Home › Drivetrain › U760E AUTOMATIC TRANSMISSION / TRANSAXLE › DIFFERENTIAL CASE › 2013.12–2014.08
RM3160E _52 Drivetrain _019727 U760E AUTOMATIC TRANSMISSION / TRANSAXLE _0107365 DIFFERENTIAL CASE A

U760E AUTOMATIC TRANSMISSION / TRANSAXLE  DIFFERENTIAL CASE  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL DIFFERENTIAL SIDE GEAR

a.
C301122C01
1.198,0.333 1.021,0.125 1.021,0.125 0.927,0.125 false 0.458,1.521 0.729,1.521 false 0.885,1.323 0.708,1.115 0.708,1.115 0.615,1.115 false 1.438,1.938 1.708,1.938 false 1.438,1.646 1.708,1.646 false 1.76,0.24 1.646,0.24 1.646,0.24 1.385,0.708 false 2,0.563 1.885,0.563 1.885,0.563 1.771,0.792 false 1.885,1.281 1.771,1.281 1.771,1.281 1.635,1.052 false 0.448,1.031 0.865,1.271 0.417,0.24 10 false *1 0.281,1.427 0.635,1.688 0.354,0.26 10 false *2 0.74,0.042 1.135,0.271 0.396,0.229 10 false *4 1.74,1.833 2.135,2.063 0.396,0.229 10 false *4 1.75,1.563 2.104,1.792 0.354,0.229 10 false *3 1.813,0.156 2.167,0.385 0.354,0.229 10 false *3 2.052,0.479 2.406,0.74 0.354,0.26 10 false *2 1.938,1.188 2.354,1.427 0.417,0.24 10 false *1
*1 Front Differential Pinion
*2 Front Differential Pinion Thrust Washer
*3 Differential Side Gear
*4 Front No. 1 Differential Side Gear Thrust Washer


Coat the 2 differential side gears, 2 front No. 1 differential side gear thrust washers, 2 front differential pinions and 2 front differential pinion thrust washers with ATF and install them to the differential case.


Hide 41342F 2.INSTALL FRONT NO. 1 DIFFERENTIAL PINION SHAFT

a.
C138706

Coat the front No. 1 differential pinion shaft with ATF, and install it to the differential case.


Hide 3.INSPECT DIFFERENTIAL SIDE GEAR BACKLASH

Hide 41342A 4.INSTALL FRONT DIFFERENTIAL PINION SHAFT STRAIGHT PIN

a.
C138707

Using a 3 mm pin punch and a hammer, install the front differential pinion shaft straight pin to the differential case.

NOTICE:

Align the holes, and install the front differential pinion shaft straight pin.



b.
C138711

Using a chisel and a hammer, stake the differential case.

NOTICE:

Stake the differential case after adjusting the backlash.



Hide 41311F 5.INSTALL FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING

a.
C201521N07
1.74,0.677 2.396,0.625 2.396,0.625 1.865,0.969 false 1.854,0.802 2.375,0.635 false 2.479,0.521 2.938,0.719 0.458,0.198 10 false SST

Using SST and a press, install a new front differential case rear tapered roller bearing to the differential case.

SST
09710-30012  (09710-04081)
09950-60010  (09951-00480)
09950-70010  (09951-07100)

NOTICE:
·

Do not damage the front differential case rear tapered roller bearing cage when installing the front differential case rear tapered roller bearing.

·

Ensure that there is no clearance between the front differential case rear tapered roller bearing and differential case.




b.
C196828N03
0.885,1.125 0.573,1.396 0.573,1.396 0.74,1.396 false 2.635,1.104 2.563,0.802 2.563,0.802 2.667,0.802 false 0.219,1.323 0.531,1.479 0.313,0.156 10 true SST 2.24,0.719 2.552,0.875 0.313,0.156 10 false SST

Using SST and a hammer, install a new front differential case rear tapered roller bearing outer race to the transaxle case sub-assembly.

SST
09950-60020  (09951-00810)
09950-70010  (09951-07150)

NOTICE:

Ensure that there is no clearance between the front differential case rear tapered roller bearing outer race and transaxle case sub-assembly.



Hide 41311E 6.INSTALL FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING

a.
C297473N01
0.833,0.823 0.406,0.458 0.406,0.458 0.927,0.51 false 0.427,0.469 0.865,0.698 false 2.365,0.604 2.292,0.281 2.292,0.281 2.552,0.323 false 2.302,0.292 2.479,0.51 false 0.104,0.375 0.563,0.573 0.458,0.198 10 false SST 1.99,0.198 2.448,0.396 0.458,0.198 10 false SST

Using SST and a press, install a new front differential case front tapered roller bearing to the differential case.

SST
09523-36010  
09950-60010  (09951-00540)
09950-70010  (09951-07100)

NOTICE:
·

Do not damage the front differential case front tapered roller bearing cage when installing the front differential case front tapered roller bearing.

·

Ensure that there is no clearance between the front differential case front tapered roller bearing and differential case.




b.

Install the shim to the transaxle housing.


c.
C196830N03
0.938,1.24 0.625,1.594 0.625,1.594 0.896,1.531 false 2.604,0.698 2.5,0.698 2.5,0.698 2.552,1.073 false 0.281,1.542 0.594,1.708 0.313,0.167 10 false SST 2.188,0.635 2.49,0.802 0.302,0.167 10 false SST

Using SST and a hammer, install a new front differential case front tapered roller bearing outer race to the transaxle housing.

SST
09950-60020  (09951-00790)
09950-70010  (09951-07150)

NOTICE:

Ensure that there is no clearance between the front differential case front tapered roller bearing outer race, shim and transaxle housing.



Hide 7.ADJUST DIFFERENTIAL SIDE BEARING PRELOAD

a.

Remove any remaining seal packing from the contact surfaces of the transaxle housing and transaxle case sub-assembly.


b.
C205239

Install the differential case to the transaxle case sub-assembly.


c.
C136447N05
1.51,1.615 2.49,1.958 2.49,1.958 2.208,1.646 false 1.906,1.646 2.49,1.958 false 2.573,0.938 3.052,1.104 3.052,1.104 2.49,1.417 false 3.063,1.104 2.604,1.146 false 2,0.615 2.896,0.188 2.896,0.188 2.271,0.76 false 1.781,0.531 2.875,0.198 false 1.344,0.469 0.552,0.271 0.552,0.271 0.875,0.74 false 1.156,0.531 0.552,0.271 0.552,0.271 1.021,0.635 false 0.594,1.021 0.229,1.354 0.229,1.354 0.677,1.604 false 0.573,1.396 0.229,1.354 0.229,1.354 0.542,1.198 false 0.875,1.76 1.188,1.979 1.188,1.979 1.313,1.729 false 1.188,1.969 1.115,1.802 false 2.917,0.094 3.052,0.25 0.135,0.156 10 false A 2.5,1.865 2.635,2.021 0.135,0.156 10 false B 0.385,0.156 0.521,0.313 0.135,0.156 10 false A 3.083,1.031 3.219,1.188 0.135,0.156 10 false A 1.177,1.99 1.313,2.146 0.135,0.156 10 false A 0.083,1.271 0.219,1.427 0.135,0.156 10 false A

Install the transaxle housing to the transaxle case sub-assembly with the 20 bolts.

Torque:
Bolt (A) : 30.6 N*m (312 kgf*cm, 23 ft.*lbf)
Bolt (B) : 22.7 N*m (231 kgf*cm, 17 ft.*lbf)


d.
C138262N16
0.841,4.027 1.205,4.212 0.364,0.184 10 SST 1.079,3.308 0.973,4.027 false

Using SST, turn the differential case right and left 2 or 3 times to settle the bearings.

SST
09564-33010  


e.

Using SST and a torque wrench, measure the turning torque of the counter driven gear while rotating SST at 10 rpm.

SST
09564-33010  

Turning Torque:

1.5 to 1.7 N*m (16 to 17 kgf*cm, 14 to 15 in.*lbf)


If the turning torque is not within the specified range, refer to the table below to select a shim so that the turning torque is within the specified range.

Shim Thickness: mm (in.)
Thickness Thickness Thickness Thickness
2.000 (0.0787) 2.225 (0.0876) 2.450 (0.0965) 2.675 (0.105)
2.025 (0.0797) 2.250 (0.0886) 2.475 (0.0974) 2.700 (0.106)
2.050 (0.0807) 2.275 (0.0896) 2.500 (0.0984) 2.725 (0.107)
2.075 (0.0817) 2.300 (0.0906) 2.525 (0.0994) 2.750 (0.108)
2.100 (0.0827) 2.325 (0.0915) 2.550 (0.100) 2.775 (0.109)
2.125 (0.0837) 2.350 (0.0925) 2.575 (0.101) 2.800 (0.110)
2.150 (0.0846) 2.375 (0.0935) 2.600 (0.102) 2.825 (0.111)
2.175 (0.0856) 2.400 (0.0945) 2.625 (0.103) 2.850 (0.112)
2.200 (0.0866) 2.425 (0.0955) 2.650 (0.104) 2.875 (0.113)


f.
C287968

Remove the 20 bolts and transaxle housing from the transaxle case sub-assembly.


g.
C205239

Remove the differential case from the transaxle case sub-assembly.


Hide 41221 8.INSTALL FRONT DIFFERENTIAL RING GEAR

a.
D025215

Using ATF and a heater, heat the front differential ring gear to 90 to 110°C (194 to 230°F).

NOTICE:

Do not heat the front differential ring gear to more than 110°C (230°F).



b.

Clean the contact surface of the differential case.


c.
C138531C10
1.25,1.427 0.938,0.76 0.938,0.76 1.188,1.5 false 0.833,0.563 1.188,0.771 0.354,0.208 10 false *a
*a Matchmark


Align the matchmarks, and install the front differential ring gear to the differential case quickly.

NOTICE:

Do not install the bolts while the front differential ring gear is hot.



d.
C138532

Install and tighten the 12 bolts.

Torque:
120 N*m (1224 kgf*cm, 89 ft.*lbf)

NOTICE:
·

Tighten the bolts after the front differential ring gear has cooled down sufficiently.

·

Tighten the bolts evenly in a diagonal pattern using several steps.




Hide 43410M 9.INSTALL FRONT DRIVE SHAFT OIL SEAL RH

a.

Coat the lip of a new front drive shaft oil seal RH with MP grease.


b.
C196831N02
1.427,1.313 0.635,2.333 0.635,2.333 1.375,1.542 false 2.156,1.865 2.615,1.865 2.615,1.865 2.542,2.083 false 0.271,2.281 0.583,2.448 0.313,0.167 10 true SST 2.698,1.802 3.167,2.063 0.469,0.26 10 false SST

Using SST and a hammer, install the front drive shaft oil seal RH to the transaxle case sub-assembly.

SST
09316-10010  
09950-70010  (09951-07100)

Standard Depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:

Check that the front drive shaft oil seal RH is installed in the correct direction.



Hide 43420H 10.INSTALL FRONT DRIVE SHAFT OIL SEAL LH

a.
C301313N01
0.542,0.302 0.688,0.302 0.688,0.302 0.969,0.802 true 2.052,1.927 2.427,1.927 false 0.229,0.219 0.667,0.448 0.438,0.229 10 false SST 1.74,1.854 2.177,2.083 0.438,0.229 10 false SST

Coat the lip of a new front drive shaft oil seal LH with MP grease.


b.

Using SST and a hammer, install the front drive shaft oil seal LH to the transaxle housing.

SST
09308-14010  

Standard Depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:

Check that the front drive shaft oil seal LH is installed in the correct direction.