Home › Drivetrain › U660E AUTOMATIC TRANSMISSION / TRANSAXLE › PARK / NEUTRAL POSITION SWITCH › 2013.12–2016.11
RM3160E _52 Drivetrain _019725 U660E AUTOMATIC TRANSMISSION / TRANSAXLE _0107322 PARK / NEUTRAL POSITION SWITCH A

U660E AUTOMATIC TRANSMISSION / TRANSAXLE  PARK / NEUTRAL POSITION SWITCH  INSTALLATION  


PROCEDURE

Hide 84540 1.INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY

a.

Move the shift lever to N.


b.
C135733C18
2.532,0.661 2.722,0.821 0.19,0.16 10 *a 1.701,1.332 2.499,0.754 2.499,0.754 1.699,1.456 false
*a Protrusion


Align the protrusions of the park/neutral position switch assembly.


c.

Install the park/neutral position switch assembly to the manual valve lever shaft sub-assembly with the 2 bolts.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

NOTICE:
·

Before installing the park/neutral position switch assembly, remove any dirt or rust on the installation portion of the manual valve lever shaft sub-assembly. Be sure to install the park/neutral position switch assembly straight along the shaft while being careful not to deform the plate spring that supports the shaft. If the plate spring is deformed, the park/neutral position switch assembly cannot be reinstalled correctly.

·

After installing the park/neutral position switch assembly, confirm that the 2 protrusions on the park/neutral position switch assembly are aligned.




d.

Install the transmission control shaft lever to the manual valve lever shaft sub-assembly with the nut and washer.

Torque:
12.7 N*m (130 kgf*cm, 9 ft.*lbf)


e.

Connect the connector to the park/neutral position switch.


Hide 33820B 2.INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY

a.

Install a new clip to the No. 1 transmission control cable bracket.


b.
C102659C02
2.229,1.135 2.76,1.135 true 2.198,0.938 0.438,1.635 0.438,1.635 1.063,0.99 true 2.125,0.625 0.75,0.177 0.75,0.177 1.198,0.635 true 0.563,0.063 0.844,0.313 0.281,0.25 10 false *a 0.271,1.625 0.583,1.885 0.313,0.26 10 false *b 2.771,1.052 3.031,1.313 0.26,0.26 10 false *c
*a Claw A
*b Claw B
*c Transmission Control Cable Assembly


Install the transmission control cable assembly to the No. 1 transmission control cable bracket.

NOTICE:
·

Make sure that the claws A on the clip are securely fit into the No. 1 transmission control cable bracket holes.

·

Make sure that the transmission control cable assembly is securely installed inside of the claws B of the clip.




c.

Install the transmission control cable assembly to the transmission control shaft lever with the nut.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)

NOTICE:

Before connecting the transmission control cable assembly, check that the park/neutral position switch assembly and the shift lever are in neutral.



d.

Engage wire harness clamp to the wire harness clamp bracket.


Hide 17701 3.INSTALL AIR CLEANER CASE SUB-ASSEMBLY

Hide 17801 4.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 17705 5.INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE

Hide 17750A 6.INSTALL INLET AIR CLEANER ASSEMBLY

Hide 53295E 7.INSTALL COOL AIR INTAKE DUCT SEAL

Hide 53298E 8.INSTALL RADIATOR SIDE SEAL RH

Hide 53299D 9.INSTALL RADIATOR SIDE DEFLECTOR SEAL LH

Hide 10.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY OPERATION