Inspect the fuses for circuits related to this system before performing the following inspection procedure.
The steering wheel heater unit is built into the steering wheel assembly which cannot be disassembled. Therefore, when the steering wheel heater unit has a malfunction, replace the steering wheel assembly.
| *a | Front view of wire harness connector
(to Steering Wheel Heater Control Assembly) |
Disconnect the B steering wheel heater control assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-1 (TH1) - B-2 (TH2) | 10 to 30°C (50 to 86°F) | 8.132 to 18.43 kΩ |
| B-4 (SH1) - B-3 (SH2) | 20°C (68°F) | 1.89 to 2.25 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the connectors and cables of the spiral cable sub-assembly.
There are no defects such as scratches, cracks, dents or damage on the connectors or cables.
Disconnect the F62 and z7 spiral cable sub-assembly connectors.
Measure the resistance according to the value(s) in the table below.
| *a | Component without harness connected (Spiral Cable Sub-assembly) | - | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z7-1 (BTM) - F62-1 (BTM) | Always | 3 Ω or less |
| z7-2 (ETM) - F62-3 (ETM) | Always | 3 Ω or less |
| z7-3 (EHT) - F62-2 (EHT) | Always | Below 0.1 Ω |
| z7-4 (BHT) - F62-4 (BHT) | Always | Below 0.1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected (Steering Heater Switch) |
Disconnect the F45 steering heater switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F45-3 (IG) - F45-6 (IN) | Steering heater switch is pushed | Below 1 Ω |
| F45-3 (IG) - F45-6 (IN) | Steering heater switch is not pushed | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | IG1 NO. 4 Relay (Steering Heater Relay) |
Remove the IG1 No. 4 relay (steering heater relay) from the No. 2 engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 - 5 | Voltage is not applied between terminals 1 and 2 | 10 kΩ or higher |
| 3 - 5 | Voltage is applied between terminals 1 and 2 | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F45 steering heater switch connector.
Disconnect the F62 spiral cable sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F45-7 (+) - F62-1 (BTM) | Always | Below 1 Ω |
| F45-6 (IN) - F62-3 (ETM) | Always | Below 1 Ω |
| F45-7 (+) or F62-1 (BTM) - Body ground | Always | 10 kΩ or higher |
| F45-6 (IN) or F62-3 (ETM) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the IG1 No. 4 relay (steering heater relay) from the No. 2 engine room relay block.
Disconnect the F62 spiral cable sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 - F62-4 (BHT) | Always | Below 1 Ω |
| 3 or F62-4 (BHT) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F45 steering heater switch connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F45-3 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the IG1 No. 4 relay (steering heater relay) from the No. 2 engine room relay block.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 5 - Body ground | Always | 11 to 14 V |
| 1 - Body ground | Ignition switch ON | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F62 spiral cable sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F62-2 (EHT) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG