Home › Engine / Hybrid System › 2GR-FE ENGINE MECHANICAL › ENGINE ASSEMBLY › 2013.12–2016.11
RM3160E _51 Engine / Hybrid System _019663 2GR-FE ENGINE MECHANICAL _0109582 ENGINE ASSEMBLY A

2GR-FE ENGINE MECHANICAL  ENGINE ASSEMBLY  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

CAUTION:

The engine assembly with transmission is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop.


NOTICE:

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

Hide 3.DISCHARGE FUEL SYSTEM PRESSURE

Hide 4.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 6.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 7.REMOVE FRONT WHEELS

Hide 51441 8.REMOVE NO. 1 ENGINE UNDER COVER

a.

Remove the 8 bolts, 6 screws, 3 clips and No. 1 engine under cover.


Hide 51442 9.REMOVE NO. 2 ENGINE UNDER COVER

a.

Remove the 2 bolts, 2 screws, clip and No. 2 engine under cover.


Hide 58166 10.REMOVE FRONT FLOOR COVER LH

Hide 53876A 11.SEPARATE FRONT FENDER LINER LH

a.

Remove the 3 screws and 3 clips and separate the front fender liner LH.


Hide 53875A 12.SEPARATE FRONT FENDER LINER RH

a.

Remove the 3 screws and 3 clips and separate the front fender liner RH.


Hide 53737B 13.REMOVE FRONT FENDER APRON SEAL LH

a.
A171852

Remove the 2 bolts, clip and front fender apron seal LH.


Hide 53736 14.REMOVE FRONT FENDER APRON SEAL RH

a.
A171853

Remove the 2 bolts, clip and front fender apron seal RH.


Hide 17.DRAIN AUTOMATIC TRANSAXLE FLUID (for 2WD)

Hide 19.DRAIN TRANSFER OIL (for AWD)

Hide 20.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 55701J 21.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)

Hide 55701J 22.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)

Hide 53299D 23.REMOVE RADIATOR SIDE DEFLECTOR SEAL LH

Hide 53298E 24.REMOVE RADIATOR SIDE SEAL RH

Hide 53295E 25.REMOVE COOL AIR INTAKE DUCT SEAL

Hide 11209 26.REMOVE V-BANK COVER SUB-ASSEMBLY

a.
A162365

Hold the rear of the V-bank cover sub-assembly and raise it to disengage the 2 front retainers.


b.

Raise the V-bank cover sub-assembly to disengage the rear retainer to remove the V-bank cover sub-assembly.

NOTICE:

Attempting to disengage both front and rear retainers at the same time may cause the V-bank cover sub-assembly to break.



Hide 17750A 27.REMOVE INLET AIR CLEANER ASSEMBLY

a.
A315760

Remove the 2 bolts and inlet air cleaner assembly.


b.

Separate the air hose from the 2 hose clamps.


Hide 17705 28.REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE

Hide 17801 29.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

a.

Remove the air cleaner filter element sub-assembly from the air cleaner case sub-assembly.


Hide 17701 30.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

a.
A315762

Remove the 2 bolts and air cleaner case sub-assembly.


Hide 28800 31.REMOVE BATTERY

a.
A315761

Disconnect the cable from the positive (+) battery terminal.


b.

Remove the nut and bolt.


c.

Remove the battery clamp, battery clamp bolt, battery and battery tray.


Hide 47220D 32.SEPARATE BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY (for LHD)

a.
C292889C01
0.969,3.948 0.969,3.719 true 0.448,3.938 0.448,3.729 true 0.896,3.979 1.208,4.135 0.313,0.156 10 false *1 0.385,3.969 0.698,4.125 0.313,0.156 10 false *2
*1 Brake Master Cylinder Reservoir Assembly
*2 Reservoir Bracket


Disconnect the reservoir level switch connector and remove the bolt from the brake master cylinder reservoir assembly.


b.

Move the brake master cylinder reservoir assembly as shown in the illustration to disengage the 2 claws, and separate it.


Hide 47233 33.REMOVE RESERVOIR BRACKET (for LHD)

Hide 47220D 34.SEPARATE BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY (for RHD)

a.
C294903C01
0.75,4.094 0.75,3.698 true 0.51,4.094 0.51,3.698 true 0.688,4.094 1,4.25 0.313,0.156 10 false *1 0.448,4.104 0.76,4.26 0.313,0.156 10 false *2
*1 Brake Master Cylinder Reservoir Assembly
*2 Reservoir Bracket


Disconnect the reservoir level switch connector and remove the bolt from the brake master cylinder reservoir assembly.


b.

Move the brake master cylinder reservoir assembly as shown in the illustration to disengage the 2 claws, and separate it.


Hide 47233 35.REMOVE RESERVOIR BRACKET (for RHD)

Hide 12327A 36.REMOVE NO. 2 ENGINE MOUNTING STAY RH

a.
A315763

Remove the bolt, 2 nuts and No. 2 engine mounting stay RH.


Hide 12313 37.REMOVE ENGINE MOVING CONTROL ROD BRACKET

a.
A315764

Remove the 4 bolts and engine moving control rod bracket with engine moving control rod.


Hide 12363A 38.REMOVE ENGINE MOVING CONTROL ROD

HINT:

Perform this procedure only when replacement of the engine moving control rod or No. 3 engine mounting stay RH is necessary.


a.
A315766

Remove the 2 bolts, engine moving control rod and No. 3 engine mounting stay RH from the engine moving control rod bracket.


Hide 23826 39.DISCONNECT NO. 1 FUEL VAPOR FEED HOSE

a.
A171821

Slide the clip and disconnect the No. 1 fuel vapor feed hose from the No. 1 vacuum switching valve.


Hide 44773F 40.DISCONNECT UNION TO CHECK VALVE HOSE

a.
A316003C02
0.094,0.063 0.385,0.333 0.292,0.271 12 false *A 0.135,2.365 0.406,2.604 0.271,0.24 12 false *B
*A for LHD
*B for RHD


Slide the clip and disconnect the union to check valve hose from the intake air surge tank assembly.


Hide 16571C 41.DISCONNECT NO. 1 RADIATOR HOSE

a.
A205873

Slide the clip and disconnect the No. 1 radiator hose from the water outlet.


b.

Separate the No. 1 radiator hose from the radiator pipe clamp.


Hide 16572D 42.DISCONNECT NO. 2 RADIATOR HOSE

a.
A171823

Slide the clip and disconnect the No. 2 radiator hose from the water inlet.


Hide 87245 43.DISCONNECT INLET HEATER WATER HOSE

a.
A205875

Slide the clip and disconnect the inlet heater water hose from the water inlet.


Hide 87246 44.DISCONNECT OUTLET HEATER WATER HOSE

a.
A205876

Slide the clip and disconnect the outlet heater water hose from the water outlet.


Hide 23901 45.DISCONNECT FUEL TUBE SUB-ASSEMBLY

a.
A171827

Remove the No. 1 fuel pipe clamp.


b.
A167796C04
0,0 0,0 false
V100135

Push
V100136

Pull


Disconnect the connector from the fuel main tube by hand. When the connector and the fuel main tube are stuck, push and pull the connector to release it. Pull the connector off of the fuel main tube carefully.

NOTICE:
·

Check for any dirt and foreign matter in the fuel main tube and around the connector. Clean if necessary. Foreign matter may damage the O-rings or cause leaks in the seal between the fuel main tube and connector.

·

Do not use any tools to separate the fuel main tube and connector.

·

Do not forcibly bend or twist the nylon tube.

·

Check for any dirt and foreign matter on the tube seal surface. Clean if necessary.

·

Cover the fuel main tube and connector ends with plastic bags to prevent damage and contamination.

·

If the fuel main tube and connector are stuck together, pinch the fuel main tube between your fingers and turn it carefully to free it. Then disconnect the fuel main tube.




Hide 32942 46.DISCONNECT NO. 1 OUTLET OIL COOLER HOSE

a.
A256231

Slide the clip and disconnect the No. 1 outlet oil cooler hose.


Hide 32941 47.DISCONNECT NO. 1 INLET OIL COOLER HOSE

a.
A256232

Slide the clip and disconnect the No. 1 inlet oil cooler hose.


Hide 28100 48.REMOVE STARTER ASSEMBLY

Hide 82121 49.DISCONNECT ENGINE WIRE

a.
A205864

Remove the No. 1 relay block cover from the engine room relay block assembly.


b.
A320212

Remove the bolt and separate the earth wire.


c.

Remove the nut from the engine room relay block assembly.


d.

Disconnect the 3 wire clamps.


e.
A315806

Disconnect the 4 connectors from the engine room relay block assembly.


f.

Using a screwdriver, disengage the claw and separate the engine wire from the engine room relay block assembly.


g.
A315807

Pull up the lock lever while pushing the lock on the lever to disconnect the ECM connector.

NOTICE:

After disconnecting the ECM connector, make sure that dirt, water or other foreign matter does not contact the connecting part of the ECM connector.



h.

Disengage the 2 wire harness clamps.


Hide 33820B 50.SEPARATE TRANSMISSION CONTROL CABLE ASSEMBLY

a.
C201710

Remove the nut from the transmission control shaft lever.


b.
C296586

Using a screwdriver, disengage the 4 claws, separate the transmission control cable assembly with clip from the No. 1 transmission control cable bracket.


c.

Remove the clip from the transmission control cable assembly.


Hide 37100 51.REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for AWD)

Hide 17403 52.REMOVE FRONT NO. 3 EXHAUST PIPE SUB-ASSEMBLY

Hide 17584B 53.REMOVE NO. 1 EXHAUST PIPE SUPPORT BRACKET (for Lower Side)

Hide 17410 54.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 45220 56.SEPARATE STEERING INTERMEDIATE SHAFT ASSEMBLY (for 2WD)

Hide 45220 57.SEPARATE STEERING INTERMEDIATE SHAFT ASSEMBLY (for AWD)

Hide 88703 58.DISCONNECT DISCHARGE HOSE SUB-ASSEMBLY

Hide 88704 59.DISCONNECT SUCTION HOSE SUB-ASSEMBLY

Hide 17571 60.REMOVE NO. 1 EXHAUST PIPE SUPPORT BRACKET (for Upper Side)

a.
A315767

Remove the 2 bolts and No. 1 exhaust pipe support bracket.


Hide 11361J 61.REMOVE FLYWHEEL HOUSING UNDER COVER

a.
D030471

Remove the 2 bolts and flywheel housing under cover.


Hide 32101A 62.REMOVE DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT (for 2WD)

Hide 32101A 63.REMOVE DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT (for AWD)

Hide 64.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

a.
A315768

Set an engine lifter.

NOTICE:
·

Using height adjustment attachments and plate lift attachments, place the engine assembly with transaxle horizontally.

·

Securely support the engine assembly to prevent it from turning upside down until it is secured to an engine stand.

·

To prevent the oil pan from deforming, do not place any attachments under the oil pan of the engine assembly with transaxle.

·

Do not perform any procedure while the engine assembly with transaxle is suspended because doing so may cause the engine assembly with transaxle to drop, resulting in injury. However, the engine assembly with transaxle needs to be suspended when it is installed to or removed from an engine stand.




b.
A315769C04
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the 6 bolts, 2 nuts and frame side plate RH and frame side plate LH.


c.

Remove the 6 bolts, 2 nuts and front suspension member rear brace RH and front suspension member rear brace LH.


d.

Operate the engine lifter and remove the engine assembly with transaxle from the vehicle.

NOTICE:
·

Make sure that the engine assembly with transaxle is clear of all wiring and hoses.

·

While lowering the engine assembly with transaxle from the vehicle, do not allow it to contact the vehicle.




Hide 65.INSTALL ENGINE HANGERS

a.
A129635C05
1,0.969 1.281,0.969 false 2.792,1.177 2.281,1.177 false 0.073,0.073 0.542,0.375 0.469,0.302 12 false *A 1.688,0.073 2.104,0.385 0.417,0.313 12 false *B 1.323,0.896 1.531,1.083 0.208,0.188 10 true *1 2.115,1.104 2.333,1.302 0.219,0.198 10 true *2 0.313,1.573 0.625,1.729 0.313,0.156 10 false *3 0.865,1.833 1.052,2.01 0.188,0.177 10 true *3 3.146,1.604 3.375,1.781 0.229,0.177 10 false *3 2.604,1.865 2.792,2.042 0.188,0.177 10 true *3
*A for Bank 1
*B for Bank 2
*1 No. 1 Engine Hanger (Part No. 12281-31120)
*2 No. 2 Engine Hanger (Part No. 12282-31100)
*3 Bolt (Part No. 91671-10825) or (Part No. 90119-A0117)


Install the No. 1 engine hanger and No. 2 engine hanger with the 4 bolts as shown in the illustration.

Torque:
33 N*m (337 kgf*cm, 24 ft.*lbf)


b.

Attach the engine sling device and hang the engine assembly with transaxle with the chain block.

NOTICE:
·

Pay attention to the angle of the sling device as the engine assembly or No. 1 engine hanger and No. 2 engine hanger may be damaged or deformed if the angle is incorrect.


·

Do not perform any procedure while the engine assembly with transaxle is suspended because doing so may cause the engine assembly with transaxle to drop, resulting in injury. However, the engine assembly with transaxle needs to be suspended when it is installed to or removed from an engine stand.




Hide 88310 67.REMOVE COMPRESSOR ASSEMBLY WITH PULLEY

Hide 48829A 68.REMOVE FRONT NO. 1 STABILIZER BRACKET LH (for AWD)

Hide 48824A 69.REMOVE FRONT NO. 1 STABILIZER BRACKET RH (for AWD)

HINT:

Perform the same procedure as for the LH side.


Hide 48811 70.REMOVE FRONT STABILIZER BAR (for AWD)

Hide 71.REMOVE STEERING LINK ASSEMBLY (for AWD)

Hide 51100G 72.REMOVE FRONT FRAME ASSEMBLY

a.
A198262

Disconnect the 2 clamps.


b.
A315770

Remove the bolt and disconnect the front engine mounting insulator assembly.


c.
A255443

Remove the nut and disconnect the engine mounting insulator LH.


d.
A255444

Remove the nut and disconnect the engine mounting insulator RH.


e.
A171830

Remove the 2 bolts and disconnect the rear engine mounting insulator assembly.


f.

Remove the front frame assembly.


Hide 12360 73.REMOVE FRONT ENGINE MOUNTING INSULATOR ASSEMBLY

HINT:

Perform this procedure only when replacement of the front engine mounting insulator assembly is necessary.


a.
A315942

Remove the hole plug from the front frame assembly.


b.
A315771

Remove the 3 nuts and front engine mounting insulator assembly.


Hide 12372A 74.REMOVE ENGINE MOUNTING INSULATOR LH

HINT:

Perform this procedure only when replacement of the engine mounting insulator LH is necessary.


a.
A315940

Remove the 2 hole plugs from the front frame assembly.


b.
A255448

Remove the 3 nuts and engine mounting insulator LH.


Hide 12362 75.REMOVE ENGINE MOUNTING INSULATOR RH

HINT:

Perform this procedure only when replacement of the engine mounting insulator RH is necessary.


a.
A315941

Remove the 2 hole plugs from the front frame assembly.


b.
A255449

Remove the 3 nuts and engine mounting insulator RH.


Hide 12380 76.REMOVE REAR ENGINE MOUNTING INSULATOR ASSEMBLY

HINT:

Perform this procedure only when replacement of the rear engine mounting insulator assembly is necessary.


a.
A171843

Remove the 2 hole plugs from the front frame assembly.


b.
A171844

Remove the 2 nuts and rear engine mounting insulator assembly.


Hide 82121 78.REMOVE ENGINE WIRE

a.

Remove the engine wire from the engine assembly with transaxle.


Hide 36118A 81.REMOVE TRANSFER STIFFENER PLATE RH (for AWD)

Hide 30500 82.REMOVE AUTOMATIC TRANSAXLE ASSEMBLY (for 2WD)

Hide 30500 83.REMOVE AUTOMATIC TRANSAXLE ASSEMBLY (for AWD)

Hide 32101 84.REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

Hide 85.INSTALL ENGINE TO ENGINE STAND

a.

Install the engine assembly to an engine stand.

NOTICE:
·

Pay attention to the angle of the sling device as the engine assembly or No. 1 engine hanger and No. 2 engine hanger may be damaged or deformed if the angle is incorrect.

·

Servicing an engine assembly while it is hanging is dangerous. This can be done only when installing/removing the engine assembly to/from an engine stand.




Hide 86.REMOVE ENGINE HANGERS

a.

Remove the 4 bolts, No. 1 engine hanger and No. 2 engine hanger.