Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2013.12–2016.11
RM3160E _54 Brake _019692 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0106374 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1379  Downhill Assist Control Switch Malfunction (Test Mode DTC)  


DESCRIPTION

DTC C1379 will be deleted when the downhill assist control switch sends a downhill assist control operation signal or when Test Mode ends. DTC C1379 is output only in Test Mode.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1379 Downhill Assist Control Switch Malfunction (Test Mode DTC) Detected only during Test Mode. Downhill assist control switch

WIRING DIAGRAM

C296143E01
2.917,2.635 5.385,3.125 2.469,0.49 10 false Downhill Assist Control Switch 2.563,2.635 2.875,2.833 0.313,0.198 10 false F41 5.521,3.906 5.833,4.104 0.313,0.198 10 false A47 5.521,4.083 7.156,4.594 1.635,0.51 10 false Skid Control ECU (Brake Actuator Assembly) 3.167,2.188 3.479,2.385 0.313,0.198 10 false E 3.896,2.188 4.208,2.385 0.313,0.198 10 false B 2.99,1.979 3.302,2.177 0.313,0.198 10 false 1 4.094,1.979 4.406,2.177 0.313,0.198 10 false 4 5.698,1.969 6.01,2.167 0.313,0.198 10 false 29 5.958,2.083 6.552,2.354 0.594,0.271 10 false HDCS

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION


PROCEDURE

1.READ VALUE USING GTS (DOWNHILL ASSIST CONTROL SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Select the Data List using the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Downhill Assist Control SW Downhill assist control switch ON or OFF ON: Switch on
OFF: Switch off
for AWD
Chassis > ABS/VSC/TRC > Data List
Tester Display
Downhill Assist Control SW
50003 105 260

d.

Using the GTS, check the switch condition on the GTS changes according to downhill assist control switch operation.

OK:

The GTS displays ON or OFF according to downhill assist control switch operation.



Result:
Result
OK
NG



OK

2.PERFORM TEST MODE INSPECTION (SIGNAL CHECK)

NG

3.INSPECT DOWNHILL ASSIST CONTROL SWITCH
2.PERFORM TEST MODE INSPECTION (SIGNAL CHECK)
a.

Perform the sensor check in Test Mode Procedure.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE

Chassis > ABS/VSC/TRC > Utility
Tester Display
Signal Check
50005 105 3
OK:

All Test Mode DTCs are cleared.


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

NG

3.INSPECT DOWNHILL ASSIST CONTROL SWITCH
a.
C296498C01
1.542,1.594 1.833,0.833 false 1.833,2.75 1.531,1.938 false 0.229,0.271 0.542,0.469 0.313,0.198 10 false *a 1.833,0.656 2.146,0.854 0.313,0.198 10 false B 1.823,2.792 2.135,2.99 0.313,0.198 10 false E
*a Component without harness connected
(Downhill Assist Control Switch))


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the F41 downhill assist control switch connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (B) - 1 (E) Switch is pushed in Below 1 Ω
4 (B) - 1 (E) Switch is not pushed in 10 kΩ or higher


NOTICE:

Check the downhill assist control switch signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - DOWNHILL ASSIST CONTROL SWITCH)

NG

4.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - DOWNHILL ASSIST CONTROL SWITCH)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the A47 skid control ECU (brake actuator assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A47-29 (HDCS) - F41-4 (B) Always Below 1 Ω
A47-29 (HDCS) or F41-4 (B) - Body ground Always 10 kΩ or higher
F41-1 (E) - Body ground Always Below 1 Ω


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR