Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › CAMSHAFT POSITION SENSOR › 2013.12–2016.11
RM3160E _51 Engine / Hybrid System _019662 2GR-FE ENGINE CONTROL _0106868 CAMSHAFT POSITION SENSOR A

2GR-FE ENGINE CONTROL  CAMSHAFT POSITION SENSOR  INSTALLATION  


PROCEDURE

Hide 11401M 1.INSTALL CAMSHAFT POSITION SENSOR (for Exhaust Side of Bank 2)

a.
A231950C03
1.708,0.51 1.427,0.198 1.427,0.198 1.167,0.198 false 0.979,0.115 1.292,0.313 0.313,0.198 10 false *a
*a O-ring


Apply a light coat of engine oil to the O-ring of the camshaft position sensor.


b.

Install the camshaft position sensor to the cylinder head cover sub-assembly LH with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:
·

If the camshaft position sensor has been struck or dropped, replace it.

·

Make sure that the O-ring is not cracked or does not move out of place during installation.




c.

Connect the camshaft position sensor connector.


Hide 11401M 2.INSTALL CAMSHAFT POSITION SENSOR (for Intake Side of Bank 2)

a.
A231950C03
1.708,0.51 1.427,0.198 1.427,0.198 1.167,0.198 false 0.979,0.115 1.292,0.313 0.313,0.198 10 false *a
*a O-ring


Apply a light coat of engine oil to the O-ring of the camshaft position sensor.


b.

Install the camshaft position sensor to the cylinder head cover sub-assembly LH with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:
·

If the camshaft position sensor has been struck or dropped, replace it.

·

Make sure that the O-ring is not cracked or does not move out of place during installation.




c.

Connect the camshaft position sensor connector.


Hide 11401M 3.INSTALL CAMSHAFT POSITION SENSOR (for Exhaust Side of Bank 1)

a.
A231950C03
1.708,0.51 1.427,0.198 1.427,0.198 1.167,0.198 false 0.979,0.115 1.292,0.313 0.313,0.198 10 false *a
*a O-ring


Apply a light coat of engine oil to the O-ring of the camshaft position sensor.


b.

Install the camshaft position sensor to the cylinder head cover sub-assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:
·

If the camshaft position sensor has been struck or dropped, replace it.

·

Make sure that the O-ring is not cracked or does not move out of place during installation.




c.

Connect the camshaft position sensor connector.


Hide 11401M 4.INSTALL CAMSHAFT POSITION SENSOR (for Intake Side of Bank 1)

a.
A231950C03
1.708,0.51 1.427,0.198 1.427,0.198 1.167,0.198 false 0.979,0.115 1.292,0.313 0.313,0.198 10 false *a
*a O-ring


Apply a light coat of engine oil to the O-ring of the camshaft position sensor.


b.

Install the camshaft position sensor to the cylinder head cover sub-assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:
·

If the camshaft position sensor has been struck or dropped, replace it.

·

Make sure that the O-ring is not cracked or does not move out of place during installation.




c.

Connect the camshaft position sensor connector.


Hide 17190 5.INSTALL INTAKE AIR SURGE TANK ASSEMBLY