Home › Drivetrain › U660F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE FLUID › 2013.12–2016.11
RM3160E _52 Drivetrain _019726 U660F AUTOMATIC TRANSMISSION / TRANSAXLE _0107334 AUTOMATIC TRANSAXLE FLUID A

U660F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE FLUID  REPLACEMENT  


PROCEDURE

Hide 1.REPLACE AUTOMATIC TRANSAXLE FLUID

a.

Lift the vehicle. [*1]

NOTICE:

Set the vehicle on a lift so that the vehicle is kept level when it is lifted up (make sure that the tilt angle from the front to rear of the vehicle is within +/- 1°).



b.

Remove the No. 1 engine under cover.

Click hereEngine / Hybrid System>2GR-FE ENGINE MECHANICAL>ENGINE ASSEMBLY>REMOVAL


c.

Separate the front fender liner LH.

Click hereEngine / Hybrid System>2GR-FE ENGINE MECHANICAL>ENGINE ASSEMBLY>REMOVAL


d.

e.
C201682

Remove the refill plug and gasket from the automatic transaxle assembly. [*2]


f.
C239660

Using a 6 mm hexagon socket wrench, remove the overflow plug and gasket from the automatic transaxle oil pan sub-assembly. [*3]


g.
C201684C18
1.208,2.677 0.833,2.677 false 0.604,3.927 0.417,3.927 0.417,3.927 0.708,3.125 false 1.208,3.219 0.833,3.219 false 1.219,2.594 1.375,2.76 0.156,0.167 10 false *1 1.219,3.135 1.385,3.302 0.167,0.167 10 false *a 0.656,3.844 0.833,4.031 0.177,0.188 10 false *b
*1 No. 1 Transmission Oil Filler Tube
*a Hexagon Socket Wrench
*b Overflow Plug Hole


Using a 6 mm hexagon socket wrench, remove the No. 1 transmission oil filler tube from the automatic transaxle oil pan sub-assembly and drain the automatic transaxle fluid. [*4]


h.
C239510

Measure the amount of fluid that you drained. [*5]

HINT:

Add the same amount of fluid in step [*8].



i.

Using a 6 mm hexagon socket wrench, install the No. 1 transmission oil filler tube to the automatic transaxle oil pan sub-assembly. [*6]

Torque:
1.7 N*m (17 kgf*cm, 15 in.*lbf)


j.
C239660

Temporarily install the gasket and overflow plug. [*7]

HINT:

Reuse the old gasket as the overflow plug will be removed again to adjust the fluid level.



k.
C239936

Add fluid to the refill hole using the same amount of fluid drained in step [*5]. [*8]

NOTICE:

Use Toyota Genuine ATF WS.



l.
C201682

Temporarily install the gasket and refill plug to avoid fluid spillage. [*9]

HINT:

Reuse the old gasket as the refill plug will be removed again to adjust the fluid level.



m.

Lower the vehicle. [*10]


n.

Start the engine. [*11]


o.

Slowly move the shift lever from P to D, and then back to P. [*12]


p.

Allow the engine to idle for 30 seconds to warm it up. [*13]


q.

Turn the ignition switch off. [*14]


r.

Repeat steps [*1] to [*14].


s.

Repeat steps [*1] to [*10].


Hide 2.ADJUST FLUID TEMPERATURE (when Using the GTS)

Hide 3.ADJUST FLUID TEMPERATURE (when Not Using the GTS)