Home › Engine / Hybrid System › 2GR-FE ENGINE MECHANICAL › ENGINE ASSEMBLY › 2013.12–2016.11
RM3160E _51 Engine / Hybrid System _019663 2GR-FE ENGINE MECHANICAL _0109582 ENGINE ASSEMBLY A

2GR-FE ENGINE MECHANICAL  ENGINE ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repair" after replacing the engine assembly.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


PROCEDURE

Hide 2.REMOVE ENGINE FROM ENGINE STAND

a.

Using an engine sling device and engine lift, secure the engine assembly.

NOTICE:
·

Pay attention to the angle of the sling device as the engine assembly or No. 1 engine hanger and No. 2 engine hanger may be damaged or deformed if the angle is incorrect.

·

Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.




b.

Remove the engine assembly from the engine stand.


Hide 32101 3.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

Hide 30500 4.INSTALL AUTOMATIC TRANSAXLE ASSEMBLY (for 2WD)

Hide 30500 5.INSTALL AUTOMATIC TRANSAXLE ASSEMBLY (for AWD)

Hide 36118A 6.INSTALL TRANSFER STIFFENER PLATE RH (for AWD)

Hide 82121 9.INSTALL ENGINE WIRE

a.

Install the engine wire to the engine assembly with transaxle.


Hide 12360 11.TEMPORARILY INSTALL FRONT ENGINE MOUNTING INSULATOR ASSEMBLY

HINT:

Perform this procedure only when replacement of the front engine mounting insulator assembly is necessary.


a.

Temporarily install the front engine mounting insulator assembly with the 3 nuts.


Hide 12372A 12.TEMPORARILY INSTALL ENGINE MOUNTING INSULATOR LH

HINT:

Perform this procedure only when replacement of the engine mounting insulator LH is necessary.


a.

Temporarily install the engine mounting insulator LH with the 3 nuts.


Hide 12362 13.TEMPORARILY INSTALL ENGINE MOUNTING INSULATOR RH

HINT:

Perform this procedure only when replacement of the engine mounting insulator RH is necessary.


a.

Temporarily install the engine mounting insulator RH with the 3 nuts.


Hide 12380 14.TEMPORARILY INSTALL REAR ENGINE MOUNTING INSULATOR ASSEMBLY

HINT:

Perform this procedure only when replacement of the rear engine mounting insulator assembly is necessary.


a.

Temporarily install the rear engine mounting insulator with the 2 nuts.


Hide 51100G 15.INSTALL FRONT FRAME ASSEMBLY

a.

Install the engine mounting insulator RH with the nut.

Torque:
95 N*m (969 kgf*cm, 70 ft.*lbf)


b.

Install the engine mounting insulator LH with the nut.

Torque:
95 N*m (969 kgf*cm, 70 ft.*lbf)


c.

Install the front engine mounting insulator assembly with the bolt.

Torque:
87 N*m (887 kgf*cm, 64 ft.*lbf)


d.

Install the rear engine mounting insulator assembly with the 2 bolts.

Torque:
75 N*m (765 kgf*cm, 55 ft.*lbf)


e.

Connect the 2 wire clamps.


f.

Fully tighten the 11 temporarily installed nuts of the engine mounting insulators.

HINT:

Perform this procedure only when replacement of the engine mounting insulators is necessary.


A315943C01
1.615,0.365 1.927,0.521 0.313,0.156 10 false *1 1.74,3.146 2.052,3.302 0.313,0.156 10 false *2 5.083,0.302 5.396,0.458 0.313,0.156 10 false *3 5.375,3.219 5.688,3.375 0.313,0.156 10 false *4 1.042,1.438 1.198,1.635 0.156,0.198 10 true A 1.833,3.979 1.99,4.156 0.156,0.177 10 true B 0.604,1.771 0.76,1.969 0.156,0.198 10 true A 2.063,1.802 2.219,2 0.156,0.198 10 true A 5.802,4.573 5.958,4.771 0.156,0.198 10 true A 4.896,4.552 5.052,4.75 0.156,0.198 10 true A 4.948,1 5.104,1.198 0.156,0.198 10 true B 5.49,1.021 5.646,1.219 0.156,0.198 10 true B 5.729,1.885 5.885,2.063 0.156,0.177 10 true B 1.531,3.656 1.688,3.833 0.156,0.177 10 true B 2.104,3.5 2.26,3.677 0.156,0.177 10 true B
*1 Front Engine Mounting Insulator Assembly *2 Engine Mounting Insulator RH
*3 Engine Mounting Insulator LH *4 Rear Engine Mounting Insulator


Torque:
Nut (A) : 58 N*m (591 kgf*cm, 43 ft.*lbf)

Torque:
Nut (B) : 99 N*m (1010 kgf*cm, 73 ft.*lbf)


g.

Install the 7 hole plugs to the front frame assembly.

HINT:

Perform this procedure only when replacement of the engine mounting insulators is necessary.



Hide 16.INSTALL STEERING LINK ASSEMBLY (for AWD)

Hide 48811 17.INSTALL FRONT STABILIZER BAR (for AWD)

Hide 48829A 18.INSTALL FRONT NO. 1 STABILIZER BRACKET LH (for AWD)

Hide 48824A 19.INSTALL FRONT NO. 1 STABILIZER BRACKET RH (for AWD)

HINT:

Perform the same procedure as for the LH side.


Hide 88310 20.INSTALL COMPRESSOR ASSEMBLY WITH PULLEY

Hide 22.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE

a.

Set the engine assembly with transaxle on the engine lifter.

NOTICE:
·

Using height adjustment attachments and plate lift attachments, place the engine assembly with transaxle horizontally.

·

Do not place any height adjustment attachments or plate lift attachments under the front frame assembly.

·

Servicing an engine assembly while it is hanging is dangerous. This can be done only when installing/removing the engine assembly to/from an engine stand.

·

To prevent the oil pan from deforming, do not place any attachments under the oil pan of the engine assembly with transaxle.





c.

Install the engine assembly with transaxle to the vehicle.

NOTICE:
·

Do not raise the engine assembly with transaxle more than necessary. If the engine assembly with transaxle is raised excessively, the vehicle may also be lifted up.

·

Make sure that the engine assembly with transaxle is clear of all wiring and hoses.

·

While raising the engine assembly with transaxle into the vehicle, do not allow it to contact the vehicle.




d.
A315769C03
0.604,0.281 0.75,0.469 0.146,0.188 10 true B 1.458,1.063 1.594,1.25 0.135,0.188 10 true A 2.115,0.167 2.26,0.354 0.146,0.188 10 true B 1.188,0.156 1.333,0.344 0.146,0.188 10 true B 1.844,1.063 1.979,1.24 0.135,0.177 10 true A 2.667,0.323 2.813,0.51 0.146,0.188 10 true B 0.271,0.969 0.417,1.156 0.146,0.188 10 true A 2.938,0.969 3.083,1.156 0.146,0.188 10 true A 0.552,2.292 0.698,2.479 0.146,0.188 10 true C 1.479,2.375 1.625,2.552 0.146,0.177 10 true B 2.688,2.292 2.833,2.479 0.146,0.188 10 true C 1.771,2.375 1.917,2.542 0.146,0.167 10 true B 0.719,2.979 0.865,3.167 0.146,0.188 10 true D 1.115,3.229 1.26,3.417 0.146,0.188 10 true D 2.177,3.229 2.323,3.417 0.146,0.188 10 true D 2.583,2.979 2.729,3.167 0.146,0.188 10 true D
V100135

Bolt
V100136

Nut


Install the frame side plate RH and frame side plate LH with the 6 bolts and 2 nuts.

Torque:
Bolt (A) : 85 N*m (867 kgf*cm, 63 ft.*lbf)
Bolt (B) and Nut (A) : 32 N*m (326 kgf*cm, 24 ft.*lbf)


e.

Install the front suspension member rear brace RH and front suspension member rear brace LH with the 6 bolts and 2 nuts.

Torque:
Bolt (C) : 85 N*m (867 kgf*cm, 63 ft.*lbf)
Bolt (D) and Nut (B) : 32 N*m (326 kgf*cm, 24 ft.*lbf)

HINT:

Perform "Inspection After Repair" after replacing the engine assembly.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Hide 32101A 23.INSTALL DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT (for 2WD)

Hide 32101A 24.INSTALL DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT (for AWD)

Hide 11361J 25.INSTALL FLYWHEEL HOUSING UNDER COVER

a.

Install the flywheel housing under cover with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 17571 26.INSTALL NO. 1 EXHAUST PIPE SUPPORT BRACKET (for Upper Side)

a.

Install the No. 1 exhaust pipe support bracket with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 88704 27.CONNECT SUCTION HOSE SUB-ASSEMBLY

Hide 88703 28.CONNECT DISCHARGE HOSE SUB-ASSEMBLY

Hide 45220 29.CONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY (for 2WD)

Hide 45220 30.CONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY (for AWD)

Hide 17410 32.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 17584B 33.INSTALL NO. 1 EXHAUST PIPE SUPPORT BRACKET (for Lower Side)

Hide 17403 34.INSTALL FRONT NO. 3 EXHAUST PIPE SUB-ASSEMBLY

Hide 37100 35.INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for AWD)

Hide 33820B 36.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.

Install a new clip to the No. 1 transmission control cable bracket.


b.
C102659C02
2.229,1.135 2.76,1.135 true 2.198,0.938 0.438,1.635 0.438,1.635 1.063,0.99 true 2.125,0.625 0.75,0.177 0.75,0.177 1.198,0.635 true 0.563,0.063 0.844,0.313 0.281,0.25 10 false *a 0.271,1.625 0.583,1.885 0.313,0.26 10 false *b 2.771,1.052 3.031,1.313 0.26,0.26 10 false *c
*a Claw (A)
*b Claw (B)
*c Transmission Control Cable Assembly


Install the transmission control cable assembly to the No. 1 transmission control cable bracket.

NOTICE:
·

Make sure that the claws (A) on the clip are securely fit into the No. 1 transmission control cable bracket holes.

·

Make sure that the transmission control cable assembly is securely installed inside of the claws (B) of the clip.




c.

Install the transmission control cable assembly to the transmission control shaft lever with the nut.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)

NOTICE:

Before connecting the transmission control cable assembly, check that the park/neutral position switch assembly and the shift lever are in neutral.



Hide 82121 37.CONNECT ENGINE WIRE

a.

Engage the 2 wire harness clamps.


b.
A315946

Push down the lock lever to connect the ECM connector.

NOTICE:
·

When connecting the ECM connector, make sure that dirt, water or other foreign matter do not contact the connecting part of the ECM connector.

·

Be sure to securely connect the ECM connectors.




c.

Connect the engine wire to the engine room relay block assembly.


d.

Connect the 4 connectors and install the engine wire to the engine room relay block assembly with the nut.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


e.

Connect the 3 wire clamps.


f.

Install the 2 earth wires with the 2 bolts.

Torque:
8.4 N*m (86 kgf*cm, 6 ft.*lbf)


g.

Install the No. 1 relay block cover to the engine room relay block assembly.


Hide 28100 38.INSTALL STARTER ASSEMBLY

Hide 32941 39.CONNECT NO. 1 INLET OIL COOLER HOSE

a.

Connect the No. 1 inlet oil cooler hose and slide the clip to secure it.


Hide 32942 40.CONNECT NO. 1 OUTLET OIL COOLER HOSE

a.

Connect the No. 1 outlet oil cooler hose and slide the clip to secure it.


Hide 23901 41.CONNECT FUEL TUBE SUB-ASSEMBLY

a.

Push the fuel tube connector onto the fuel main tube until the fuel tube connector makes a "click" sound.

NOTICE:
·

Check that there is no damage or foreign matter on the fuel tube connector.

·

After connecting, check that the fuel tube connector and the fuel main tube are securely connected by pulling on them.




b.

Install the No. 1 fuel pipe clamp.


Hide 87246 42.CONNECT OUTLET HEATER WATER HOSE

a.

Connect the outlet heater water hose to the water outlet and slide the clip to secure it.


Hide 87245 43.CONNECT INLET HEATER WATER HOSE

a.

Connect the inlet heater water hose to the water inlet and slide the clip to secure it.


Hide 16572D 44.CONNECT NO. 2 RADIATOR HOSE

a.

Connect the No. 2 radiator hose to the water inlet and slide the clip to secure it.


Hide 16571C 45.CONNECT NO. 1 RADIATOR HOSE

a.

Connect the No. 1 radiator hose to the radiator pipe clamp.


b.

Connect the No. 1 radiator hose to the water outlet and slide the clip to secure it.


Hide 44773F 46.CONNECT UNION TO CHECK VALVE HOSE

a.

Connect the union to check valve hose to the intake air surge tank and slide the clip to secure it.


Hide 23826 47.CONNECT NO. 1 FUEL VAPOR FEED HOSE

a.

Connect the No. 1 fuel vapor feed hose to the No. 1 vacuum switching valve and slide the clip to secure it.


Hide 12363A 48.INSTALL ENGINE MOVING CONTROL ROD

HINT:

Perform this procedure only when replacement of the engine moving control rod or No. 3 engine mounting stay RH is necessary.


a.
A315766C01
0.677,0.833 1.292,1.219 false 2.563,0.635 2.563,1.021 false 2.125,1.354 2.125,1.74 false 2.51,1.073 2.823,1.229 0.313,0.156 10 false *1 0.51,0.74 0.823,0.896 0.313,0.156 10 false *2 2.073,1.781 2.385,1.938 0.313,0.156 10 false *3 0.948,1.25 1.104,1.448 0.156,0.198 10 false A
*1 Engine Moving Control Rod
*2 No. 3 Engine Mounting Stay RH
*3 Engine Moving Control Rod Bracket


Temporarily install the No. 3 engine mounting stay RH and engine moving control rod to the engine moving control rod bracket with the 2 bolts.


b.

Tighten the bolt (A).

Torque:
78 N*m (795 kgf*cm, 58 ft.*lbf)


Hide 12313 49.INSTALL ENGINE MOVING CONTROL ROD BRACKET

a.
A315765N01
1.042,0.01 1.198,0.208 0.156,0.198 10 true A 1.74,0.448 1.896,0.646 0.156,0.198 10 true C 2.208,1.5 2.365,1.698 0.156,0.198 10 true D 2.208,1.76 2.365,1.958 0.156,0.198 10 true B 0.885,1.063 1.042,1.26 0.156,0.198 10 true E

When replacing the engine moving control rod or No. 3 engine mounting stay RH.

i.

Install the engine moving control rod bracket with engine moving control rod with the 4 bolts.

Torque:
38 N*m (387 kgf*cm, 28 ft.*lbf)

NOTICE:

Temporarily tighten the bolt (A) and (B), and then fully tighten the 4 bolts in the order of (C), (D), (A) and (B).



ii.

Tighten the bolt (E).

Torque:
52 N*m (530 kgf*cm, 38 ft.*lbf)



b.
A315764N01
1.021,0.01 1.177,0.208 0.156,0.198 10 true A 1.76,0.438 1.917,0.635 0.156,0.198 10 true C 2.198,1.5 2.354,1.698 0.156,0.198 10 true D 2.198,1.771 2.354,1.969 0.156,0.198 10 true B

When not replacing the engine moving control rod or No. 3 engine mounting stay RH.

i.

Install the engine moving control rod bracket with engine moving control rod with the 4 bolts.

Torque:
38 N*m (387 kgf*cm, 28 ft.*lbf)

NOTICE:

Temporarily tighten the bolt (A) and (B), and then fully tighten the 4 bolts in the order of (C), (D), (A) and (B).




Hide 12327A 50.INSTALL NO. 2 ENGINE MOUNTING STAY RH

a.

Install the No. 2 engine mounting stay RH with the bolt.

Torque:
38 N*m (387 kgf*cm, 28 ft.*lbf)


b.

Tighten the 2 nuts.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)


Hide 47233 51.INSTALL RESERVOIR BRACKET (for LHD)

Hide 47220D 52.INSTALL BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY (for LHD)

Hide 47233 53.INSTALL RESERVOIR BRACKET (for RHD)

Hide 47220D 54.INSTALL BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY (for RHD)

Hide 28800 55.INSTALL BATTERY

a.

Install the battery and battery tray.


b.

Install the battery clamp and battery clamp bolt with the bolt and nut.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


c.

Connect the cable to the positive (+) battery terminal.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)


Hide 17701 56.INSTALL AIR CLEANER CASE SUB-ASSEMBLY

a.

Install the air cleaner case sub-assembly with the 2 bolts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 17801 57.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

a.

Install the air cleaner filter element sub-assembly to the air cleaner case sub-assembly.


Hide 17705 58.INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE

Hide 17750A 59.INSTALL INLET AIR CLEANER ASSEMBLY

a.

Install the inlet air cleaner assembly with the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


b.

Connect the 2 vacuum hose clamps to the inlet air cleaner assembly.


Hide 60.INSPECT VACUUM HOSES

a.

Visually check the vacuum hoses.

A315905


Hide 61.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

a.

Connect the cable to the negative (-) battery terminal.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



Hide 62.INSTALL FRONT WHEELS

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)

Hide 67.ADD TRANSFER OIL (for AWD)

Hide 68.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT

Hide 72.INSPECT ENGINE COOLANT LEVEL IN RESERVOIR TANK

Hide 75.INSPECT FOR OIL LEAK

Hide 76.INSPECT FOR EXHAUST GAS LEAK

Hide 85.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

Hide 11209 86.INSTALL V-BANK COVER SUB-ASSEMBLY

a.

Engage the 3 retainers to install the V-bank cover sub-assembly.


Hide 53295E 87.INSTALL COOL AIR INTAKE DUCT SEAL

Hide 53298E 88.INSTALL RADIATOR SIDE SEAL RH

Hide 53299D 89.INSTALL RADIATOR SIDE DEFLECTOR SEAL LH

Hide 55701J 90.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)

Hide 55701J 91.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)

Hide 92.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 53737B 93.INSTALL FRONT FENDER APRON SEAL LH

a.

Install the front fender apron seal LH with the 2 bolts and clip.


Hide 53736 94.INSTALL FRONT FENDER APRON SEAL RH

a.

Install the front fender apron seal RH with the 2 bolts and clip.


Hide 53876A 95.INSTALL FRONT FENDER LINER LH

a.

Install the front fender liner LH with the 3 screws and 3 clips.


Hide 53875A 96.INSTALL FRONT FENDER LINER RH

a.

Install the front fender liner RH with the 3 screws and 3 clips.


Hide 51442 98.INSTALL NO. 2 ENGINE UNDER COVER

a.

Install the No. 2 engine under cover with the 2 bolts, 2 screws and clip.


Hide 51441 99.INSTALL NO. 1 ENGINE UNDER COVER

a.

Install the No. 1 engine under cover with the 8 bolts, 6 screws and 3 clips.