Home › Engine / Hybrid System › 2GR-FE (INTAKE / EXHAUST) › INTAKE MANIFOLD › 2013.12–2016.11
RM3160E _51 Engine / Hybrid System _019666 2GR-FE INTAKE / EXHAUST _0109811 INTAKE MANIFOLD A

2GR-FE INTAKE / EXHAUST  INTAKE MANIFOLD  INSTALLATION  


PROCEDURE

Hide 1.INSTALL STUD BOLT

HINT:

If a stud bolt is deformed or the threads are damaged, replace it.


a.
A316007

Using an E8 "TORX" socket wrench, install the 2 stud bolts to the intake manifold.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 17111 2.INSTALL INTAKE MANIFOLD

a.

Install a new intake manifold to head gasket to each cylinder head sub-assembly.

NOTICE:
·

Align the port holes of the intake manifold to head gaskets and cylinder head sub-assembly.

·

Make sure that the intake manifold to head gaskets are installed in the correct direction.




b.

Temporarily install the intake manifold to the cylinder head sub-assembly with the 6 bolts and 4 nuts.


c.
A316006C01
1.646,1.208 1.823,1.385 0.177,0.177 10 true 1 2.146,0.76 2.313,0.958 0.167,0.198 10 true 2 2.229,0.094 2.427,0.292 0.198,0.198 10 true 3 1.375,1.948 1.531,2.146 0.156,0.198 10 true 4 1.042,0.031 1.24,0.219 0.198,0.188 10 true 5 2.313,1.958 2.469,2.146 0.156,0.188 10 true 6 0.292,0.344 0.458,0.531 0.167,0.188 10 true 7 2.927,0.49 3.125,0.698 0.198,0.208 10 true 8 0.615,1.75 0.781,1.969 0.167,0.219 10 true 9 3.219,1.125 3.417,1.333 0.198,0.208 10 true 10
V100135

Bolt
V100136

Nut


Tighten the 6 bolts and 4 nuts in the order shown in the illustration.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 23807 3.INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY

Hide 23901 4.CONNECT FUEL TUBE SUB-ASSEMBLY

Hide 23292D 5.INSTALL FUEL HOSE PROTECTOR

Hide 12327A 6.INSTALL NO. 2 ENGINE MOUNTING STAY RH (for Intake Manifold Side)

a.

Install the No. 2 engine mounting stay RH to the intake manifold with the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 12327A 7.INSTALL NO. 2 ENGINE MOUNTING STAY RH (for Engine Mounting Stay Side)

Hide 17190 8.INSTALL INTAKE AIR SURGE TANK ASSEMBLY

NOTICE:

Do not apply oil to the bolts and nuts as listed below:

Oil Application Prohibited Bolt and Nut
Bolt and Nut for Intake Air Surge Tank Assembly and Intake Manifold
Bolt for No. 1 Surge Tank Stay and Intake Air Surge Tank Assembly
Bolt for Throttle Body Bracket and Intake Air Surge Tank Assembly


a.

Install 3 new intake air surge tank gaskets to the intake manifold.


b.

Temporarily install the intake air surge tank assembly to the intake manifold with the 4 bolts and 2 nuts.


c.
A316005C02
1.302,1.75 1.427,1.906 0.125,0.156 10 true 1 1.24,0.802 1.365,0.958 0.125,0.156 10 true 2 1.885,0.885 2.01,1.042 0.125,0.156 10 true 3 1.896,1.771 2.021,1.927 0.125,0.156 10 true 4 0.479,1.302 0.604,1.458 0.125,0.156 10 true 5 2.667,1.396 2.792,1.552 0.125,0.156 10 true 6
V100135

Bolt
V100136

Nut


Using a 5 mm hexagon socket wrench, tighten the 4 bolts in the order shown in the illustration.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


d.

Tighten the 2 nuts in the order shown in the illustration.

Torque:
16 N*m (163 kgf*cm, 12 ft.*lbf)


e.

Install the No. 1 surge tank stay to the intake air surge tank assembly with the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


f.

Install the throttle body bracket to the intake air surge tank assembly with the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


g.

Connect the intake air control valve (for ACIS) connector.


h.

Connect the ventilation hose to the intake air surge tank assembly and slide the clip to secure it.


i.

Connect the fuel vapor feed hose to the hose clamp.


j.

Connect the fuel vapor feed hose to the intake air surge tank assembly.


k.

Connect the union to check valve hose to the hose clamp.


l.

Connect the union to check valve hose to the intake air surge tank assembly and slide the clip to secure it.


Hide 22030 9.INSTALL THROTTLE BODY WITH MOTOR ASSEMBLY

Hide 55701J 10.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)

Hide 55701J 11.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)

Hide 12.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 13.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION