ·
Solenoid valve (brake actuator assembly) |
| C1468 | SFR Solenoid Circuit | Open or short in the solenoid circuit continues for 0.05 seconds or more. | ·
Solenoid circuit ·
Solenoid valve (brake actuator assembly) |
| C1469 | SFL Solenoid Circuit | Open or short in the solenoid circuit continues for 0.05 seconds or more. | ·
Solenoid circuit ·
Solenoid valve (brake actuator assembly) |
| C146A | SRR Solenoid Circuit | Open or short in the solenoid circuit continues for 0.05 seconds or more. | ·
Solenoid circuit ·
Solenoid valve (brake actuator assembly) |
| C146B | SRL Solenoid Circuit | Open or short in the solenoid circuit continues for 0.05 seconds or more. | ·
Solenoid circuit ·
Solenoid valve (brake actuator assembly) |
When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION
These codes are detected when a problem is determined in the skid control ECU (brake actuator assembly).
The solenoid circuits are in the brake actuator assembly.
Therefore, solenoid circuit inspection and solenoid unit inspection cannot be performed. Be sure to check if any DTCs are output before replacing the skid control ECU (brake actuator assembly).
Clear the DTCs.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Start the engine.
Perform a road test.
Check if the same DTC is output.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTCs C1225, C1468, C1469, C146A and C146B are not output. | A |
| DTCs C1225, C1468, C1469, C146A and/or C146B are output. | B |
The skid control ECU (brake actuator assembly) performs self diagnosis of the solenoid circuit after the ignition switch is turned to ON.
If the normal system code is output (no DTCs are output), slightly jiggle the connectors, wire harness, and fuses of the skid control ECU (brake actuator assembly).
If any DTCs are output while jiggling a connector or wire harness of the skid control ECU (brake actuator assembly), inspect and repair the connector or wire harness.
If no DTCs were output when reconfirming DTCs, checking for intermittent problems is necessary because it is suspected that the original DTCs were stored due to the poor connection of a connector terminal.
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B